PORTABLE WLAN SERVER ROUTER 3,5G PRO User Manual 1 Version 1.
Table of Content FCC CAUTION ...................................................................................................................................... 9 SAFE SEATING GESTURES .............................................................................................................. 10 CE STATEMENT OF CONFORMITY .................................................................................................. 10 CHAPTER 1 INTRODUCTION ..........................................................
.2.8 Firewall Setup ........................................................................................................... 38 3.2.9 QoS Configuration Setup ........................................................................................ 39 3.2.10 FTP Server Setup ..................................................................................................... 40 3.2.11 Printer Server Setup ..............................................................................................
3.6 SYSTEM MANAGEMENT ......................................................................................................... 88 3.6.1 Reboot ....................................................................................................................... 88 3.6.2 Change Password .................................................................................................... 88 3.6.3 Firmware Upgrade..........................................................................................
4.3.1 LAN ...........................................................................................................................117 4.3.2 Wireless ...................................................................................................................119 4.4 SERVER .............................................................................................................................. 123 4.4.1 Samba Server .........................................................................
4.9 SITE M AP ........................................................................................................................... 158 CHAPTER 5 CLIENT MODE ............................................................................................................. 159 5.1 ADMINISTRATOR QUICK SETUP ............................................................................................ 159 5.2 QUICK SETUP ......................................................................................
5.5.4 Profile Save ............................................................................................................. 191 5.5.5 Remote Management ............................................................................................. 192 5.5.6 Time ......................................................................................................................... 193 5.5.7 UPnP Setting ..............................................................................................
.3 USB DEVICES .................................................................................................................... 226 8.4 OPERATING SYSTEMS ......................................................................................................... 227 8.5 BROWSERS ........................................................................................................................ 227 8.6 EASY SETUP ...................................................................................
FCC Caution The device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. 2. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Safe Seating Gestures You should follow the manufacturer’s instructions for adjusting the backrest to fit your body properly. An adjustable chair that provides firm, comfortable support is best. Adjust the height of the chair so your thighs are horizontal and your feet flat on the floor. The back of the chair should support your lower back (lumbar region).
Chapter 1 Introduction 1.1 Overview MT4205 might be small in size, but is huge in functionality, supporting multiple operation modes, including Access Point (AP) mode, Router mode, and Wireless Client mode. You can switch among these modes easily by using MT4205's 3-way configuration switch. In addition to, there are 2 USB ports available for connecting any devices which allow LAN users to utilize shared printer and samba server.
1.2 Features MT4205’s main functions, including Wireless Access, Printer Server, Webcam Monitor, Samba Server, FTP Server and IP Sharing etc. are shown as below. These features and their applying instructions specified in User Manual will not only fulfill your requirements, but also ease your inconvenience from the job. Easy Setup Proprietary utility is designed to let users, even the beginners, complete their server setups easily and access Internet without any difficulty.
1.3 Specifications Components Interface Function Application Management CPU Star 9105gu Flash ROM 8Mbyte (NAND Gate) DRAM 32MByte WAN Port 1 x 10/100 Mbps RJ45, with auto MDI/MDIX LAN Port 1 x 10/100 Mbps RJ45, with auto MDI/MDIX USB2.0 Port 2 x Standard _A type—USB 2.0 for 3.5G USB Dongle, USB Webcam, USB printer, USB Flash/HDD Wireless Ralink 2561 Mini_PCI Slide Switch Router / AP / Client mode exchange function.
1.3.1 Six Views of Product Appearance 14 Version 1.
1.4 System Requirements To begin with MT4205, you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles on your system. XDSL/Cable Modem and broadband Internet Account. One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card. TCP/IP and at least one web browser software installed (E.g.: Internet Explorer 5.0, Netscape Navigator 7.x, Apple Safari 2.03 or higher version). At lease one 802.
【Step 2】 Click on Properties 【Step 3】 Double click on Internet Protocol (TCP/IP). 16 Version 1.
【Step 4-1】 For getting IP automatically if you are one of the users under MT4205, please skip Use the following IP address and then select Obtain an IP address automatically and Obtain DNS server address automatically and then click on OK button. 【Step 4-2】 For getting IP manually in order to specify a Virtual Server, such as Print Server, FTP Server and so on, please skip Obtain an IP address automatically and then select Use the following IP address.
1.5.1 Network Testing There are two ways to test your Network whether it can work on Internet or not. They are ―Testing with Internet Browser‖ and ―Testing with Dos‖. 1.5.1.1 Testing with Internet Browser Open an Internet Browser, such as Internet Explore or Netscape. Input a valid web address you like, for example, http://www.yahoo.com in the web address blank and then press enter. If the website appears, that means your Internet is working under normal situation. 1.5.1.
【Step 1】 Go to start > Run. 【Step 2】 Input cmd in the blank, and then click OK button. The Command Prompt window appears. 【Step 3】 Input ipconfig in the flashing area then press enter. You will get an IP Address 192.168.1.100, for example, and Default Gateway as 192.168.1.1. 【Step 4】 Ping a legal WAN Address such as 192.168.1.1. If Internet works, it will show Reply from 192.168.1.1: bytes = 32 time = 3ms TTL =64, for example. 19 Version 1.
If it can’t work, it will show Request timed out. 20 Version 1.
Chapter 2 Hardware Installation 2.1 Diagram of Connecting Hardware to MT4205 MT4205 is a portable and convenient wireless solution for the traveling businessmen delivering 802.11g wireless connectivity with a maximum wireless signal rate of up to 54Mbps. Use it in conference rooms, hotel rooms, or even at hotspots. The Wireless Pocket Router/AP might be small in size, but is huge in functionality, supporting multiple operation modes, including Access Point (AP) mode, Router mode, and Wireless Client mode.
2.1.2 AP Mode Hardware Connection and Application Under AP Mode, it supports 2 LAN ports as Bridge, and user can connect to MT4205 via LAN port or Wireless (WDS). The administrator can set up quickly, including LAN Setup, Wireless Setup, Time Server Setup, Password Setup, USB Disk Management Setup, User Account Management Setup, FTP Server Setup, Web Camera Setup, Printer Server Setup and Samba Setup. 2.1.
Chapter 3 Router Mode 3.1 Administrator Quick Setup Instruction Make sure to switch the mode into Router Mode, then open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://192.168.1.1 (Default Gateway) into browser’s blank. Notice: If the homepage doesn’t appear, please check if the TCP/IP configuration is obtaining IP address automatically or not. If you don’t know how to do it, please refer to ―1.5 Get your IP Automatically & Manually‖.
User Name and Password The default values for User Name and Password are admin (all in lowercase letters). Click Login to enter. Notice: Only the password can be changed, please read setup ―3.2.5 Password Setup‖ or ―3.6.2 Change Password‖. In order to protect your own settings, it’s strongly recommended to change the password before you finish the Router Basic Setup. 3.2 Quick Setup Typical Configuration Manager Page consists of two separate frames.
The above diagram shows all PCs and devices connected to your MT4205 and their status. Click Quick Setup on the left of the main menu. Then you’ll see the full functionality selection screen appears and detailed settings for each item, including ―Basic‖ and ―Application‖ two parts. Note: The device models named of USB Device, Webcam and Printer will be shown under the picture of each device if the product supports.
Quick Setup Instruction WAN Setup: Setup the connecting type provided by your ISP, 5 modes of WAN connection are supported by MT4205–Static IP, Dynamic IP, PPPoE, PPTP and HSDPA/UMTS. LAN Setup: Setup the IP Address for LAN and Group. If you are using the Router with multiple PCs on your LAN, you must connect the LAN via the Ethernet ports on the built-in Ethernet switch. You should also assign a unique IP address to each device residing on your LAN.
See 3.2.1.1 See 3.2.1.2 See 3.2.1.3 See 3.2.1.4 See 3.2.1.5 Choose your WAN type as the above mentioned, and its associated settings will show up underneath at the same time. 3.2.1.1 WAN Type – Static IP Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter the IP address, IP Netmask and IP gateway as provided. Each entered fields must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x).
Please click on Next button to go on 3.2.2 LAN Setup. 3.2.1.2 WAN Type – Dynamic IP Choose Dynamic IP to obtain IP address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services. If ISP provided you DNS information, please select Specify DNS Server IP; otherwise, select No Default DNS Server. In particular, here provides 3G or 3.5G transmission rate when the device is plugged, either a 3.
IP connection is back during the next detection. Input it if requested by your ISP (Ex: Wireless Mobile Router) MAC address Click on Next button to go on 3.2.2 LAN Setup. 3.2.1.3 WAN Type – PPPoE This option is typically used for DSL services. Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses PPPoE connection. Your ISP will provide you with a username and password. MTU stands for Maximum Transmission Unit.
In particular, here provides 3G or 3.5G transmission rate when the device is plugged, either a 3.5G USB Dongle or Card Bus; just check to apply for the backup. In other words, once Dynamic IP connection is disconnected, the system automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals until none existed. The default interval between the two connection detection is 3 minutes. The interval range is from 1 to 3 minutes. The 3.
This option is typically used for DSL services. Some DSL service providers supply a special DSL modem. This kind of modem only supports the PPTP tunnel to access the Internet, you should create a PPTP tunnel that carries a PPP session and terminates on the DSL model. Once the tunnel has been established, this kind of DSL modem will forward the PPP session to the ISP. As long as the PPP session is connected, all the local users will be able to share this PPP session to access to the Internet.
PPTP Server IP, My WAN IP and My WAN Subnet Mask are all necessary inputs. The fields on the left are required. Please enter the account’s name and password which provided by your ISP, and then click on Next button to go on 3.2.2 LAN Setup. 3.2.1.5 HSDPA/UMTS If you are using HSDPA/UMTS (3.5G connection) as the WAN Type, please check HSDPA/UMTS selection and fill in the required information as follows to directly access Internet via connected 3.5G adapter.
Always: Stay connected all the time. After the Quick Setup is finished, the Internet connection is on automatically. If disconnection is detected, the system will carry on re-connection immediately in order to stay online. Dial on Demand: Connect to the Internet when it is needed. After the Quick Setup is finished, the Internet connection is on automatically. When it is idled for the set-value (0~60 Minutes), the connection will be disconnected automatically.
each device residing on your LAN. The LAN IP address identifies the router as a node on your network; that is, its IP address must be in the same subnet as the PCs on your LAN. The default LAN IP for the Internet Security Router is 192.168.1.1. The setup of pre-assigned Gateway IP Address is suggested for good to use. Requested to be as complied as LAN IP. For Gateway IP Address, the IP address 192.168.1.xxx (xxx can be any number between 1 and 254 that is not used by another device.
Select AP/Bridge or WDS from drop-down list. You can use the default ESSID unless more than one AP/Router is deployed in the same area. And it will show when searching the wireless signal. For selecting configuration utility in AP/Bridge wireless connection, the Channel 6 is the default channel; all devices on the network must be set to the same channel to communication on the network. The default TxPreamble setting is Long (if you use high traffic networks should use the shorter preamble type).
router’s date and time does not affect the date and time on your PCs. Select your time zone from the “Time Zone” drop-down list or you may set the time by manual. Select your time zone from the Time Zone drop-down list, or you may set the time manually; there is no real time clock inside the router, the system date and time are maintained by external network time server. 3.2.5 Password Setup Here suggests changing the password for logging into the configuration manager in terms of security reason.
3.2.6 USB Disk Management Setup Easy to check all the USB storage devices connected to your MT4205, view the entire data folder inside each storage device, and you can manage the disk formatting/partitioning via click on the button of this page. Select the USB Disk and click on OK button for refreshing all disks before you execute disk partition, and the Unplug button will appear. To partition/format the disk, please select the disk and click on Format button.
Input the User’s name and password, and then click on “Add”, and you will see the user information appear on the “User Account List” Set each user’s right and space arrangement, and then click on Add button for saving user’s account. Click on Next button after finished. 3.2.8 Firewall Setup The Firewall rules of MT4205 are an advance feature used to deny or allow traffic from passing through the router. 38 Version 1.
The default setting for Firewall Protection Level security is Low, which attacks Blocking Policy, allow all Inbound and Outbound IP Filter Policy, and allow all router service access policy from WAN. Please change it as your demand, and click on Next button to next step (see also 3.4.2.1 Firewall Configuration). 3.2.9 QoS Configuration Setup QoS management helps to set and evaluate QoS policies and goals.
3.2.10 FTP Server Setup MT4205 can be the FTP Server providing users to transmit files, also for the guest to download the files from assigned website. Moreover, by connecting USB HDD, USB Flash to the router, user can easily set up a FTP Server to share or download files for local or remote users. If the USB device isn’t enabled first, you can’t enable FTP Server. (Not even click on “Enable”) Set the FTP Server and related setting. Disable the function as demand, and click on Next button to continue.
If you plan to use MT4205 as a Web Camera site, connect a supported USB Web Camera to the USB port of MT4205. Check to enable the server and WAN access by demand. Make sure the webcam already connected to 3.5G plus WLAN Mobile Server Router, and then select “Enable” under your demand and situation; moreover, you have to make sure the “image format” which you want to see on the screen. Click on Next button to next step.
To apply your new settings, please click on Finish button to reboot system automatically and go to the product’s diagram homepage. You may connect to Internet via wired or wireless at this moment according to above settings. 3.3 IP Configuration This function allows you to add routing rules into MT4205. It is useful if you connect several computers behind MT4205 to share the same connection to Internet. 3.3.1 WAN Select WAN under the IP Config menu. MT4205 supports four WAN connection types, i.e.
If you applied for a Static IP connection type from ISP, please follow the steps to set up your WAN connection. 1. IP Address Input your IP Address supplied by ISP. If you don’t know, please check with your ISP. 2. Subnet Mask Input Subnet Mask, normally it is 255.255.255.0. 3. ISP Gateway Address Input ISP Gateway Address. If you don’t know, please check with your ISP. 4. HSDPA/UMTS Backup The default interval between the two connection detection is 3 minutes, and the range is from 1 to 3 minutes.
This feature requires user to enter user name, password and SIM PIN etc.; also it is working as mutual backup for other 4 WAN Types. That is, setting up the interval time to auto detect whether the Internet connection is lost or not. If yes, the system immediately switches to 3.5G Internet connection until the original connection is back during the next detection. 6.
1. Host Name The host name is optional; but if your ISP requires you to input a specific host name, please put it in, for example, MT4205 applied from ISP. Generally, Cable Modem will provide the hostname information. 2. MAC Address: Keep, Clone & Input MAC Address Select Keep or Clone MAC Address for copying the MAC address of your Ethernet adapter to the gateway, or input a group of MAC Address. Generally, your ISP will inform you. 3.
working as mutual backup for other 4 WAN Types. That is, setting up the interval time to auto detect whether the Internet connection is lost or not. If yes, the system immediately switches to 3.5G Internet connection until the original connection is back during the next detection. 5. DNS If ISP provides you DNS information, please select Specify DNS Server IP and input the DNS information into the blank; otherwise, select No Default DNS Server. 6. Apply & Cancel Click on Apply button to continue.
1. User Name Input your user name supplied by ISP. If you don’t know, please check with your ISP. 2. Password Input your Password supplied by ISP. 3. MTU MTU stands for Maximum Transmission Unit. For PPPoE connection, you may need to set the MTU setting in order to work correctly with your ISP. 4. Idle Time It is the time of inactivity before disconnecting your PPPoE session.
1. PPTP Select connect to PPTP by Dial On Demand, Always Online or Manual connects. 2. PPTP Account Input the PPTP Account supplied by ISP, MT4205, for example. If you don’t know, please check with your ISP. ※ Notice: Don’t copy the mentioned example as yours. 3. PPTP Password Input the Password supplied by ISP. 4. Retype your Password Retype the password into this blank for confirming. 48 Version 1.
5. PPTP Server IP Input the Server IP supplied by ISP. If you don’t know, please check with your ISP. Input the WAN IP address provided by your ISP. 6. My WAN Subnet Mask Input the WAN Subnet Mask supplied by your ISP. If you don’t know, please check with your ISP. 7. MTU MTU stands for Maximum Transmission Unit. For PPTP connections, you may need to set the MTU setting in order to work correctly with your ISP. 8. Maximum Idle Time It is the time of inactivity before disconnecting your PPTP session.
When 3.5G signal cannot be reached, the system starts to search downward for 3/2.75/2.5G signals until none existed. 1. 3.5G This feature requires user to enter user name, password and SIM PIN etc.; also it is working as mutual backup for other 4 WAN Types. That is, setting up the interval time to auto detect whether the Internet connection is lost or not. If yes, the system immediately switches to 3.5G Internet connection until the original connection is back during the next detection. 2.
Connect to the Internet by setting up each time. After the Setup is finished, user has to go to Network Configuration page to manually set up the connection and disconnection. 5. DNS If ISP provides you DNS information, please select Specify DNS Server IP and input the DNS information into the blank; otherwise, select No Default DNS Server. 6. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clear the settings on this page. 3.3.
8. DNS This field indicates the IP address of DNS to provide to clients that request IP Address from DHCP Server, the default setting is the same with LAN IP address. 9. WINS The Windows Internet Naming Service manages interaction of each PC with the Internet. If you use a WINS server, enter IP Address of server here. 10. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clear the settings on this page.
1. Wireless Select AP/Bridge or WDS to allow or disallow the wireless operation. 2. Wireless Mode This field indicates the 802.11g interface mode. ―802.11G‖ prevents the 802.11b clients from accessing the router. ―802.11B/G‖ allows both 802.11b and 802.11g clients to access the router. ―802.11B‖ will enable the network as an 802.11b wireless network. By default, the mode is ―802.11B/G‖. 3.
5. Channel IEEE 802.11g and 802.11b devices are direct sequence spread spectrum devices that spread a radio signal over a range of frequencies. The range of frequencies used by a direct sequence device is called Channel. The 802.11g and 802.11b specification supports up to 14 overlapping Channels for radio communication. But only 11 Channels are supported in the United States and therefore built-in on MT4205. To minimize interference, configure each of MT4205 to use Non-overlapping channels.
WEP Keys. The ―1280bit‖ method is more secure than the ―64-bit‖. Key Type: For 64bits WEP key, either 5 ASCII characters or 10 hexadecimal digitals leading by 0x can be entered. For 128bits WEP key, either 13 ASCII characters or 26 hexadecimal digits leading by 0x can be entered. Note: 128 bits WEP is most secure, but has more encryption/decryption overhead. Note that all wireless devices must support the same WEP encryption bit size and have the same key.
Radius with 802.x: Check this circle to enable Radius client function. WPA Rekey Timer: Allows for the session keys to be refreshed over time, minimizing the amount of data that is encrypted with the same session key. RADIUS Server IP: The IP address of RADIUS server. RADIUS Server Port: The UDP port number that the RADIUS server is listed. The default value is 1812. Shared Secret: The RADIUS server and client share a secret that is used to authenticate the messages sent between them.
1. Service Provider Choose correct Service Provider from drop-down list, here including dyndns, dhs, ods and tzo embedded in MT4205. 2. Enable / Disable DDNS Select enable to use DDNS function. Each time your IP address to WAN is changed, and the information will be updated to DDNS service provider automatically. 3. Host Name This field represents the host name you register to Dynamic-DNS service and expect to export to the world. 4. User Name User name is used as an identity to login Dynamic-DNS service.
3.4.1 NAT NAT is a method of mapping one or more IP addresses and/or services ports into different specified services, where NAT stands for Network Address Translation. It allows the internal IP addresses of many computers on a Local Area Network (LAN) to be translated to one public address, saving users’ cost. It also plays a security role by obscuring the true IP addresses of important machines from potential hackers on the Internet.
into MT4205. 2. Description: Enter the description of the virtual server, this field allows you to record what this rule is used for. 3. Private IP: Specify the private IP address of the internal host offering the service. 4. Protocol Type: Specify the transport layer protocol (TCP or UDP). 5. Private Port: Specify the private port number of the service offered by the internal host. 6. Public Port: Specify the private IP address of the internal host offering the service. 7.
3.4.2 Firewall The Firewall function helps to protect your local network against attacks from outside. It also provides a way of restricting users on the local network from accessing the Internet. Additionally, it can filter out specific packets to trigger the router to place an outgoing connection. 3.4.2.
1. Firewall Protection Level: Select the level from the drop-down list, including High, Medium and Low. The below screen including SPI service and ICMP setting will change according to your level setup. 2. Enable SPI Service: MT4205 often monitor a wider range of activity, such as patterns of traffic and the type of application sending traffic.
the FTP server machine and an arbitrary port on another system. This connection may be used to bypass access controls that would otherwise apply. IP Unaligned Time-Stamp: Check or un-check this option to enable or disable protection against unaligned IP time stamp attack. Certain operating systems will crash if they receive a frame with the IP timestamp option that isn’t aligned on a 32-bit boundary.
The list shows all the DoS attacks blocking items. 3.4.2.2 IP Filter Use IP Filter to deny LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for the specific IP address. 1. Enable IP Filter: Check enable or disable to apply IP Filter function. 63 Version 1.
2. Enable Log: All packets between WAN and LAN will be logged. 3. Source: To specify the appropriate IP address / mask and enter the source port number. 4. Destination: Allows you to set the destination address / mask to which this rule should apply and enter the source port number. 5. In/Out: Select inbound or outbound ACL (Access Control List) rules, you can control (allow or deny) incoming or external network access to computers on your LAN. 6. Protocol: This option allows you to select protocol type.
1. MAC Filter Action: To deny or allow all MAC filter action. 2. Enable MAC Filter: Check enable or disable to apply MAC Filter function. 3. Enable Log: All packets between WAN and LAN will be logged. 4. Description: Enter the filter description into this blank. 5. MAC Address: Enter the MAC address manually that you want to filter. 6. Time Ranges: Apply MAC filter by setting time ranges. 7.
1. Enable URL Filter: Check enable or disable to apply URL filter function. 2. Enable log: All packets between WAN and LAN will be logged. 3. Description: Enter the filter description into this blank. 4. URL keyword: Enter the URL words into this blank to apply filter blocking, example: ―www.yahoo‖, then it’ll block all the websites from www.yahoo range. 5. Time Ranges: Apply URL filter by setting time ranges. 6.
3.4.3 QoS Quality of Service (QoS) refers to the capability of a network to provide better service to selected network traffic over various technologies, including Frame Relay, Asynchronous Transfer Mode (ATM), Ethernet and 802.1x networks, and IP-routed networks that may use any or all of these underlying technologies.
1. Enable QoS Service: One checkbox appears to activate the QoS control function or not. Click it to force the router to perform QoS control over traffic flows. By default, it’s enabled. 2. Current Upstream Bandwidth: Allows you to set the upper bound of the port forwarding rate. It will be of great value to minimize the impact on other users from one user who would otherwise monopolize the network transmission bandwidth (e.g. playing games or downloading large files). 3.
1. Enable Samba Server Check to Enable/Disable while connecting. 2. Workgroup Name Fill in the name, and the default is Workgroup. 3. Server Name Name your server. 4. Server Description Describe your server by demand, and the default is Wireless Mobile Router. 5. Printer Model Printer model appears when connected. 6. Apply & Cancel Click Apply to save or Cancel to clear settings. 3.5.1.1 How to Access File Sharing Directory Please follow the steps below. 【Step 1】 Go to Start and click My Computer.
【Step 2】 Fill in blank address field with \\192.168.1.1. 【Step 3】 A window pops up asking for user name and password. If log in as an administrator, please enter admin for both fields; otherwise, fill in with personal account and password. Click OK after finished. 【Step 4】 As the window below appears, login user has entered file sharing directory, and the folders underneath are all available for sharing locally. 70 Version 1.
Note: Only 2 icons show up at most. 1. If a USB flash drive/hard disk is connected and enabled, the samba folder shows up. 2. If a USB printer is connected and enabled, the printer icon shows up. 3.5.2 FTP Server By directly connecting USB storage devices to any USB port, FTP server can be created with simple configuration. FTP Server utility allows both local and remote users to upload or download files, pictures or music files from the same storage device in most easy and timely fashion.
While USB storage device is plugged，FTP Server can be checked as enabled. 1. Enable FTP Server: Enabling selection for FTP Server only can be checked when USB storage device is plugged. 2. Enable Anonymous to Login: Allow anonymous to log in after check on enable. 3. Enable FTP Access from WAN: Allow FTP access from WAN side by checking on enable for this item. 4. FTP Server Port: Define the FTP command transfer service port.
3.5.3.1 Web Camera Server Basic Setup 1. Enable Webcam Server: Allow using this function by checking on enable. 2. Access from WAN: Allow webcam can access from WAN side by checking on enable for this item. 3. Image format: The default is 320x240 pixels. 4. Preview: Click on this button, you can preview the image from webcam. 5. Record Setting: Please see the detail advance setting in 3.5.3.2 Web Camera Server Advanced Configuration. 6. Apply & Cancel Click on Apply button to continue.
HDD or remote FTP; if select save to remote FTP, please continue follow-up remote FTP setting. 4. USB HDD Directory: The section provides option of which folder should be used for saving webcam image. 5. Remote FTP URL: Input the FTP URL for saving webcam image. 6. Remote FTP port: Input the FTP port number under URL to save image. 7. Remote FTP user: Enter the user’s name you like and it will be used to save the webcam image into the FTP server. 8.
monitoring or recording of all images into the USB HDD for reviewing. Often marketed as surveillance tools for home or office security; network Webcams are now being employed by early adopters for more personal matters, such as watching kids and monitoring pets. The Webcam can be remotely accessed and controlled via a browser. In addition, record and monitor live actions with USB webcam; then view the image through Internet browsers or WiFi mobile phones. 3.5.3.3.1.
Input the WAN IP Address (as you see on above screen) into browser blanks. You will see the personal account login screen appear, and then input your own user account and password. After logging in as a user, your will see the personal control panel screen as below, please click on My Webcam. There will pop-up screen shows the image from web camera as example below. 3.5.3.3.1.2 Web Camera Monitoring via WiFi Mobile Phone You may view the monitor live action through WiFi mobile phones. 76 Version 1.
Please fill the WAN IP address plus ―/webcam.html‖ (e.g. http://210.64.134.25/webcam.html) into the mobile phone’s browser blank and you will see the webcam user login screen appear as below. After logging in with your own account, you will see the monitor image from web camera via WiFi mobile phone. 3.5.3.3.2 3.5.3.3.2.1 Web Camera Recording Administrator Setup 77 Version 1.
MT4205 also can record the pictures from Webcam; only Administrator can activate the settings. Select Web Camera Server from main Menu and enable this function, click on Record Setting button for further setting. To set up the Webcam Advanced Configuration for each text field, the image from webcam will be recorded into your USB HDD or Remote FTP. Click on Apply after setup finished.
After click on Disk Explorer, you will see the folder screen appear including all the folders inside MT4205. (Below is the example.) For getting the images from web camera or any files inside router, you may copy the files into your own HDDs directly. In addition, all image files are stored in webcam_recorded_files folder, click to examine the content inside. 3.5.3.3.2.
After click on My Document, you will see folder screen appear as the example below. Notice: If you can’t open the folder, please check with administrator to set up your FTP access right. 3.5.4 Printer Server 80 Version 1.
MT4205 has two USB ports for connecting with printers to be shared on the local area network. Follow the steps to set up your PC to connect to a printer server. 1. Enable Printer Server: Check enable for applying printer server. 2. Enable Printer Access From WAN: Allow printer can access from WAN side by checking on enable for this item. 3. Printer Model: The printer model will be shown when the USB printer is plugged. 4. Printer Name: Enter the name you like. 5.
After setting USB printer on MT4205’s setup page, please go to Start > Printers and Faxes to add a printer. 【Step 2】 Click on Add a printer item. 【Step 3】 Click on Next button. 82 Version 1.
【Step 4】 Select Local printer attached to this computer, and click Next. 【Step 5】 Select Create a new port and choose Standard TCP/IP Port from drop-down list, then click Next. 83 Version 1.
【Step 6】 Click Next. 【Step 7】 Put in MT4205’s address: 192.168.1.1 and click Next. 84 Version 1.
【Step 8】 Select Custom and click on Settings… button to set the detail setting. 【Step 9】 Select LPR and give it the same Queue Name as USB Printer Name has shown, and mark LPR Byte Counting Enabled. Finally, click on Next button. 85 Version 1.
It has to be the same with the Printer Name as shown in section 3.5.4 Printer Server Configuration. 【Step 10】 Click Finish on the next screen after the aforesaid settings, you have to install the printer driver as well. 【Step 11】 Select the Manufacturer and Printers. If your printer is not listed in the table, please 86 Version 1.
insert its driver CD and then click on Have Disk… button for installation. Or click on Next button to finish the setting. You can name your printer, set it as default printer and share your printer as the next screen shown, the Printer Server setting is getting completed. 【Step 12】 It shows you the printer settings that you have specified, and then click Finish. 87 Version 1.
3.6 System Management MT4205 provides system management including password changing, firmware upgrade, time setting, user’s account setting and other detail settings. Following is detail explanation for each. 3.6.1 Reboot If you had entered the wrong configuration while setting up your router or other utilities, you can always reboot your MT4205 by this setting. It’s necessary to reboot the router if it begins working improperly, please click on Reboot button to reboot the router. 3.6.
1. Old Password: Enter the original password you set. 2. New Password: Enter the new password you want to change. 3. New Password (Confirm): Enter the new password again for confirming. 4. Apply & Cancel Click Apply to continue or Cancel to clear the settings on this page. 3.6.3 Firmware Upgrade There is certain risk while upgrading firmware. Upgrading firmware is not recommended unless the significant faulty is found. You can upgrade the firmware of MT4205 on this page.
1. Update Firmware: Click on Browse… button to search your local hard drive and locate the firmware to be used for update. 2. OK & Cancel Click OK to confirm or click Cancel to clear the setting on this page. Notice: Before using a whole new disk, please format it on your PC first, so that it can be formatted on MT4205. 3.6.4 Profile Sasve To back up the current configuration setting or load the backup data, also you can restore MT4205 to default setting by this function. 90 Version 1.
1. Save Settings To PC: Click on Save button for saving the configuration setting into assigned location. 2. Load Settings From PC: Click on ―Browse…‖ button for searching the saving configuration from hard drive, and then click on Load button to load all the settings into the router. 3. Restore To Factory Default Settings: After you have tried other methods for troubleshooting your network, you may choose to restore MT4205 to the factory default settings. 4.
1. HTTP Connection Port: The port number used to access the router. 2. Remote Management: You can allow any Internet IP address to access the router, or set up deny rule according to IP setting. 3. IP Address: Internet IP address of the computer that has access to the router. 4. Description: Enter the description for the remote configuration. 5. Add, Apply & Cancel Click on Add button to add the remote list, click on Apply button to activate, or click on Cancel button to clear the settings on this page. 6.
3.6.6 Time The System time is the time used by MT4205 for scheduling services. You can manually set the time or connect to a NTP (Network Time Protocol) server. If a NTP server is set, you will only need to set the time zone. If you manually set the time, you may also set Daylight Saving dates and the system time will automatically adjust on those dates. 1. Local Time: The default time within. 2. Default NTP Server: Select the NTP Server from the drop-down list. 3.
Click on Apply button to activate, or Cancel button to clear the settings. 3.6.7 UPnP Setting UPnP (Univsersal Plug and Play) allows users to connect their UPnP-enabled broadband router, printer server and other devices right to the network with zero-configuration, meaning easier setup for installing the device on the network.
1. Max Login User: Set up the maximum users to log in at the same time, select the number from drop-down list. If you want to change the maximum login users only without changing user’s information, please click on OK button after select login user’s number. 2. User Name: Create the user name in this blank. 3. Password: Set up the user’s password. 95 Version 1.
4. User Right: Check to allow set-user accessing Samba folder, monitoring from webcam or using FTP server. 5. Activated: Click On to allow the user’s right to be applied immediately. 6. Add, Apply & Cancel After finishing the above, click Add button to create user account. Click on Apply button to add set-user into the account list or Cancel button to clear the settings on this page. 7. User Account List The list shows all users’ names, passwords, status and rights. 3.6.
Notice: You have to click on Unplug button before removing the USB device from MT4205. 3.6.10 Email Alert To monitor router activity, you can run on a local PC or a remote one elsewhere on the Internet. And MT4205 provides the email alert facility so that the log messages can be packed as an e-mail for someone who wants to receive these messages by scheduled time. In the following, here explains how to set up the email alert function. 97 Version 1.
1. Email Alert: Check the enable box to activate the email alert service. 2. SMTP Server: Specify an IP address of the SMTP server which can send mails from your MT4205 to the recipients’ mailboxes directly. 3. Your Mail (from): Enter the email address indicated the sending location. 4. SMTP Auth: If the email alert needs to be sent via SMTP authentication, please check this item, and then enter the required account and password. 5. Account: Enter the email account from which you want to send the alert. 6.
11. Refresh & Delete Click on Refresh to renew the login data and other system status information, or click on Delete to clear these logs. 3.7 Log & Status MT4205 provides the log list, connection status and user’s account. 3.7.1 Network Configuration Network Configuration shows all connection status of LAN, WAN, Wireless and plugged USB devices. Each block shows configuration status, you may click Refresh to update the screen list.
3.7.2 User Account List This section shows all users’ information. Check the user name, status and opened directory/file on screen. 100 Version 1.
3.7.3 Event Log MT4205 provides system logs for review. The system status log shows logging time, type and detail information as below. Click Refresh to update. 3.8 Logout Click Logout on the bottom menu to exit and go back to GUI login home page as illustrated on page 23. 3.9 Personal Configuration Open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://192.168.1.1 (Default Gateway) into browser’s blank field. 101 Version 1.
Notice: If the homepage doesn’t appear, please check whether the TCP/IP configuration is obtaining IP address automatically or not. If you don’t know how to do this, please refer to 1.5 Get your IP Automatically & Manually. Homepage Click Personal Panel and log in with your own user account. (If you can’t access your personal account, please check with administrator for validation.
MT4205 provides personal control panel for every login user’s entrance to each application screen, please click on each icon for various applications. The icons appearing in gray color can’t be clicked if the user doesn’t have the right to use that function; even though there is none to be set, the user can still apply My Status. Notice: The available access rights are depended on administrator’s authorization in 3.6.8 User Account Management. 3.9.
Notice: If you can’t access Anonymous folder, please check with administrator to enable your FTP server rights. Files under this directory are only for downloading, but not for uploading, deleting, or edting. 3.9.2 My Document ―My Document‖ shows all the files in USB HDD under each user’s account. Login user can also create the folder or copy files into the HD directly via Internet. The illustrated below is the detail description of folder inside.
3.9.3 My Webcam ―My Webcam‖ application allows you to view the real time image when the web camera is on. Click My Webcam, and the system pops up a new window to display real time image as the example below shows. Notice: If you can’t view the real-time image, the cause may be the setting of Internet Security and needs to be adjusted, or to install the Java program. 3.9.4 My Status ―My Status‖ shows all the login information for your personal account.
Notice: All above usage information is based on administrator’s setup. 3.10 Site Map MT4205 provides site map clicking for each icon to carry out the easy setup from the home page. 106 Version 1.
Chapter 4 AP Mode 4.1 Administrator Quick Setup Instruction Make sure to switch the mode into AP Mode, then open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://192.168.1.254 (Default Gateway) into browser’s blank field. Notice: If the homepage doesn’t appear, please check whether the TCP/IP configuration is obtaining IP address automatically or not. If you don’t know how to do this, please refer to section 1.5 Get your IP Automatically & Manually.
User Name and Password The default values for User Name and Password are admin (all in lowercase letters). Click Login to enter. Notice: Only the password can be changed, please read setup 4.2.4 Password Setup or 4.5.2 Change Password. In order to protect your own settings, it’s strongly recommended to change the password before you finish the Router Basic Setup. 4.2 Quick Setup Typical Configuration Manager Page consists of two separate frames.
The above diagram shows all PCs and devices connected to your MT4205 and their status. Click Quick Setup on the left of the main menu. Then you’ll see the full functionality selection screen appears and detailed settings for each item, including ―Basic‖ and ―Application‖ two parts. Note: The device models named of USB Device, Webcam and Printer will be shown under the picture of each device if the product supports.
LAN Setup: Setup the IP Address for LAN and Group. If you are using the Router with multiple PCs on your LAN, you must connect the LAN via the Ethernet ports on the built-in Ethernet switch. You should also assign a unique IP address to each device residing on your LAN. Wireless Setup: Define the Wireless Mode, ESSID, TxRate, Channel and other wireless settings. Time Server Setup: Set time by NTP server or user define. Password Setup: To change administrator’s password.
1 and 253 that is not used by another device.) Please don’t change the default LAN IP settings at this section until after you have completed the rest of the configurations and confirm that your Internet connection is working. And the DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer; which means you must specify the starting and ending address of the IP address pool, and the DHCP Router’s address must be identical to the LAN IP’s IP address.
requests from unauthorized wireless clients. As the Encryption Type, select WEP or WPA can protect your data from eavesdroppers, if you do not need the encryption, select ―None‖ to skip the following setting. After checking each above and choose the suitable item by demand, click Next to proceed. Notice: If uses AP/Bridge to wirelessly connect to the router, here suggests disabling the DHCP in LAN Setup. Please refer to 4.2.1 LAN Setup. Select WDS from drop-down list. 6 is the default channel.
Moreover, WDS (Wireless Distribution System) is a Wireless Access Point mode that enables wireless bridging in which WDS APs communicate with each other only (without allowing for wireless clients or stations to access them), and/or wireless repeating in which APs communicate both with each other and with wireless stations (at the expense of half the throughput), please input the other party’s MAC address into the WDS column. 4.2.
4.2.5 USB Disk Management Setup Easy to check all the USB storage devices connected to your MT4205, view the entire data folder inside each storage device, and you can manage the disk formatting/partitioning via click on the button of this page. Select the USB Disk and click OK for refreshing all disks before you do disk partition, and the Unplug button will appear. To partition/format the disk, please select the disk and click Format.
Input the User’s name and password, and then click on “Add”, and you will see the user information appear on the “User Account List” Set each user’s right and space arrangement, and then click on Add button for saving user’s account. Click on Next button after finished. 4.2.7 FTP Server Setup MT4205 can be the FTP Server providing users to transmit files, also for the guest to download the files from assigned website.
4.2.8 Printer Server Setup MT4205 supports LPR-protocol, as well as NetBIOS, and is convenient for sharing printer. In other words, it is an Internet access solution for your LAN/WAN, which provides you the shared web surfing, and supports USB interface printer. Any users in the same subnet of MT4205 can print their document via the network printers. If the printer isn’t connected, you can’t choose “Enable”. Enable the printer and click on Next button to next setup.
Click on Next button to next setup. 4.2.11 Quick Setup Finish The Quick Setup has been completed successfully when you see this screen. To apply your new settings, please click on Finish button to reboot system automatically and go to the product’s diagram homepage. You may connect to Internet via wired or wireless at this moment according to above settings. 4.3 IP Configuration This function allows you to add routing rules into MT4205. It doesn’t provide functions of WAN and DDNS in AP mode, though.
1. IP Address The default value of LAN IP address is 192.168.1.254 for this router. 2. IP Netmask Fill in Subnet Mask, normally it is 255.255.255.0. 3. IP Gateway Fill in with the default gateway address. If you don’t know, please check your ISP. 4. DHCP Enable or disable DHCP services. DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer if enabled. 5.
8. Router This field indicates the IP address of DNS to provide to clients that request IP Address from DHCP Server, the default setting is the same with LAN IP address. 9. DNS This field indicates the IP address of DNS to provide to clients that request IP Address from DHCP Server, the default setting is the same with LAN IP address. 10. WINS Windows Internet Naming Service manages interaction of each PC on the Internet. If you use a WINS server, enter IP Address of server here. 11.
1. Wireless Select AP/Bridge or WDS to allow or disallow the wireless operation. 2. Wireless Mode This field indicates the 802.11g interface mode. ―802.11G‖ prevents the 802.11b clients from accessing the router. ―802.11B/G‖ allows both 802.11b and 802.11g clients to access the router. ―802.11B‖ will enable the network as an 802.11b wireless network. By default, the mode is ―802.11B/G‖. 3.
The 802.11g and 802.11b specification supports up to 14 overlapping Channels for radio communication. But only 11 Channels are supported in the United States and therefore built-in on MT4205. To minimize interference, configure each of MT4205 to use Non-overlapping channels. Non-overlapping channels have 25 MHz separation beginning at the first allowed channel for the country (for the US and most of Europe, channel 1, 6 & 11 are used.
Note: 128 bits WEP is most secure, but has more encryption/decryption overhead. Note that all wireless devices must support the same WEP encryption bit size and have the same key. Four keys can be entered here, but only one key can be selected at a time. The keys can be entered in ASCII or Hexadecimal. Select the item from drop-down list you wish to use. Pass phrase: Automatically generate four WEP keys.
Radius with 802.x: Check this circle to enable Radius client function. WPA Rekey Timer: Allows for the session keys to be refreshed over time, minimizing the amount of data that is encrypted with the same session key. RADIUS Server IP: The IP address of RADIUS server. RADIUS Server Port: The UDP port number that the RADIUS server is listed. The default value is 1812. Shared Secret: The RADIUS server and client share a secret that is used to authenticate the messages sent between them.
4.4.1 Samba Server By supporting NetBIOS Protocol, MT4205 provides LAN users to share files or printer via My Network Places. Click Samba Server to proceed. 1. Enable Samba Server Check to Enable/Disable while connecting. 2. Workgroup Name Fill in the name, and the default is Workgroup. 3. Server Name Name your server. 4. Server Description Describe your server by demand, and the default is Wireless Mobile Router. 5. Printer Model Printer model appears when connected. 6.
Please follow the steps below. 【Step 1】 Go to Start and click My Computer. 【Step 2】 Fill in blank address field with \\192.168.1.254. 【Step 3】 A window pops up asking for user name and password. If log in as an administrator, please enter admin for both fields; otherwise, fill in with personal account and password. Click OK after finished. 125 Version 1.
【Step 4】 As the window below appears, login user has entered file sharing directory, and the folders underneath are all available for sharing locally. Note: Only 2 icons show up at most. 1. If a USB flash drive/hard disk is connected and enabled, the samba folder shows up. 2. If a USB printer is connected and enabled, the printer icon shows up. 4.4.2 FTP Server By directly connecting USB storage devices to any USB port, FTP server can be created with simple configuration.
Only when USB storage device is plugged, FTP Server can be checked as enabled. 1. Enable FTP Server: The Enable for FTP Server only can be selected when USB storage device plugged. 2. Enable Anonymous to Login: Allow anonymous to login after check on enable. 3. Enable FTP Access from WAN: Allow FTP access from WAN side by checking on Enable for this item. 4. FTP Server Port: Define the FTP command transfer service port.
4.4.3.1 Web Camera Server Basic Setup 1. Enable Webcam Server: Allow using this function by checking on enable. 2. Access from WAN: Allow webcam can access from WAN side by checking on enable for this item. 3. Image format: The default is 320 x 240 pixels. 4. Preview: Click on this button, you can preview the image from webcam. 5. Record Setting: Please see the detail advance setting in 4.4.3.2 Web Camera Server Advanced Configuration. 6.
HDD or remote FTP; if select save to remote FTP, please continue following remote FTP setting. 4. USB HDD Directory: The section provides option of which folder should be used for saving webcam image. 5. Remote FTP URL: Input the FTP URL for saving webcam image. 6. Remote FTP port: Input the FTP port number under URL to save image. 7. Remote FTP user: Enter the user’s name you like and it will be used to save the webcam image into the FTP server. 8.
surveillance tools for home or office security; network Webcams are now being employed by early adopters for more personal matters, such as watching kids and monitoring pets. The Webcam can be remotely accessed and controlled via a browser. In addition, record and monitor live actions with USB webcam; then view the image through Internet browsers or WiFi mobile phones, such as 3G mobiles. 4.4.3.3.1.1 Web Camera Monitoring via WAN connection For viewing the image via WAN connection, see the diagram below.
【Step 2】 Enter the default value, admin, for both administrator’s name and password and log in the product’s main menu page. 【Step 3】 Click LAN under IP Config folder on the left side menu. Then set IP Address in the same subnet with upper-layer device, for example, 192.168.2.49; 192.168.2.1 for IP Gateway. After that, disable DHCP function and click Apply to save the settings. 131 Version 1.
【Step 4】 Click Remote Management under System Management directory and change HTTP Connection Port into 800. Click Apply to save the settings. 【Step 5】 Plug another internet wire into the WAN port and apply IP Release & Renew commands via command prompt window in order to obtain new IP address. Afterwards, open your web browser and fill in http://192.168.2.49:800/webcam.html into address field, so the login webpage shows up as below.
4.4.3.3.2 4.4.3.3.2.1 Web Camera Recording Administrator Setup MT4205 also can record the pictures from Webcam; only Administrator can activate the settings. Select Web Camera Server from main Menu and enable this function, click on Record Setting button for further setting. To set up the Webcam Advanced Configuration for each text box, the image from webcam will be recorded into your USB HDD or Remote FTP. Click on Apply after setup finished.
After click on Disk Explorer, you will see the folder screen appear including all the folders inside MT4205. (Below is the example.) For getting the images from web camera or any files inside router, you may copy the files into your own HDDs directly. In addition, all image files are stored in webcam_recorded_files folder, click to examine the content inside. 4.4.3.3.2.2 Personal Application 134 Version 1.
All the users under administrator’s setting can view webcam real-time images from My Webcam. Please log in with your own personal account. For viewing your own folder, please click “My Document”. After click on My Document, you will see folder screen appear as the example below. You can store files here, too. Notice: If you can’t open the folder, please check with administrator to set up your FTP access right. 135 Version 1.
4.4.4 Printer Server Follow the illustrations below to set up your MT4205 and USB-connected printer. 1. Enable Printer Server: Check enable for applying printer server. 2. Enable Printer Access From WAN: Allow printer can access from WAN side by checking enable for this item. 3. Printer Model: The printer model shows up while plugging a USB printer. 4. Printer Name: Enter the preferred name of your printer. 5. Printer Description: Enter the description of printer as your demand. 6.
After setting USB printer on MT4205’s setup page, please go to Start > Printers and Faxes to add a printer. 【Step 2】 Click on Add a printer item. 【Step 3】 Click on Next button. 【Step 4】 Select Local printer attached to this computer, and click Next. 137 Version 1.
【Step 5】 Select Create a new port and choose Standard TCP/IP Port from drop-down list, then click Next. 【Step 6】 Click Next. 【Step 7】 138 Version 1.
Put in MT4205’s address: 192.168.1.254 and click Next. 【Step 8】 Select Custom and click on Settings… button to set the detail setting. 【Step 9】 Select LPR and give it the same Queue Name as USB Printer Name has shown, and mark LPR Byte Counting Enabled. Finally, click on Next button. 139 Version 1.
It has to be the same with the Printer Name as shown in section 4.4.4 Printer Server Configuration. 【Step 10】 Click Finish on the next screen after the aforesaid settings, you have to install the printer driver as well. 140 Version 1.
【Step 11】 Select the Manufacturer and Printers. If your printer is not listed in the table, please insert its driver CD and then click on Have Disk… button for installation. Or click on Next button to finish the setting. You can name your printer, set it as default printer and share your printer as the next screen shown, the Printer Server setting is getting completed. 【Step 12】 It shows you the printer settings that you have specified, and then click Finish. 141 Version 1.
4.5 System Management MT4205 provides system management including password changing, firmware upgrade, time setting, user’s account setting and other detail settings. Following is detail explanation for each. 4.5.1 Reboot If you had entered the wrong configuration while setting up your router or other utilities, you can always reboot your MT4205 by this setting. It’s necessary to reboot the router if it begins working improperly, please click on Reboot button to reboot the router. 4.5.
1. Old Password: Enter the original password you set. 2. New Password: Enter the new password you want to change. 3. New Password (Confirm): Enter the new password again for confirming. 4. Apply & Cancel Click Apply to continue or Cancel to clear the settings on this page. 4.5.3 Firmware Upgrade There is certain risk while upgrading firmware. Upgrading firmware is not recommended unless the significant faulty is found. You can upgrade the firmware of MT4205 on this page.
1. Update Firmware: Click Browse to search your local hard drive and locate the firmware used for update. 2. OK & Cancel Click OK to confirm or Cancel to clear the setting on this page. Notice: Before using a whole new disk, please format it on your PC first, so that it can be formatted on MT4205. 4.5.4 Profile Save To back up the current configuration setting or load the backup data, also you can restore MT4205 to default setting by this function. 1.
4.5.5 Remote Management Remote Management allows MT4205 to be configured from the Internet by a web browser. In general, only a member of your network can browse the built-in web pages to perform ―Administrator‖ tasks. This feature enables you to perform the tasks from the remote (Internet) host. 1. HTTP Connection Port: The port number used to access the router. 2. Remote Management: You can allow any Internet IP address to access the router, or set up deny rule according to IP setting. 3.
4.5.6 Time The system automatically shows the local time and time on PC. You can set the date and time manually so that it can be adjusted on router accordingly. 1. Local Time: The default time within. 2. Set the Time: Select this item to set up time by manual, select the date and time from each drop-down list. 3. Set Time: Click Set Time to set local PC time on router. 4. Apply & Cancel Click Apply to activate or Cancel to clear the settings. 4.5.
1. Enable/Disable UPnP: Select to enable or disable this service. 2. Apply, Cancel Click Apply to activate this function or Cancel to clear the setting. 4.5.8 User Account Management Personal users can use each individual application such as My Status, My Webcam and My Document. This section is to set the user’s right. Also, all the users’ rights will be showed in User Account List and allowed to edit or delete by clicking the linking text. 147 Version 1.
1. Max Login User: Set up the maximum users to log in at the same time, select the number from drop-down list. If you want to change the maximum login users only without changing user’s information, please click on OK button after select login user’s number. 2. User Name: Create the user name in this blank. 3. Password: Set up the user’s password. 4. User Right: Check to allow the user accessing Samba folder, monitoring from webcam or using FTP server. 5.
1. Select the USB Disk and click OK for refreshing all disks before you perform disk partition, and the Unplug button appears afterwards. 2. To partition/format the disk, please select the disk and click on Format button. 3. Moreover, if you want to view the data inside the disk, please go to 4.2.7 FTP Sever Setup to enable FTP server and then click on Disk Explorer to view all the folders inside the device. Notice: You have to click on Unplug button before removing the USB device from MT4205. 4.5.
1. Email Alert: Check the enable box to activate the email alert service. 2. SMTP Server: Specify an IP address of the SMTP server which can send mails from your MT4205 to the recipients’ mailboxes directly. 3. Your Mail (from): Enter the email address indicated the sending location. 4. SMTP Auth: If the email alert needs to be sent via SMTP authentication, please check this item, and then enter the required account and password. 5. Account: Enter the email account from which you want to send the alert. 6.
7. Email Address (To): Enter the email address where to receive the alert. 8. Schedule: Arrange to send the alert when event happens or by regular time. 9. Add, Apply & Cancel After finishing the above, click Add to set up the rule into email alert list. Then, click Apply to save or Cancel to clear the settings on this page. 10. Email Alert List Display, edit or delete a list of relative information in regarding to the above mentioned. 11.
4.6.2 User Account List This section shows all users’ information. Check the user name, status and opened directory/file on screen. 4.6.3 Event Log MT4205 provides system logs for review. 152 Version 1.
The system status log shows logging time, type and detail information as below. Click Refresh to update. 4.7 Logout Click Logout on the bottom menu to exit and go back to GUI login home page. 4.8 Personal Configuration Open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://192.168.1.254 (Default Gateway) into browser’s blank field. Notice: If the homepage doesn’t appear, please check whether the TCP/IP configuration is obtaining IP address automatically or not.
Click Personal Panel and log in with your own user account. (If you can’t access your personal account, please check with administrator for validation.) Personal Panel Screen below shows every login user’s access rights, including Anonymous, My Document, My Webcam and My Status. 154 Version 1.
MT4205 provides personal control panel for every login user’s entrance to each application screen, please click on each icon for application. The icons appear in gray color can’t be clicked if the user doesn’t have the right to use that function; even though there is none to be set, the user can still apply My Status. Notice: The available access rights are depended on administrator’s authorization in 4.5.8 User Account Management. 4.8.
Notice: If you can’t access Anonymous folder, please check with administrator to enable your FTP server rights. Files under this directory are only for downloading, but not for uploading, deleting, or edting. 4.8.2 My Document ―My Document‖ shows all the files in USB HDD under each user’s account. Login user can also create the folder or copy files into the HD directly via Internet. The illustrated below is the detail description of folder inside.
4.8.3 My Webcam ―My Webcam‖ application allows you to view the real time image when the web camera is on. Click My Webcam, and the system pops up a new window to display real time image as the example below shows. Notice: If the image from webcam can’t be viewed, it may be caused by Internet security setting and needs to be corrected or installed with the Java program. 4.8.4 My Status ―My Status‖ shows all the login information for your personal account.
Notice: All above usage information is based on administrator’s setup. 4.9 Site Map MT4205 provides site map clicking for each icon to carry out the easy setup from the home page. 158 Version 1.
Chapter 5 Client Mode 5.1 Administrator Quick Setup Make sure to switch the mode into Client Mode, then open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://10.64.64.64 (Default Gateway) into browser’s blank field. Notice: If the homepage doesn’t appear, please check whether the TCP/IP configuration is obtaining IP address automatically or not. If you don’t know how to do this, please refer to section 1.5 Get your IP Automatically & Manually.
User Name and Password The default values for User Name and Password are admin (all in lowercase letters). Click Login to enter. Notice: Only the password can be changed, please read setup 5.2.4 Password Setup or 5.5.2 Change Password. In order to protect your own settings, it’s strongly recommended to change the password before you finish the Router Basic Setup. 5.2 Quick Setup Typical Configuration Manager Page consists of two separate frames.
The above diagram shows all PCs and devices connected to your MT4205 and their status. Click Quick Setup on the left of the main menu. Then you’ll see the full functionality selection screen appears and detailed settings for each item, including ―Basic‖ and ―Application‖ two parts. Note: The device models named of USB Device, Webcam and Printer will be shown under the picture of each device if the product supports.
Select the preferred AP for connection, for example, Storage_Fax_Server_Router as the above, and click Next to continue. 5.2.2 Wireless Setup Display connected wireless AP information. After setup completed, click Next. 162 Version 1.
5.2.3 Time Server Setup MT4205 shows local date and time; however, the time still can be changed manually by selecting from the drop-down list, which won’t effect the original time setting on your PC. After completed, click Next to proceed. 5.2.4 Password Setup Here suggests changing the password for logging into the configuration manager in terms of security reason. The password may consist of A-Z, a-z, 0-9, underscores, and a single dot (.
Easy to check all the USB storage devices connected to your MT4205, view the entire data folder inside each storage device, and you can manage the disk formatting/partitioning via click on the button of this page. Select the USB Disk and click OK for refreshing all disks before you do disk partition, and the Unplug button will appear. To partition/format the disk, please select the disk and click Format. Moreover, if you want to view the data inside the disk, please go to 5.2.
5.2.7 FTP Server Setup MT4205 can be the FTP Server providing users to transmit files, also for the guest to download the files from assigned website. Moreover, by connecting USB HDD, USB Flash to the router, user can easily set up a FTP Server to share or download files for local or remote users. If the USB device isn’t enabled first, you can’t enable FTP Server. (Not even click on “Enable”) Set the FTP Server and related setting. Disable the function as demand, and click Next to continue. 5.2.
shared web surfing, and supports USB interface printer. Any users in the same subnet of MT4205 can print their document via the network printers. If the printer isn’t connected, you can’t choose “Enable”. Enable the printer and click Next to continue. Notice: After above Printer Server in Quick Setup finished, the related printing settings on MT4205 and PC have to be set up, too. Please refer to 5.4.4 Printer Server to set the details. 5.2.
To apply your new settings, please click on Finish button to reboot system automatically and go to the product’s diagram homepage. You may connect to Internet wirelessly at this moment according to above settings. 5.3 IP Configuration This function allows you to add routing rules into MT4205, including LAN and Site Survey. 5.3.1 LAN Use this page to set up the local IP address and subnet mask for your router.
This field specifies the last address in the pool to be assigned by the DHCP server in your local network. The default setting is 75. 5. DHCP Clients List The list shows all clients’ IP and MAC addresses. 5.3.2 Site Survey Click Site Survey under IP Config directory. 1. Link Mode Select Infrastructure/Ad_hoc to enable wireless. 2. RTS Threshold This value should remain at its default setting of 2347.
4. SSID Name your wireless network, and the default is previously selected wireless AP. 5. bg Mode This field indicates the 802.11g interface mode. 802.11g prevents the 802.11b clients from accessing the router; 802.11b provides 802.11b standard wireless network. By default, the value is bg Mixed, which allows both 802.11b and 802.11g clients to access the router. 6. Rate Select the transmission rate up to 54Mbps for the network. The default setting is Auto. 7.
TKIP & AES PSK Key The applied algorithm is like WPA. However, WPA-PSK is using a simple code to generate the key, and the key length is 64 characters of Hex (0~9, a~f and A~F). 11. Apply & Cancel Click Apply to save or Cancel to clear the settings on this page. 5.4 Server MT4205 provides 4 server setups, including Samba Server, FTP Server, Web Camera Server and Printer Server. 5.4.
1. Enable Samba Server Check to Enable/Disable while connecting. 2. Workgroup Name Fill in the name, and the default is Workgroup. 3. Server Name Name your server. 4. Server Description Describe your server by demand, and the default is Wireless Mobile Router. 5. Printer Model Printer model appears when connected. 6. Apply & Cancel Click Apply to save or Cancel to clear settings. 5.4.1.1 How to Access File Sharing Directory Please follow the steps below. 【Step 1】 Go to Start and click My Computer.
【Step 2】 Fill in blank address field with \\10.64.64.64. 【Step 3】 A window pops up asking for user name and password. If log in as an administrator, please enter admin for both fields; otherwise, fill in with personal account and password. Click OK after finished. 【Step 4】 As the window below appears, login user has entered file sharing directory, and the folders underneath are all available for sharing locally. 172 Version 1.
Note: Only 2 icons show up at most. 1. If a USB flash drive/hard disk is connected and enabled, the samba folder shows up. 2. If a USB printer is connected and enabled, the printer icon shows up. 5.4.2 FTP Server FTP Server utility allows both local and remote users to upload or download files, pictures or MP3 music from the same storage device in most easy and timely fashion.
3. Enable FTP Access from WAN: Allow FTP access from WAN side by checking on Enable for this item. 4. FTP Server Port: Define the FTP command transfer service port. If you want to change this port number, also remember to change the service port setting of your FTP client. 5. Idle connection Time-Out: When a specific time value is added, FTP Server will be de-activated if it has no activity within the time limit. 6. Apply & Cancel Click Apply to continue or Cancel to clear the settings on this page. 7.
5.4.3.2 Web Camera Server Advanced Configuration Click Record Setting, and the screen below appears. 1. Enable save image: If you want to save the image from webcam, please check on enable. 2. Save image interval: For saving image, you can set the save interval time, the default value is 5 seconds. 3. Save Location: Set the save location for webcam image, you may save into USB HDD or remote FTP; if select save to remote FTP, please continue following remote FTP setting. 4.
5.4.3.3 5.4.3.3.1 Application for Web Camera Web Camera Monitoring Application Monitor your home or take pictures with a Webcam via MT4205; one can set up the monitoring or recording of all images into the USB HDD for reviewing. Often marketed as surveillance tools for home or office security; network Webcams are now being employed by early adopters for more personal matters, such as watching kids and monitoring pets. The Webcam can be remotely accessed and controlled via a browser.
Follow instructions below to set up WAN IP address. 【Step 1】 Click Network Configuration under the directory of Log & Status to check the selected wireless IP address, for example, 192.168.1.2 as below. 【Step 2】 Open web browser and fill http://192.168.1.1 into address field. The homepage of connected router with MT4205 shows up. Click Network Configuration under the directory of Log & Status to check its IP address, such as the example below. 177 Version 1.
【Step 3】 Click Virtual Server under the directory of NAT in Advance setup. Then check Enable and put 192.168.1.2 in Private IP field. Fill in 80 for both Private Port and Public Port, and then click Add. After completed, click Apply to save the setting. 【Step 4】 178 Version 1.
Plug internet wire into the WAN port and connect to your PC. Then open your web browser and fill in http://192.168.1.2/webcam.html into address field, so the login webpage shows up as below. 【Step 5】 After entering user name and password, the following monitor image shows up. 5.4.3.3.2 5.4.3.3.2.1 Web Camera Recording Administrator Setup MT4205 also can record the pictures from Webcam; only Administrator can activate the settings.
To set up the Webcam Advanced Configuration for each text box, the image from webcam will be recorded into your USB HDD or Remote FTP. Click on Apply after setup finished. For administrator, you may view all the images from webcam recording, please select Folder Management and click on Disk Explorer to view entire folder inside the disk including webcam record files. After click on Disk Explorer, you will see the folder screen appear including all the folders inside MT4205. (Below is the example.
For getting the images from web camera or any files inside router, you may copy the files into your own HDDs directly. In addition, all image files are stored in webcam_recorded_files folder, click to examine the content inside. 5.4.3.3.2.2 Personal Application All the users under administrator’s setting can view entire webcam real-time images from My Webcam. Please log in with your own personal account. For viewing your own folder, please click “My Document”. 181 Version 1.
After click on My Document, you will see folder screen appear as the example below. You can store files here, too. Notice: If you can’t open the folder, please check with administrator to set up your FTP access right. 5.4.4 Printer Server 182 Version 1.
Follow the illustrations below to set up your MT4205 and USB-connected printer. 1. Enable Printer Server: Check enable for applying printer server. 2. Enable Printer Access From WAN: Allow printer can access from WAN side by checking enable for this item. 3. Printer Model: The printer model shows up while plugging a USB printer. 4. Printer Name: Enter the preferred name of your printer. 5. Printer Description: Enter the description of printer as your demand. 6.
【Step 2】 Click on Add a printer item. 【Step 3】 Click on Next button. 【Step 4】 Select Local printer attached to this computer, and click Next. 184 Version 1.
【Step 5】 Select Create a new port and choose Standard TCP/IP Port from drop-down list, then click Next. 【Step 6】 Click Next. 185 Version 1.
【Step 7】 Put in MT4205’s address: 10.64.64.64 (as in Client Mode) and click Next. 【Step 8】 Select Custom and click on Settings… button to set the detail setting. 【Step 9】 Select LPR and give it the same Queue Name as USB Printer Name has shown, and mark LPR Byte Counting Enabled. Finally, click on Next button. 186 Version 1.
It has to be the same with the Printer Name as shown in section 5.4.4 Printer Server Configuration. 【Step 10】 Click Finish on the next screen after the aforesaid settings, you have to install the printer driver as well. 【Step 11】 Select the Manufacturer and Printers. If your printer is not listed in the table, please insert its driver CD and then click on Have Disk… button for installation. Or click on Next button to finish the setting. 187 Version 1.
You can name your printer, set it as default printer and share your printer as the next screen shown, the Printer Server setting is getting completed. 【Step 12】 It shows you the printer settings that you have specified, and then click Finish. 188 Version 1.
5.5 System Management MT4205 provides system management including password changing, firmware upgrade, time setting, user’s account setting and other detail settings. Following is detail explanation for each. 5.5.1 Reboot If you had entered the wrong configuration while setting up your router or other utilities, you can always reboot your MT4205 by this setting. It’s necessary to reboot the router if it begins working improperly, please click on Reboot button to reboot the router. 5.5.
1. Old Password: Enter the original password you set. 2. New Password: Enter the new password you want to change. 3. New Password (Confirm): Enter the new password again for confirming. 4. Apply & Cancel Click Apply to continue or Cancel to clear the settings on this page. 5.5.3 Firmware Upgrade There is certain risk while upgrading firmware. Upgrading firmware is not recommended unless the significant faulty is found. You can upgrade the firmware of MT4205 on this page.
1. Update Firmware: Click Browse to browse the local hard drive and locate the firmware used for update. 2. OK & Cancel Click OK to confirm or Cancel to clear the setting on this page. Notice: Before using a whole new disk, please format it on your PC first, so that it can be formatted on MT4205. 5.5.4 Profile Save To back up the current configuration setting or load the backup data, also you can restore MT4205 to default setting by this function. 1.
configuration from hard drive, and then click on Load button to load all the settings into the router. 3. Restore To Factory Default Settings: After you have tried other methods for troubleshooting your network, you may choose to restore MT4205 to the factory default settings. 4. Apply Click on Apply button to save the settings. 5.5.5 Remote Management Remote Management allows MT4205 to be configured from the Internet by a web browser.
2. Remote Management: You can allow any Internet IP address to access the router, or set up deny rule according to IP setting. 3. IP Address: Internet IP address of the computer that has access to the router. 4. Description: Enter the description for the remote configuration. 5. Add, Apply & Cancel Click Add to add the remote list, and click Apply to activate, or Cancel to clear the settings on this page. 6.
1. Local Time: The default time within. 2. Set the Time: Select this item to set up time by manual, select the date and time from each drop-down list. 3. Set Time: Click Set Time to set local PC time on router. 4. Apply & Cancel Click Apply to activate or Cancel to clear the settings. 5.5.7 UPnP Setting UPnP (Univsersal Plug and Play) allows all devices on the network to connect by node-to-node via TCP/IP protocol. 1. Enable/Disable UPnP: Select to enable or disable this service. 2.
1. Max Login User: Set up the maximum users to log in at the same time, select the number from drop-down list. If you want to change the maximum login users only without changing user’s information, please click on OK button after select login user’s number. 2. User Name: Create the user name in this blank. 3. Password: Set up the user’s password. 4. User Right: Check to allow set-user accessing Samba folder, monitoring from webcam or using FTP server. 5.
7. User Account List The list shows all users’ names, passwords, status and rights. 5.5.9 Folder Management Easy to check all the USB storage devices connected to MT4205, view the entire data folder inside each storage devices, and you can manage the disk formatting / partition via clicking the button on this page. 1. Select the USB Disk and click OK for refreshing all disks before you perform disk partition, and the Unplug button appears afterwards. 2.
5.5.10 Email Alert To monitor router activity, you can run on a local PC or a remote one elsewhere on the Internet. And MT4205 provides the email alert facility so that the log messages can be packed as an e-mail for someone who wants to receive these messages by scheduled time. In the following, here explains how to set up the email alert function. 1. Email Alert: Check the enable box to activate the email alert service. 197 Version 1.
2. SMTP Server: Specify an IP address of the SMTP server which can send mails from your MT4205 to the recipients’ mailboxes directly. 3. Your Mail (from): Enter the email address indicated the sending location. 4. SMTP Auth: If the email alert needs to be sent via SMTP authentication, please check this item, and then enter the required account and password. 5. Account: Enter the email account from which you want to send the alert. 6. Password: Enter the email account password to validate. 7.
5.6.2 User Account List This section shows all users’ information. Check the user name, status and opened directory/file on screen. 5.6.3 Event Log MT4205 provides system logs for review. 199 Version 1.
The system status log shows logging time, type and detail information as below. Click Refresh to update. 5.7 Logout Click Logout on the bottom menu to exit and go back to login home page. 5.8 Personal Configuration Open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://10.64.64.64 (Default Gateway) into browser’s blank field. Notice: If the homepage doesn’t appear, please check whether the TCP/IP configuration is obtaining IP address automatically or not.
Homepage Click Personal Panel and log in with your own user account. (If you can’t access your personal account, please check with administrator for validation.) Personal Panel Screen below shows every login user’s access rights, including Anonymous, My Document, My Webcam and My Status. 201 Version 1.
MT4205 provides personal control panel for every login user’s entrance to each application screen, please click on each icon for application. The icons appear in gray color can’t be clicked if the user doesn’t have the right to use that function; even though there is none to be set, the user can still apply My Status. Notice: The available access rights are depended on administrator’s authorization in 5.5.8 User Account Management. 5.8.
Notice: If you can’t access Anonymous folder, please check with administrator to enable your FTP server rights. Files under this directory are only for downloading, but not for uploading, deleting, or edting. 5.8.2 My Document ―My Document‖ shows all the files in USB HDD under each user’s account. Login user can also create the folder or copy files into the HD directly via Internet. The illustrated below is the detail description of folder inside.
5.8.3 My Webcam ―My Webcam‖ application allows you to view the real time image when the web camera is on. Click My Webcam, and the system pops up a new window to display real time image as the example below shows. Notice: If the image from webcam can’t be viewed, it may be caused by Internet security setting and needs to be corrected or installed with the Java program. 5.8.4 My Status ―My Status‖ shows all the login information for your personal account.
Notice: All above usage information is based on administrator’s setup. 5.9 Site Map MT4205 provides site map clicking for each icon to carry out the easy setup from the home page. 205 Version 1.
Chapter 6 DDNS Service Application DDNS is a service changes the dynamic IP to the static IP. The settings of DDNS can solve the problem of being given the different IP by router every time. After setting the Router, your host name would correspond to your dynamic IP. Moreover, via the host name application, it could be easier for you to use FTP, Webcam and Printer remotely. Dynamic DNS allows you to make an assumed name as a dynamic IP address to a static host name. Please configure the dynamic DNS below.
Version 1.
【Step 3】 When you got this account created message, close it, and check your mailbox. You would get a mail from DynDNS website. 【Step 4】 Click on the indicated address within your mail to confirm. 【Step 5】 Click on login. 【Step 6】 Click My Services after logging in. 208 Version 1.
【Step 7】 Click Add New Hostname. 【Step 8】 Put in your favorite hostname and service type, and then click Create Host after finished. 209 Version 1.
【Step 9】 Your hostname has been created when you see the following page. Chapter 7 Q & A 7.1 Installation 1. Q: Where is the XDSL Router installed on the network? A: In a typical environment, the Router is installed between the XDSL line and the LAN. Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub (switch or computer). 2. Q: Why does the throughput seem slow? A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter.
A: In case MT4205 is inaccessible, you can try to restore its factory default settings. Please press the ―Reset‖ button and keep it pressed for over 7 seconds and the light of STATUS will vanish. The LEDs will flash again when reset is successful. 3. Q: Why does MT4205 shut down unexpectedly? A: Re-plug your power adapter. Then, check the STATUS indicator; if it is off, the internal flash memory is damaged. For more help, please contact with your provider. 7.3 IP Address 1.
A: It’s possible that your Internet protocol (TCP/IP) was set to use the following IP address. Please do as the following steps. (Windows 2000 & XP) Start＞Settings＞ Network and Dial-up Connections＞double click on Internet Protocol(TCP/IP)＞ select obtain IP address automatically＞ Click on OK button. Then, open Internet browser for testing. If you still can’t go online, please test something else below. Verify network configuration by ensuring that there are no duplicate IP addresses.
2. Select never dial a connection, click on Apply button, and then click on OK button. 3. Click on Tools and then click on Internet Options. 4. Click on Connections and then click on LAN Settings. 5. Make sure none of the check boxes are selected and click on OK button. 6. Click on OK button. Netscape Navigator Users: 1. Click on Edit > Preferences > double-click Advanced in the Category window. 2. Click on Proxies > select Direct connection to the Internet > click on OK button. 3.
Rule1: After connecting USB devices, please reboot your Router. Rule2: Before finishing the DHCP setup, please don’t connect any computer to LAN ports, because the conflict of having the same IP may occur and cause some computers a lot of trouble. ※Notice: Make sure that you always click on the Apply button after configuring each setting. And in order to let other LAN ports work properly, please reboot your PC. 3. Q: I don’t know how to configure DHCP. A: DHCP is commonly used in the large local network.
A: Check the DNS server settings on your PC. You should get the DNS servers settings from your ISP. If your PC is running a DHCP client, remove any DNS IP address setting. As the router assign the DNS settings to the DHCP-client-enabled PC. 7. Q: MT4205 couldn’t save the setting after click on Apply button? A: MT4205 will start to run after the setting finished applying, but the setting isn’t written into memory.
Next make sure the router and the NIC are configured to use the same communications channel. There are normally 11 of them, and the default channel can also vary from vendor to vendor. You might also want to confirm that the router has DHCP services enabled and an address pool configured. If not, the NIC won't be able to pick up an IP address. I have run across a few access points that offer DHCP services but do not assign all of the needed IP information to the NIC.
A: The wireless system will connect at highest possible speed, depending on the distance and the environment. To obtain the highest possible connection speed, you can experiment with following: Access Point location: Try adjusting the location and orientation of the Access Point. Wireless Channel: If interference is the problem, changing to another channel may show a marked improvement. Radio Interference: Other devices may be causing interference.
6. Q: The WinXP wireless interface couldn’t communicate the WEP with MT4205’s wireless interface. A: The default WEP of WinXP is Authentication Open System - WEP, but the WEP of MT4205 is only for Shared Key - WEP, it caused both sides couldn’t communicate. Please select the WEP of WinXP from Authentication Open System to Pre-shared Key - WEP, and then the WEP wireless interface between WinXP and MT4205 would be communicated. 7.7 Samba Server 1.
then the user can start to use the function of MT4205. 4. Q: How to remove or revise the files on FTP server? A: If there is any file needing to be revised, here suggests downloading the file to the HDD of PC and modifying it locally. Then upload to FTP server again after revised. 7.9 Webcam Server 1. Q: I cannot view Webcam’s video screen from WAN. A: Please follow the steps below. Step1. Open Internet browser and enter http://192.168.1.1 in the address field. Step2.
6. Q: Why couldn’t the image of USB Webcam be seen from WAN? A: Besides making sure to enable the USB Webcam Access from WAN, the Remote Management should be enabled as well, so that the image of USB Webcam could be seen from WAN. 7.10 Printer Server 1. Q: Why can’t my printer work? A: For more details, please refer to Chapter 3.5.5 Print Server in the USB Application. Maybe MT4205 doesn’t support your printer. You can contact with us to get more updated information about printer driver support. 2.
7.12 Others 1. Q: Why can’t I receive corrupted FTP downloads? A: If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP program. 2. Q: Why does the router dial out for PPPoE mode very often? A: Normally some of game, music or anti-virus program will send out packets that trigger the router to dial out, you can close these programs. Or you can set the idle time to 0, then control to dial out manually. 3.
8.2 Web Camera MT4205 supports OV511, OV511+, OV518, OV518+, SAA8115HL and SAA8116HL chipsets; besides, adding spca5xx/LE driver into firmware as the table below shows.
Lifetec LT 9388 OV511 Logitech Logitech QuickCam 3000 Pro QuickCam 4000 Pro SAA8116HL SAA8116HL Logitech QuickCam Orbit/Sphere SAA8116 Maitech AWK-300 OV511+ Maxxtro CAM22U OV511 Maxell Maxcam (MPCC-1) OV511 Medion MD9388 OV511+ MediaForte MV300 OV511 MediaForte PC Vision 300 OV511 WCam 3X OV511 Mtekvision Zeca MV402 OV511+ OmniVision OV7110 Eval Board OV511 OmniVision OV511+/OV7120 Eval Board OV511+ OmniVision OV511+/OV7620 Eval Board OV511+ Pretec PCC-600 OV511
Terratec TerraCam PRO OV511+ Terratec TerraCam USB PRO OV511+ Waytech I-Pac VIC-30 OV511+ Webeye 2000B OV511+ Vendor Name Driver Product Name Spca5xx/LE Aiptek Aiptek PocketDVII1.
Creative WebCam Live! Motion -- Creative WebCam Live! Ultra -- Creative WebCam Live! Ultra for Notebooks -- Creative Webcam Mobile Zc0301P Creative Webcam NoteBook Zc0301P Digital Dream Enigma 1.3 spca504b Digital Dream Epsilon 1.3 spca533a Generic Generic vimicro 303b -- Generic Generic Zc0305b -- Genius Dsc-1.
Logitech QuickCam Chat zc030x Logitech QuickCam IM zc030x Logitech QuickCam IM zc030x Logitech QuickCam IM zc030x Logitech QuickCam IM/Connect zc030x Logitech QuickCam IM+Sound zc030x Logitech QuickCam tor Notebook zc030x Megapix Megapix V4 spca533a Mercury Cyberpix S550V -- Mercury Peripherals Inc. -- MercuryDigital Mercury Digital Pro 3.
A-DATA My Flash PD1 (512MB) USB2.0 Zynet PD-A2 USB 2.0 Maxtor DiamondMax Plus8 USB 2.0 Kingston Data Traveler 2.0 Shuttle SFD-0128 Apacer HandyDrive PQI I-Ststick 32MB Apacer Handy Steno 64MB ASUS AI-flash 2 64MB ASUS 32MB GENUINE 32MB USB 1.1 NEXS SD card Transcend JetFlash 128 MB USB 2.0 SanDisk Curzer Mini Flash 256MB USB 2.0 PQI Cool Drive(U339) 128 MB USB 2.0 KingMax 128MB Kinggaroo SONA 128MB USB 1.0 USB 2.0 2. External Hard Drive Vendor Name Model No.
3. Safari ver. 2.0.4 or higher version 8.6 Easy Setup MicroSoft: Windows 2000, XP, Vista 8.7 Communications Regulation Information Should any consumers need to learn more information, services and supports, please contact the supplier of your product directly. 228 Version 1.
