Specifications

SET UP - Basic Programming
Thefollowing6programmingstepsmustbedonepriortooperatingtheGT-TLI.
Disabling / Enabling Door Calling Telephone
TheGT-TLIcanbedisabledfromcallingtheprogrammedtelephone,incaseswherethetenantwishesnottobe
disturbedbytheGTentrancepanel.ThedefaultsettingiswithDoorCallActivationenabled.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter
⃰
toenable,or# to disable
• “Thecodeenterediscorrect”willbeplayed,andtheGT-TLIwillgointoidlemode
Ring Duration of Locally Connected Telephone
Settheringdurationfortheconnectedtelephone(s).Timesetmustbebetween10-45seconds.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 20-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=timeinseconds,i.e.30)
Program Remote Call Number
SettheremotetelephonenumberthatwillbedialedbytheGT-TLI.Thetelephonenumbercanbeupto16digitslong.
Ifthetelephonenumberislessthan16digits,press#afterthelastdigit.A"
⃰
“canbeusedwhenapauseisrequired.
Forexample,ifneedingtodialadigitpriortoaccessinganoutsidephoneline,orifdialingaphonenumberwithan
extension,usethe“
⃰
“forapause.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 21-1longbeepwillbeplayed
• Enter nn #-“Thecodeenterediscorrect”willbeplayed(nn=telephonenumber)
To delete a telephone number.
• Enter program access code
⃰
2001# -“Thecodeenterediscorrect”willbeplayed
• Enter 21-1longbeepwillbeplayed
• Enter #-“Thecodeenterediscorrect”willbeplayed
Program DTMF Code for GT Entrance Panel
InorderforthetelephonetoactivatethedoorreleasecontactontheGTentrancepanel,a2-digitaccesscodemust
beenteredonthetelephonewhileincommunicationwiththedoorstation.Thedefaultcodeis10.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 25-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=2digitaccesscode)
Program DTMF Code for GT-TLI Secondary Dry Contact
InorderforthetelephonetoactivatethesecondarydrycontactontheGT-TLI,a2-digitaccesscodemustbeentered
onthetelephonewhileincommunicationwiththedoorstation.Thedefaultcodeis20.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 30-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=2digitaccesscode)
Program Duration of GT-TLI Secondary Dry Contact
ThesecondarydrycontactontheGT-TLIcanbeactivatedforadurationof1-10seconds.Thedefaultis5seconds.
• Enter program access code
⃰
2000# -“Thecodeenterediscorrect”willbeplayed
• Enter 32-1longbeepwillbeplayed
• Enter nn-“Thecodeenterediscorrect”willbeplayed(nn=timeinseconds,2digits)
When programming is complete dial 00 toexitprogrammingmode.
8 | GT-TLI Installation / Operation Instructions