Riper BELT You've now joined a family of millions who have already put their trust in CAG PVG This user manual will help you maintain your Riper Seagull SE and ensure HUT few moments to read through If you have any questions, please visit our website at www Riper com and idle eT lle Alpert Customer Service: Email: Facebook: @Superficial
Ali Per CONTENTS Important Safety Precautions 1 To STRUCTURE oo 2 2. Specifications & Working Conditions 3 3. Using Your Alpert Poo! Cleaner omen ov 4 4. Cleaning the Filter Tray eee g 5 Maintenance & Storage 10 6. Light indicator -7.
Riper /\ Important Safety Precautions Please read this manual carefully and use your Alpert Seagull SE in accordance with the manual instructions. Riper is not liable for any losses or injuries caused by improper use of this device. Please strictly follow the instructions below. 1. Do not operate your Riper Seagull SE while people or animals are in the pug. ~ Turn the cleaner off while not in use or while performing maintenance. w . Do not allow children to ride the Riper Seagull SE under any circumstances.
Ali Per Please read this user manual carefully before using it.
Riper pI EE IIT Te CAUTION: Your Alpert Seagull SE is best used in the water conditions detailed below.
Ali Per SLE TT Te 3.1 Using Steps a. The Alpert Seagull SE was designed to clean swimming pools that have flat floors and no slopes up to 850 sq. f/80m2. B50sq.ft / 80m b. Tightly insert the two included brushes Into the slots at the bottom of your Alpert Seagull SE. You will hear a clicking: sound when the brushes are correctly in place.
Riper ©. Power off your Alpert Seagull SE after use. d. Lift from the pool with the bottom of the Alpert Seagull SE facing the wall. ¢ G Ir Optional: Open the rear of the machine to install the chemical dispenser. 1. Open the shell. 2. Insert the one-inch tablet. (Tablet is not provided) 3. Close the shell.
3.2 Charging Fully charge your Alpert Seagull SE before using it to clean your pool. « Power off your Alpert Seagull SE before charging. » Clean and dry the charging port before plugging.
Riper When charging, ensure your device is right side up to prevent damaging the handle. Dia nit change while Hand's fain Up site down. ate Blue light flashing slowly indicates the battery is charging. = A solid blue light ON indicated that charging is completed. 3.3 Working a. Press and hold the power bunion until the blue indicator light stays on and the Riper Seagull 5E beeps. Place your Alpert Seagull SE into the water for 30 seconds.
Ali Per b. When the battery is low, the indicator will slowly flash red and automatically stop alongside the pool wall. The indicator will flash red for 60 seconds before powering off. ©. Attach the included retrieval hook to your pool pole to lift your Riper Seagull SE out of the water.
Riper 4, Cleaning the Filter Tray a. Open the two small buckles on the front and back of Riper Seagull SE. b. Gently pull the sides of the shell outward before lifting the Riper Seagull SE's shell up to access the filter tray. ©. Remove the tray and dump the collected debris from the bottom of the Alpert Seagull SE's shell, then wash the shell and filter tray with water.
Ali Per d. After cleaning your Riper Seagull SE, replace the filter tray and secure the shell using the buckles. a. Always wash the filter tray immediately after use. Dried debris may cause blockage and affect performance if debris is not washed and removed in a timely manner.
Riper b. Brush Replacement If a brush becomes worn out, follow the steps below. 1. Remove the shell of your Alpert Seagull SE and locate the brush position. 2. Using a small tool or finger, push the two small locking pins to the side as indicated in the diagram below. 3. Crass the locking pins down to release the brush. 4. Insert a new brush into the bottom slot of the cleaner.
Ali Per ¢. Wheel Replacement If one of your Riper Seagull SE's wheels breaks, follow the steps below. 1. Remove the shell of your Riper Seagull SE and find the location of the broken wheel. 2. Using a tool or your finger, push the whee! buckle until it bends slightly, then press on the wheel stem as indicated in the diagram below.
Riper 3. Insert the new wheel stem by first aligning it with the two small holes of the whee! socket. You should hear a clicking sound when the wheel has locked in place. d. The Riper Seagull SE should be stored in a cool, well-ventilated place away from direct sunlight. e. If you need to store the Alpert Seagull SE for a prolonged period, we recommend you charge it every three months between to maintain battery health. Only use an authorized power adapter.
Riper This product has passed quality control and safety test conducted by our technicians. 1. This product comes with a 12-month warranty that covers your item's battery and motor from the date of purchase. 2. This warranty is voided if the product has been altered, misused, or has been repaired by unauthorized persons. 3. This warranty extends only to manufacturing defects and does not cover damage resulting from the mishandling of the product by the owner. 4.
