ROBOTIC POOL CLEANER User Manual Orca 800 Mate
Thank you for choosing Aiper robotic pool cleaner. You have joined millions of people to enjoy the convenience of robotic pool cleaning. This user manual helps you to keep your robot performing at its best. Please take a few moments to read through it. If you have any questions, please contact our customer service for assistance or visit www.aiper.com for more information. Aiper Customer Service Customer Service Number: US Toll Free: 1-866-850-0666 Email: service@aiper.
CONTENTS Important Precautions ----------------------------- 1 1. Introduction ------------------------------------- 2 2. Structure ---------------------------------------- 2 3. Specifications ----------------------------------- 3 4. Operations -------------------------------------- 3 Attentions ------------------------------------------ 3 4.1 Control Panel and Indicator Instructions ------ 5 4.2 Functions & Adjustments of Nozzles ---------- 6 4.3 Filter Cleaning ---------------------------------- 7 5.
Important Precautions 1. Read the manual carefully, and use the cleaner according to the manual. We are not liable for any losses or injuries caused by improper use. 2. To avoid any accidents/damages, please fix the power supply unit 11.5ft (3.5m) away from the swimming pool by using the included safety rope, in case it falls into the water and result in potential danger. 3. To prevent severe damages to the cleaner, never power on the unit when it is outside of the swimming pool. 4.
15. Do not operate the cleaner when there are people or animals in the pool. 16. Take the cleaner out of the swimming pool after use. If the cleaner is immersed in the water for a long time, there will be micro organisms produced. 17. The cord should be untwisted and wrapped properly after use. 18. Use the original adapter only for the control box kit. 19. Do not operate the cleaner while pool filter is running. 20. Do not allow children to ride on the cleaner or play with it. 1.
3. Specifications 1. Model Orca 800 Mate 2. Rated Input Voltage 110V~120V, 60Hz 3. Rated Working Voltage DC 17V 4. Power 150W 5. Optional Working Cycles 1H/2H/3H 6. Pool Size Up to 33ft(10m) 7. Filter Capacity 79GPM (300LPM) 8. Filter Density 180μm 9. Moving Speed 32.8ft/min (10m/min) 10. Waterproof Grade IPX8 for the cleaner; IPX5 for the power supply unit 11. Pool Water Temperature 50°F~95°F (10℃~35℃) 12. Pool Water PH Value 7.0~7.4 13. Max Water Depth 8.2ft (2.5m) 14.
2. When pulling the cleaner out of the water, suspend the cleaner on the water for about 10-15 seconds to empty the water inside. Please hold the top handle only; never pull the cable. 3. Please install the swing plate and brush before use for normal working. 4. Please use the included safety rope to fix the power supply unit away from the pool in case it falls into the water.
4.1 Control Panel and Indicator Instructions No. Sign Instruction Function description Press this button, the cleaner is power-on. 1 ON/OFF Power on/off Press a second time, the cleaner is off.
4.2 Functions & Adjustments of Nozzles There are two nozzles on the cleaner, one of them opens when the other closes. Water flows out through the open nozzle to thrust the cleaner to move forward. Adjust the nozzle by turning it to control the moving route. a. Settings of nozzle angle and moving route Sketch: the nozzles of the cleaner are marked with angles (0°-40°). The cleaner moves in an approximately straight line when the nozzle angle is 0°.
Setting Three: 20°--20°, for round pools Nozzle Angle Moving Route Note: These are recommended settings and different settings might apply to specific pools. So the operator can adjust the settings according to the principle of nozzle settings and the actual situation of the pool. 4.3 Filter Cleaning A.
B. Take out the filter tray C. Wash the filter tray and chassis D. Reassemble the cleaner and clip on 5. Trouble Shooting Remark: The pool water condition must be within the following parameters: • PH: 7.0 —7.
The robot does not reach all pool areas The robot does not work The power supply unit is improperly positioned Place the power supply unit at a proper position to reach all pool areas There is algae on the pool floor and it can’t be cleaned since it floats easily after the machine passes by Before using the cleaner, please clean the algae on the floor or walls in case it floats when the machine passes by The pool shape is not regular The ideal pool shapes are ROUND, OVAL, RECTANGULAR, KIDNEYLIKE.
6. Packing List Item Orca 800 Mate Quantity (PC) Name Cleaner with 33ft Cable 1 Power Supply Unit 1 User Manual 1 Safety Rope 1 7. Warranty 1.This product is covered by Aiper warranty for 24 months ( only for driving kit and control box kit) from the date of purchase. Consumable parts are beyond warranty which include Filter Tray/Brush/ Wheels/Nozzles. 2. This warranty is voided if the product has been altered, misused, or has been repaired by unauthorized personnels. 3.
Aiper Customer Service: US Toll Free: 1-866-850-0666 Email: service@aiper.
