User's Manual

1
2
3
6
7
5
75
8
9
10
6
4
CHAPTER I – PRESENTATION
1.1 PRESENTATION
Aimpoint’s Reex Sights are rugged precision electronic optical red dot sights
developed for civilian, military and law enforcement applications.
Aimpoint sights are designed for the ”two eyes open” method of sighting, which
greatly enhances situational awareness and target acquisition speed. Thanks
to the parallax-free design, the dot follows the movement of the user’s eye
while remaining xed on the target, eliminating any need for centering. Further,
the sight allows for unlimited eye-relief.
The CompM3 is compatible with 1st , 2nd and 3rd generation night vision
devices, while the CompML3 is optimized for applications, which do not require
night vision compatibility.
The CompM3 and CompML3 sights are using the revolutionary Advanced
Circuit Efciency Technology, ACET. ACET combines Aimpoint’s superior
accuracy and ease of use with signicantly low power usage.
1.2 SPECIFICATION
Material – housing: Extruded, high strength aluminum, anodized
Material – rubber cover: Chloroprene rubber (MIL-R-6855)
Material – lens covers: Thermoplastic elastomer, black, non-glare
Surface nish: Hard Anodized, Dark Graphite Grey, matte
Rubber cover: Black or Dark Earth Brown
Optical magnication: 1X
Eye relief: Unlimited, no centering required
Optical coating: Anti Reex coating, all surfaces, Multi-layer
coating for reection, Band Pass coating for
NVD* compatibility (CompM3)
Dot size: 2 and 4 MOA**
dot brightness: CompM3: 10 positions: 4 NVD, 6 daylight
settings of which 1 Extra Bright
CompML3: 10 positions: 1 Off, 9 daylight of
which 1 Extra Bright
Battery: One 3V Lithium battery type 2L76 or DL1/3N
Battery life*** (hours): 50 000 h on setting 7 of 10,
Typically 500 000 h at NVD setting.
Length (incl. lens covers): 130 mm (5.1”)
Width: 62 mm (2.4”), incl rubber cover,
49 mm (1.9”) without
Height: 58 mm (2.3”), incl rubber cover,
49 mm (1.9”) without
Weight: 270 gram (9.5 oz), incl rubber cover,
220 gram (7.8 oz) without
Adjustment: Range ±2 m at 100 meters, in windage and
elevation 1 click = 13 mm at 80 meters =
16 mm at 100 meters = 1/2” at 100 yards.
Mounting: One wide ring, 30 mm, or Aimpoint QR Ring
Max temperature range: -45 ºC to +70 ºC (-50 ºF to +160 ºF)
Water resistance: Submersible to 45 m (135 ft) water depth
*NVD: Night Vision Device
**MOA: Minute Of Angle 1MOA ≈ 30 mm at 100 meters ≈ 1” at 100 yards
***Average values, depending on brightness setting
CHAPTER II – OPERATION UNDER NORMAL CONDITIONS
2.1 ASSEMBLY AND PREPARATION FOR USE
WARNING: Ensure that the weapon is unloaded and the safety selector
is in the ”safe” position before attempting to install, remove or perform
maintenance on the sight.
2.1.1 Installing Battery
a. Remove Battery cap (2) by turning it counter clockwise.
b. Insert Battery (3) with positive (+) end toward Battery cap (2).
CAUTION: When replacing battery check that the O-ring is present and not
damaged. Failure to do so could result in water leakage into the battery
compartment.
c. Install Battery cap (2) by turning clockwise until snug. Hand tighten only.
Using tools could damage equipment.
d. Verify that red dot is present by turning the Rotary switch (4) clockwise.
2.1.2 Installing Ring and Sight on the weapon
Aimpoint’s sights are designed for installation on most types of weapons.
If your weapon does not have or support an appropriate base(s), please
consult your dealer, gunsmith or other qualied source.
a. Assemble the sight to the weapon by using Aimpoint’s wide 30 mm ring
or QR-mount. If other standard 30 mm rings are used, make sure that the
ring(s) covers a length of minimum 25 mm or 1”.
b. Ensure that the sight is correctly positioned for right or left hand shooting.
See (g 2) and (g. 3).
NOTE: Installing the Rubber cover (10) requires right-handed shooter
conguration (g. 2).
c. When using lens covers, ensure that they are correctly positioned and can
be opened.
NOTE: make sure that you have space between the bottom front part of the
sight and the top of the base/weapon.
d. Finally, make sure that all screws are rmly tightened around the sight.
e. Complete zeroing according to (2.2.1).
1.3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS
See Fig. 1
Fig. 4 Fig. 5
Fig. 1
Comp M3/ML3
Installing the Rubber Cover
(RIGHT-HANDED SHOOTER CONFIGURATION ONLY!)
Right-handed shooter
conguration
Left-handed shooter
conguration
Fig. 2 Fig. 3
1. Sight
2. Battery Cap
3. Battery (DL1/3N or similar)
4. Rotary Switch
5. Cap Adjustment (2 pcs)
6. Rubber Strap (2 pcs)
7. Adjustment screws for elevation/windage (2 pcs)
8. Lens Cover, rear
9. Lens Cover, front
10. Rubber Cover