AIM & THURLBY THANDAR INSTRUMENTS TG2511A | TG2512A | TG5011A | TG5012A Advanced Function/Arbitrary/Pulse Generators - Single or Dual Channel Up to 50MHz sine and square, 14 digits or 1µHz resolution Arbitrary waveforms of up to 128K points at up to 125MS/s True pulse generator with variable delay and variable rise/fall Internal/external modulation, AM, FM, PM, PWM, Sum, FSK, BPSK Programmable via USB, GPIB and LXI compliant LAN interfaces aimtti.com aimtti.co.uk | aimtti.
Features at a glance TG5011A/TG2511A Function/Arbitrary/Pulse generators 0.001mHz to 50MHz or 25MHz range; 14 digits or 1µHz resolution. Standard waveforms include sine, square, ramp, pulse, sin(x)/x, noise, exponential, logarithmic, PRBS. True pulse generator with variable delay and variable rise/fall. Arbitrary waveforms of up to 128K points at up to 125MS/s. Waveform storage and file transfers using USB flash drives. Waveform Manager Plus for Windows editing software included.
Features at a glance TG5012A/TG2512A 2 Channel Function/Arbitrary/Pulse generators Two identical channels - independent or linked with coupled and tracking modes. Selectable coupling of frequency (equal or offset), amplitude/dc offset. Inter-channel phase offset of -360o to +360o with 0.1o resolution. 0.001mHz to 50MHz or 25MHz range; 14 digits or 1µHz resolution. Standard waveforms include sine, square, ramp, pulse, sin(x)/x, noise, exponential, logarithmic, PRBS.
Features in detail Higher Waveform Frequencies The TG501xA out-performs other generators in its price range by offering both sine and square waves up to 50MHz. The lower cost TG251xA operates to 25MHz. Standard, Pulse and Arbitrary Waveforms Independently variable rise and fall The generators offer very fast edge speeds of better than 8ns on the TG501xA or 13ns on the TG251xA, but the edges can be slowed down to simulate slower pulses.
Features in detail USB Flash Drive Interface Storage, Modulations, Sweep & Burst PWM Pulse width modulation is available for the pulse function using any Both instruments incorporate a front mounted USB socket for connection of flash memory disk drives which standard or arbitrary waveform including noise. Pulse width deviation is variable between 0% and 100%. can store up to 1,000 waveforms and 1,000 setups.
Features in detail Noise, Phase Locking, Two Channel Operation Two Channel Operation Gated In Gated mode the waveform runs only when the gate signal is true. The start point of the waveform is settable from -360.0 to +360.0 degrees and a the last cycle is completed after the gate signal goes false. All of the options available for triggering are available for gating. The trigger-in socket can be set as high or low for true.
Features in detail Remote Interfaces, Outputs/Inputs, Wave Edit Full Remote Control All functions of the generators can be controlled from the digital interfaces. Arbitrary waveform data can also be loaded using these interfaces. An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows* and HP-VEE*.
Features in detail High Resolution LCD The 3.6” diagonal panel uses 256 x 112 pixels and provides a large amount of simultaneous information. System connection information is shown on the top line. Below that is a general status screen showing five major parameters. These parameters change depending upon the function being used. Below the status information is the main editing line which shows the parameter currently under control.
TG5011A, TG2511A, TG5012A, TG2512A - Technical Specifications Note that specifications apply to 50MHz models (TG5011A and TG5012A) and that specifications for 25MHz models (TG2511A and TG2512A), where different, are in (dark red). For two channel models (TG5012A and TG2512A) specification apply to each output. STANDARD WAVEFORMS SINE Note that purity specifications above 25MHz apply only to the TG5011A & TG5012A.
Technical Specifications (continued) Gated Waveform will run while the Gate signal is true and stop while false. Carrier Waveforms: Sine, Square, Ramp, PRBS, Arb, Pulse, Noise Max. Carrier Freq.: 10 MHz, subject to carrier waveform Trigger Rep. Rate: 2mHz to 1MHz internal, dc to 1MHz external. Gate Signal Source: Internal from keyboard or trigger generator. External from TRIG IN or remote interface. Start/Stop Phase: -360.0 to +360.0 degrees, 0.1 degree resolution, subject to carrier waveform.
Technical Specifications (continued) GENERAL SPECIFICATIONS Display and Data Entry Display: Type: Data Entry: Stored Settings: Black on white backlit graphics display - pixel format: 256 x 112 Keyboard selection of mode, waveform etc.; value entry direct by numeric keys or by rotary control. Up to 9 complete instrument set-ups may be stored and recalled from non-volatile memory. Up to 1000 set-ups can be stored per USB stick. AC Supply AC Input: 110-240VAC ±10% 50/60Hz; 100-120VAC ±10% 400Hz; 60VA max.
