USER MANUAL v1.
1. 2. Safety instructions and warnings ………….…………….1 Overview 2.1. Inside the box …………………………………………………2 2.2. Specification ………………………………………………2-3 2.3. Product overview ..……………………………………………….4 3. Getting started 3.1. Charging and powering monitor unit ……………………………5 3.2. Powering camera unit ……………………………………………6 4. Operation – General mode 4.1. OSD icons ……………………………………………………………7 4.2. Control keys …………….…………………….………………….8 5. Operation – Menu mode 5.1. Video category ……………………………………………….…..9 5.2.
Please read and follow all instructions and warnings in this user manual before using the product. ◼ ◼ ◼ ◼ ◼ ◼ ◼ ◼ ◼ ◼ ◼ Strangulation Hazard - Keep the adapter cord out of the reach of children. Never place the camera or cord within 3 feet of a crib or playpen. Choking Hazard - This product contains small parts which may cause choking. Not for children under 3 years. Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to the instructions.
2.1. Inside the box Thanks for purchasing aidios M1 wireless monitoring system. It contains below components : Monitor unit x 1 Camera unit x 1 Rechargeable Lithium battery x 1 A/C adapters x 2 Wall mounting screw x 1 Adhesive rubber foot (for camera stand) x 4 User manual x 1 2.2. Specification RF frequency 2400 – 2483.
Monitor unit Display 4.3” color TFT LCD, 480x272 Audio Built-in speaker and microphone Battery 1800mAh rechargeable Lithium-ion polymer Duration (Normal) ~9 hours Duration (VOX on) ~15 hours Operating voltage 5V Camera unit Picture sensor 1/5” Color CMOS, 640x480 Optical lens F2.4, EFL 3.7mm, FOV 70∘ Night vision 8 x 940nm IR LEDs Light sensor Built-in Audio Built-in speaker and microphone Operating voltage 5V Mfg. Model # Spec.
2.3.
3.1. Charging and powering monitor unit Loosen the screw and open battery door. Plug in the battery to the battery socket as shown in pic. 1. Close the battery door and tighten the screw. Plug the power adapter into an electrical outlet. Insert the 3.5mm plug to the power jack as shown in pic. 2. The charging process starts and charge LED indicator emits red light. Press and hold the power button for 1 second to turn on the monitor unit. Power LED indicator emits blue light when monitor unit is turned on.
3.2. Powering camera unit Plug the power adapter into an electrical outlet. Insert the 3.5mm plug to the power jack as shown in pic. 3. Slide the power switch to 'ON' position to turn on the camera unit. Power LED indicator emits blue light when camera unit is turned on. NOTE : Do not injest battery, Chemical Burn Hazard. This product contains a Lithium cell battery. If the battery is swallowed, it can cause severe internal burns in short period and can lead to death.
4.1. OSD icons Camera icons : Standard camera unit Camera unit at zoom mode Camera unit with pan tilt docking installed (*) Temperature reading icon will be displayed only when pan tilt docking is installed.
4.2. Control keys Power button Press and hold : Power on/off Short press : Video off mode (audio only) (*) Pan-tilt mode is only available when pan-tilt docking is installed.
To enter menu mode, press ‘Enter’ key once. To leave menu mode, press ‘Exit’ key once. In menu mode, press arrow keys to navigate and select different options. 5.1.
5.2.
5.2.2. VOX Alike auto mute function, the camera unit starts to detect noise level when VOX is enabled. It turns off both video and audio completely after a 10 seconds of continuous silence. Any noise detected afterwards will trigger both systems back on, and repeat the noise detection. Sensitivity setting is the same as auto mute function mentioned in 5.2.1. Note : When VOX is enabled, auto mute function will be disabled automatically. 5.3.
5.3.1 Add a camera 1. Select an ID number for your new camera and move the cursor to this camera ID number by pressing up/down arrow key. 2. Press left/right arrow key and select 'Pair' option. 3. Press 'Enter' key to perform pairing process. 4. Press and hold the 'Pair' button at the back of camera unit for 1 second. The power LED of camera unit will blink to indicate pairing mode. 5. Pairing process will be started automatically.
5.3.3 Picture in picture (PiP) Picture in picture function allows viewing 2 camera units simultaneously. The video image of primary screen will be displayed at normal size. The video image of secondary screen will be reduced to 1/3 of its original size and displayed at lower right corner of screen. No audio will be transmitted from the camera at secondary screen.
Problem Solution Product does not switch on 1. Check the power adapter is properly connected to the device and wall outlets. 2. Swap the power adapter to check if the problem is caused by a defected adapter. 3. Double check if the monitor unit and camera unit is powered on. (Refer to section 3 of this user manual) Screen shows 'Signal lost ! Establishing connection' It indicates that the monitor unit cannot communicate with the camera unit. '1. Check the current camera number if it is correct.
Connection issues (continued) 3. Place the monitor and camera units closer, if possible. 4. Avoid large metallic objects in close proximity to the monitor or camera unit. 5. Place the monitor or camera unit at least 3 feet from any 2.4GHz device, such as WiFi router, smartphone or microwave oven. 6. Try to delete the pairing at the monitor unit, and re-pair to the camera unit. 7. Try to enable smart channeling and use different band to test connectivity.
Annoying beep alerts There are 2 types of beep alerts, low battery and out of range. System delivers one beep every 10 seconds if the monitor cannot communicate with camera unit. System delivers two beeps every 10 seconds if the battery capacity is low. Both alerts can be enabled or disabled in user menu. Battery and charging issue For first time usage, it is always recommended to charge the battery for at least 8 hours before power on.
We warrant to the original user that the product is free from material and workmanship defects for a period of one (1) year from the date of original purchase. If this monitoring system fails to function properly when used as directed under normal condition within the one year period, we will either repair or replace the product, at our discretion, free of charge.
WARNING : Modifications not authorized by the manufacturer may void users authority to operate this device. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Declaration of Conformity : Hereby aidios Ltd., declares that the aidios M1 and the series is in compliance with essential requirements and other relevant provision of Red Directive 2014/53/EU. The product had designed, tested and manufactured according the European Red Directive 2014/53/EU. Information on waste disposal for Consumers of Electrical & Electronic Equipment.
Appendix : For Monitor : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).
