HD-100 HD HDMI POV Camera Ver. 1.
CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warning Precaution This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
6. Do not place conductive objects (e.g. screw drivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center.
HD-100 FRONT BACK Tripod Mounting Hole I/O: Power, OSD RS-485 AUTO IRIS Lens Connector HDMI OUT POWER LED HDMI LED SVC I/O Connector Cable OSD Controller D + - L RS-485 + RS-485 - 485 U R RS-485 Power In 12VDC 4
FEATURES • Full HD Progressive Scan sensor captures sharp and vivid color under different light conditions. • Advanced digital image processor provides vivid and detailed imaged by utilizing WDR, White Balance, and Noise Reduction. • Motion-compensated temporal noise reduction filter leads to effective noise reduction for motion video without blur. • HDMI seamless video performance. • Black Level Set-up provides the better color transition from digital to analog.
OSD MENU 1 MAIN MENU To move from item to item in the menu, move the joystick to the Up/Down. > > > > > > > * WB AE CONTROL CONTROL DAY / NIGHT IMAGE CONTROL SPECIAL SETUP RESET EXIT Move the Cursor Up/Down to Choose Menu 2 Change the Value To change the value of the selected item, move the joystick to the Left/Right. 3 Shift to the Sub Menu of the Chosen Menu R RIGHT SEL DOWN + 6 - 48 5 D LEFT L UP U To go into sub menu, press SEL key. The menu items with > always have its sub menu.
WB CONTROL AWB WB CONTROL * MODE PUSH BLUE RED RETURN ATW Auto white balance mode will adjust white balance within 3,0000K ~ 8,0000K temperature. ATW Auto trace white mode will adjust white balance within 1,9000K ~ 11,0000K temperature. ONE PUSH One push mode is used if AWB or ATW cannot produce the proper white balance. Place a white paper in front of the camera when using the one push mode to self adapt. INDOOR Indoor mode will adjust white balance to indoor lighting conditions.
AE CONTROL AUTO AE CONTROL MODE * AESHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT FLK CONTROL RETURN AUTO Auto mode will adjust the exposure level automatically. AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX 13 OFF 7 OFF “AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control. SENS UP : OFF, x2 ~ x10 “SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality.
AE CONTROL SHUT FIX AE CONTROL * AE MODE SHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT FLK CONTROL RETURN AUTO SHUT FIX mode provides more detailed shutter speed option. All other controls are tuned for the selected shutter speed. SHUTTER : AUTO, 1/30 ~ 1/10,000 13 OFF 8 OFF Shutter speed can be set. AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX “AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.
AE CONTROL AGC FIX AE CONTROL MODE * AESHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT FLK CONTROL RETURN AUTO AGC FIX mode provides more detailed gain option. All other controls are tuned for the selected gain value. AGC : AUTO, 0dB ~ 27dB, d2X ~ d9X 13 OFF 8 OFF Gain level can be set. AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX “AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control. AE BRIGHT : 0~10 Auto Exposure brightness level can be adjusted.
AE CONTROL IRIS SPEED : 0 ~ 5 AE CONTROL MODE * AESHUTTER IRIS AGC AGC MAX SENS UP AE BRIGHT FLK CONTROL RETURN AUTO 13 OFF 8 OFF Electronic Iris speed can be controlled. (DC Iris lens only) LENS MODE : INDOOR, OUTDOOR, MANUAL Lens setting will be optimized for the selected environment.
DAY & NIGHT Adjust color or B&W setting from this menu. DAY & NIGHT MODE * NIGHT COLOR COLOR BURST RETURN DAY (COLOR) MODE : DAY(COLOR), NIGHT(B&W) Set camera to either color mode or B&W mode. NIGHT COLOR : ON, OFF When “NIGHT COLOR” is turned ON, camera stays on color mode even “NIGHT(B&W)” is selected from the MODE. COLOR BURST : ON, OFF Color burst signal ON or OFF can be set for CVBS signal.
IMAGE CONTROL Camera image control can be adjusted from EFFECT menu. * IMAGE CONTROL LENS SHADING CONTRAST BRIGHTNESS SATURATION HUE EDGE ENHANCE AUTO SATURATE AUTO EDGE BLACK LEVEL GAMMA CORRECT DNR RETURN OFF 11 11 10 0 5 MIDDLE ON 0 DEFAULT LENS SHADING : ON, OFF Optical vignetting issue can be corrected from this menu. BLACK LEVEL : -64 ~ 64 Gamma level can be adjusted. GAMMA CORRECT: DEFAULT, 0.4 ~ 1.0 Gamma level can be adjusted.
IMAGE CONTROL * IMAGE CONTROL LENS SHADING CONTRAST BRIGHTNESS SATURATION HUE EDGE ENHANCE AUTO SATURATE AUTO EDGE BLACK LEVEL GAMMA CORRECT DNR RETURN CONTRAST : 0 ~ 20 OFF 11 11 10 0 5 MIDDLE ON 0 DEFAULT Contrast level can be adjusted. BRIGHTNESS: 0 ~ 20 Brightness level can be adjusted. SATURATION : 0 ~ 20 Saturation level can be adjusted. HUE: 0 ~ 20 Hue level can be adjusted. EDGE ENHANCE : 0 ~ 20 Image sharpness level can be adjusted.
SPECIAL SPECIAL Camera special functions can be adjusted from SPECIAL menu. SPECIAL * DZOOM DEFOG DWDR MOTION DETECT BACKLIGHT BINNING DEFECT PIXEL DISP. FUNCTION FLICKER DETECT PRIVACY RETURN ON OFF OFF OFF OFF OFF ON ON DZOOM : ON, OFF > Digital Zoom and PIP function can be enabled from this menu. ZOOM CONTROL: RATIO, POSITION, RETURN Adjust the digital zoom ratio and position. Use LEFT / RIGHT button to adjust the ratio, then press select.
SPECIAL DEFOG : ON, OFF, AUTO DEFOG SETUP * STRENGTH THRESHOLD AUTO LEVEL RETURN “DEFOG” menu improves foggy image. 0 STRENGTH : 0 ~ 16 Change defog strength. THRESHOLD : 0 ~ 3 Threshold value sets minimum sensitivity value for automatic defog control. Higher value makes defog-on control reluctant. AUTO LEVEL : LOW, MID, HIGH Auto level value sets maximum strength value for automatic defog DWDR Wide Dynamic range can be adjusted from the sub menu.
SPECIAL BACKLIGHT : OFF, BLC, HLM BACKLIGHT - BLC * BLC SIZE/POSITION LEVEL DISPLAY DEFAULT RETURN Camera backlight compensation can be adjusted. ON BLC : OFF, ON BLC enables back light compensation. 128 ON SIZE/POSITION : SIZE, POSITION, RETURN Adjust BLC area window size. LEVEL Backlight level compensation level can be adjusted from this menu. Higher level will compensate more from the selected area. DISPLAY : OFF, ON BLC area display can be turned ON or OFF.
SPECIAL BINNING : OFF, ON DEFECT PIXEL PROGRESS * STATIC SDPC UPDATE SDPC CLEAR RETURN 18 PRESS OK PRESS OK PRESS OK Binning can be turned ON of OFF. DEFECT PIXEL : OFF, ON, ON(FIXED), STATIC Defective Pixel Correction feature can be operated. It is turned ON by default and will run both dynamic and static DPC function.
SPECIAL DISPLAY FUNCTION DISPLAY FUNCTION * FREEZE MIRROR IMAGE EFFECT ROTATION PICTURE STYLE PIC CONTRAST PIC SATURATION PIC EDGE RETURN OFF OFF OFF OFF OFF Adjust image display features from this menu. FREEZE : OFF, ON Image freeze can be turned ON or OFF. MIRROR : OFF, MIRROR, V-FLIP, BOTH(H/V) IMAGE EFFECT : OFF, NEGATIVE, GREY MODE, REDDISH-1 ~ 4, BLUISH-1 ~ 4, GREENISH-1 ~ 4. ROTATION : OFF, ROT_L FULL, ROT_L 1:1, ROT_R Full, ROT_R 1:1 Image can be rotated either left or right side.
PRIVACY Privacy zone can be setup from this menu. PRIVACY MASK * MODE TYPE MASK NO. DISPLAY COLOR POLY SELECT POSITION-X POSITION-Y SIZE-X SIZE-Y DEFAULT RETURN ON SQUARE MASK 1 ON BLACK 2 5 20 11 MODE : ON, OFF Enable “PRIVACY ZONE” ON or OFF. TYPE: SQUARE, POLYGON Select privacy zone shape. MASK NO. : MASK1 ~ MASK8 Select privacy zone mask number. DISPLAY : ON, OFF Turn ON or OFF the selected privacy mask zone.
SETUP Camera setup can be adjusted from this menu. CAM TITLE : OFF, ON SETUP TITLE * CAM COMMUNICATION SYSTEM INFO OUTPUT FORMAT RETURN OFF 1080P30 Camera title can be turned ON or OFF. > > > > > COMMUNICATION VISCA communication control can be adjusted. CAM ID:0 ~ 7 Camera ID can be setup. ID DISPLAY:OFF, ON Camera ID can be displayed. BAUDRATE:2400, 4800, 9600, 19200, 38400 Camera baudrate can be set. SYSTEM INFO Camera information can be found under this menu.
SETUP MODE : FACTORY, USER RESET * MODE RESET SAVE AS USER RETURN Camera will reset to factory default or user saved value. FACTORY > RESET Reset the camera to the selected mode. SAVE AS USER Save the user desired setting from the menu. Mode must be set to User.
SPECIFICATION: HD-100 Image Sensor Sensor Size Effective Pixels Pixel Size Resolution Frame Rate Video Signal Output White Balance Lens Audio Input Audio Sample Rate Color Space Camera Control Operation Temperature Dimension & Weight Power Requirements 1/3 inch Progressive CMOS Diagonal 7.2mm(17:9) Horizontal: 1920, Vertical: 1080 2.75 µm (H) x 2.75 µm (V) 1080p / 1080i : 1920 x 1080 720p : 1280 x 720 1080p : 60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 1080i : 60 / 59.94 / 50 720p : 60 / 59.94 / 50 HDMI 1.
Disposal of Old Appliances 1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately form the municipal waste stream stream in accordance to laws designated by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.