Quick Start Assembly Guide

ManualsBrandsAgri-Fab ManualsSpreader45-0463

Figure 7

STEP 7: (SEE FIGURE 7)

• Attach the hopper to the lower set of holes in the

hopper support tubes using four 1/4” x 1-3/4” hex

bolts (23), 1/4” washers (34), nylon washers (33)

and 1/4” nylock nuts (32). Make only nger tight.

STEP 8: (SEE FIGURE 8)

• Installthegrip(42)ontotheowcontrol

arm.

• Assembletheadjustablestop(44)tothe

owcontrolbracketusingthe1/4”x3/4”

carriage bolt (24), nylon washer (33) and

wing nut (43).

Figure 8

STEP 10: (SEE FIGURE 10)

• Installtheendoftheowcontrolrod(10)with

noholeintotheelongatedholeintheow

plate on the bottom of the hopper. Lock the

rodintheowplatebyrotatingtherod.

STEP 9: (SEE FIGURE 9)

• Attachtheowcontrolbrackettothehitch

tube using two 1/4” x 1-3/4” hex bolts (23),

four 1/4” washers (34) and two 1/4” nylock

nuts (32). Do not tighten completely.

Figure 9

Figure 10

STEP 11: (SEE FIGURE 11)

• Swingtheowcontrolrodaroundandinsert

theendoftherodintotheowcontrolarm.

Secure it with a 1/4” washer (34) and a 3/32”

x 3/4” cotter pin (28).

STEP 12: (SEE FIGURE 12)

• Fasten the hopper braces (8) to the hopper

support tubes using two 1/4” x 1-3/4” hex

bolts (23), 1/4” washers (34), nylon washers

(33) and 1/4” nylock nuts (32). Do not tighten

completely.

• Fasten the loose ends of the hopper braces

to the hitch tube using a 1/4” x 2” hex bolt (22)

and a 1/4” nylock nut (32). Do not tighten

completely.

Figure 11

Figure 12

STEP 13

• Tighten all bolts and nuts except for those

shown in step 9 that fasten the control bracket

to the hitch tube.

STEP 15: (SEE FIGURE 14)

• Slide a spacer (27), a 1/2” washer (35), and a

wheel (2) onto the round end of the axle.

• Slide a 1/2" washer (35) over the axle and

secure the wheel with a 1/8 x 1-1/4" cotter pin

(29), spreading the ends.

STEP 14: (SEE FIGURE 13)

• Slide a spacer (27), a 1/2” washer (35), and

the drive wheel (2) onto the square end of the

axle.

• Slide a 1/2" washer (35) over the axle and

secure the wheel with a 1/8 x 1-1/4" cotter pin

(29), spreading the ends.

SETTING "5"

OFF

STEP 16: (SEE FIGURE 15)

• Settheadjustablestopat"5"andmovethe

control hande back against it.

• Slide the control bracket along the hitch tube

untiltheowplateinthebottomofthehopper

is open half way.

• Tighten the bolts and nuts fastening the control

bracket. Do not deform the control bracket.

• Makesuretheowplatewillopenandcloseall

theway.Readjustifnecessary.

Figure 13

Figure 15

Figure 14

Quick Start Guide

45-0527 Tow Spreader

Read the manual that came with your Tow Spreader for:

• Important safety warnings

• Further explanation of features

• Operatinginstructionsandowcontroladjustments

Problem?

Call 1-800-448-9282