Installation Guide

Quick Start Guide
45-04622 Push Spreader
Read the manual that came with your Push Spreader for:
• Important safety warnings
• Further explanation of features
• Operatinginstructionsandowcontroladjustments
Problem?
Call 1-800-448-9282
Quick Start Guide
45-04622 Push Spreader
Read the manual that came with your Push Spreader for:
• Important safety warnings
• Further explanation of features
• Operatinginstructionsandowcontroladjustments
Problem?
Call 1-800-448-9282
Figure 7
STEP 7: (SEE FIGURE 7)
• Place the hopper on the hopper support tubes,
inserting the spreader shaft up through the square
hole in the bottom of the hopper.
• Slide the hopper bushing (U) onto the spreader
shaft and insert it into the bottom of the hopper.
• Slide the spacer (O) onto the spreader shaft.
• Install the agitator hairpin (J) in the spreader shaft.
STEP 8: (SEE FIGURE 8)
• Attach the hopper to the upper holes in the
hopper support tubes using four 1/4” x 1-3/4”
hex bolts (C), 1/4” washers (N), nylon washers
(L) and 1/4” nylock nuts (K). Tighten.
• Tighten the bolts and nuts assembled in steps
2 and 3.
Figure 8
J
U
O
STEP 10: (SEE FIGURE 10)
• Slide a 5/8” washer (M), a spacer (P), a 5/8”
washer (M) and a wheel (10) onto the end of
the axle without a hole.
• Using a hammer, carefully tap a hub cap (W)
onto the axle.
STEP 9: (SEE FIGURE 9)
• Slide a 5/8” washer (M), a spacer (P), a 5/8”
washer (M) and a wheel (10) onto the end of
the axle with a hole.
• Secure the wheel to the axle with a 3/16” x 2”
cotter pin (G), spreading the ends of the cotter
pin.
• Using a hammer, carefully tap a hub cap (W)
onto the axle.
Figure 9
Figure 10
W
10
M
P
M
G
G
W
10
M
P
M
K
C
N
L
K
STEP 11: (SEE FIGURE 11)
• Attach the handle tubes (2) to the hopper
support tubes using two 1/4” x 1-3/4” hex bolts
(D), and 1/4” nylock nuts (K). Tighten.
STEP 12: (SEE FIGURE 12)
• Attachtheowcontrolbracket(9)tothe
handle tubes using two 1/4” x 2-3/4” hex bolts
(A), four 1/4” washers (N) and two 1/4” nylock
nuts (K). Do not tighten yet.
Figure 11
Figure 12
K
D
2
D
N
N
A
K
9
STEP 14: (SEE FIGURE 14)
• Inserttheupperendoftheowcontrolrod
(5)throughtheholeintheowcontrolarm.
Secure it with a 1/4” washer (N) and a 3/32”
x 3/4” cotter pin (I), spreading the ends of the
cotter pin.
Figure 13
Figure 14
N
I
5
5
5
Z
STEP 13: (SEE FIGURE 13)
• Insertthelowerendoftheowcontrolrod(5)
through the hole in the drive link bracket (Z)
and then twist the rod so that the end points
down.
STEP 16: (SEE FIGURE 16)
• Settheadjustablestopat“5”andmovethe
control arm against it.
• Slide the control bracket along the handle tube
untiltheowplateinthebottomofthehopper
is open half way.
• Tighten the bolts and nuts attaching the control
bracket to the handle tubes. Do not indent the
control bracket when tightening.
• Makesuretheowplateiscompletelyopenat
the highest setting and completely closed at
the“OFF”setting.Re-adjustifnecessary.
STEP 15: (SEE FIGURE 15)
• Installthegrip(Y)ontotheowcontrolarm.
• Install the handle grips (Q) onto the handles.
• Assembletheadjustablestop(S)totheow
control bracket using the 1/4” x 3/4” carriage
bolt (F), nylon washer (L) and wing nut (R).
Figure 16
Figure 15
OFF
1
–
2
–
3
–
4
–
5
–
6
–
7
–
8
–
9
–
1
0
–
"5"
Y
Q
Q
L
R
S
F