Installation Guide

ManualsBrandsAgri-Fab ManualsKitchenSmart Spreader 130 lb. Push Broadcast Spreader

Quick Start Guide

45-04622 Push Spreader

Read the manual that came with your Push Spreader for:

• Important safety warnings

• Further explanation of features

• Operatinginstructionsandowcontroladjustments

Problem?

Call 1-800-448-9282

HARDWARE PACKAGE

FORM NO. 45497 (07/19/17)

x13

43796

49870

1509-69

46699

43012

44950

46855

43093

44101

48934

452802362543088

R19212016

1543-6947189

44482

47141

24858

48499B 49449 43848 27277 41929

28325

45279

44285

42839

Quick Start Guide

45-04622 Push Spreader

Read the manual that came with your Push Spreader for:

• Important safety warnings

• Further explanation of features

• Operatinginstructionsandowcontroladjustments

Problem?

Call 1-800-448-9282

STEP 1: (SEE FIGURE 1)

• Insert the plugs (X) into the end of the hopper

support tubes (8).

• Press the hex bushings (T) into the hex holes

in the bottom of the hopper support tubes (8).

• Slide the hopper support tubes (8) onto the

gearbox axle.

STEP 2: (SEE FIGURE 2)

• Install the stand tube (7) between the hopper

support tubes as shown, using two 1/4” x 2”

hex bolts (C), spacers (BB), and 1/4” nylock

nuts (K). Place the spacers between the

hopper support tubes and the stand tube. Do

not tighten completely.

Figure 2

Figure 3

STEP 3: (SEE FIGURE 3)

• Insert the bushing (V) into the cross brace (4).

• Slide the cross brace (4) onto the vertical

gearbox shaft and attach the cross brace to

the hopper support tubes (8) using two 1/4” x

2-1/2” hex bolts (B) and 1/4” nylock nuts (K).

Do not tighten completely.

Figure 4

STEP 5: (SEE FIGURE 5)

• Installtheattenedendofthedrivelinkrod

(AA)intotheholeintheowplate.Twistthe

rodtolockitintheowplate.

STEP 6: (SEE FIGURE 6)

• Install the drive link bracket (Z) onto the end of

the drive link rod (AA).

• Attach the drive link bracket (Z) to the bracket

already attached to the bottom of the hopper

using a 1/4” x 3/4” hex bolt (E) and a 1/4”

nylock nut (K). Tighten the nut and then back

it off 1/4 to 1/2 turn.

Figure 5

Figure 6

TOOLS REQUIRED FOR ASSEMBLY

(1) Hammer

(1) Pliers

(2) 7/16" Wrenches

Figure 1

STEP 4: (SEE FIGURE 4)

• Slide the spreader impeller (3) onto the

spreader shaft and secure it with a 1/8” x

1-1/2” cotter pin (H) by spreading the ends of

the cotter pin.

Summary of content (2 pages)

PAGE 1
Quick Start Guide Read the manual that came with your Push Spreader for: • Important safety warnings • Further explanation of features • Operating instructions and flow control adjustments 45-04622 Push Spreader B x2 C x6 D x2 E x1 43012 G x1 F x1 44950 R19212016 N x9 K x13 43088 1543-69 R x1 Q x2 47141 49449 43848 4 8 B X 8 K 45280 V x1 U x1 44285 Z x1 27277 AA 8 B P x2 T Figure 5 Figure 3 42839 T AA x1 BB x2 44482 48499B STEP 5: (SEE FIGURE 5) • Install the flattened end of
PAGE 2
Quick Start Guide Read the manual that came with your Push Spreader for: • Important safety warnings • Further explanation of features • Operating instructions and flow control adjustments 45-04622 Push Spreader STEP 7: (SEE FIGURE 7) • Place the hopper on the hopper support tubes, inserting the spreader shaft up through the square hole in the bottom of the hopper. • Slide the hopper bushing (U) onto the spreader shaft and insert it into the bottom of the hopper.