™ OWNERS MANUAL Model No. 45-03641 250 LB. ATV BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully • • • • • Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com PRINTED IN USA FORM NO. 49857 (REV.
RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • • • • • Read the towing vehicle owners manual and towing vehicle safety rules. Know how to operate your tractor before using the broadcast spreader attachment. Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading.
SHOWN FULL SIZE I G A B C D F E H J L M K N O P NOT SHOWN FULL SIZE Q KEY A B C D E F G H I J K L R U T S QTY. DESCRIPTION 4 5 1 2 2 1 8 4 2 4 7 4 Hex Bolt, 5/16" x 1-3/4" Hex Bolt, 1/4" x 1-3/4" Hex Bolt, 1/4" x 2" Hex Bolt, 3/8" x 3/4" Hex Bolt, 1/4" x 1" Carriage Bolt, 1/4" x 3/4" Nylock Hex Nut, 1/4" Nylock Hex Nut, 5/16" Nylock Hex Nut, 3/8" Nylon Washer Flat Washer, 5/16" Flat Washers, 3/4" 3 KEY QTY.
ASSEMBLY INSTRUCTIONS 6. Assemble the four outer hitch braces to the hitch tube using a 1/4" x 2" hex bolt (C) and a 1/4" nylock hex nut (G). DO NOT TIGHTEN YET. Do not assemble the two inner hitch braces at this time. See figure 2. TOOLS REQUIRED FOR ASSEMBLY (1) (2) (2) (2) Pliers 7/16" Wrenches 1/2" Wrenches 9/16" Wrenches STACK HITCH BRACES AS SHOWN (C) 1/4" x 2" HEX BOLT REMOVAL OF PARTS FROM CARTON HITCH TUBE Remove all parts and hardware packages from the carton.
15. Assemble the two inner hitch braces to the flow control mounting tube using a 1/4" x 1-3/4" hex bolt (B) and a 1/4" nylock hex nut (G). DO NOT TIGHTEN YET. See figure 6. 16. Tighten all nuts and bolts assembled up to this point. Do not collapse the tubes when tightening. 9. Assemble a spacer (Q), a 3/4" flat washer (L), a wheel (air valve facing out) and another 3/4" flat washer (L) onto the end of the axle that has both the large and small holes. See figure 4. 10.
18. Assemble the vinyl grip (U) onto the flow control arm. See figure 8. 19. Insert the flow control arm down through the slot in the flow control bracket. Assemble the small hole of the flow control link (V) to the flow control arm using a 1/4" x 1" hex bolt (E), a nylon washer (J) and a 1/4" nylock hex nut (G) as shown in figure 8. Tighten carefully. The flow control link should be snug but should pivot with no more than slight resistance. 21.
(R) NYLON WING NUT 25. Place the screen down into the hopper, sliding the edge of the screen under one of the clips. Slightly bow the screen to slide the opposite side of the screen under the other clip. See figure 14. OF F (K) 5/16" FLAT WASHER ON (J) NYLON WASHER 10 9 8 7 6 5 4 3 2 CLIP 1 SCREEN (S) ADJUSTABLE STOP (F) 1/4" x 3/4" CARRIAGE BOLT FIGURE 12 24. Position the flow control mounting bracket (figure 13). a. Push on flow control arm until it locks in "OFF" position. b.
THE FREE WHEELING FEATURE (Refer to figure 4 on page 5.) 28. For most vehicles, assemble the hitch extension bracket to the holes in the hitch tube shown at the top of figure 16. Use two 1/4" x 1-3/4" hex bolts (B) and 1/4" nylock hex nuts (G) tightened only finger tight. Attach the spreader hitch to your vehicle hitch. Check for interference with the spreader directly behind and out to both sides of the vehicle.
CHECK TIRE INFLATION 3. Check if tires are adequately inflated before each use. Do not inflate beyond maximum recommended pressure. REFER TO CHARTS CAUTION: DO NOT inflate tires beyond the maximum recommended pressure printed on side of tire. CLEANING 4. Rinse inside of hopper and exterior of spreader and dry off before storing. OVERLAP LUBRICATE (See figure 18) 5. Lightly apply automotive grease as needed to the sprocket and gear. 6.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-03641 47 42 34 45 54 54 9 8 39 ON 1 2 3 4 64 5 6 7 8 39 9 10 54 38 B 13 61 40 39 35 51 54 39 41 11 2 60 63 B 37 30 40 A 4 39 31 58 3 59 26 27 4 12 9 10 D 9 57 40 6 46 35 9 25 23 C 32 7 52 50 49 15 33 E 36 29 62 9 7 28 65 9 5 29 40 24 50 A 55 13 19 E 24 7 13 23 21 18 43 20 21 22 19 9 14 17 D 15 49 11 65 35 1 54 9 9 9 58 F OF 53 58 44 65 35 50 50 16 48 C 37 10 56
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-03641 REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 PART NO. QTY. 49414 1 43882 4 65129 1 44462 1 23753 1 23758 1 HA21362 5 24857 1 47189 18 43808 1 43084 4 44180 2 47810 6 48864 1 48511 2 25080 1 23014 1 24914 1 43851 2 43871 1 1540-32 5 1540-162 1 47615 2 47683 2 25305 1 04367 1 43850 1 44468 1 44285 2 25672 2 48934 1 43070 5 43054 2 48586 1 DESCRIPTION REF. NO. PART NO. QTY.
the fastest way to purchase parts www.speedepart.com © 2005 Agri-Fab, Inc. REPAIR PARTS Agri-Fab, Inc. 809 South Hamilton Sullivan, IL. 61951 217-728-8388 www.agri-fab.
