™ owners manual Model No. 45-0364 250 LB. ATV BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully • • • • • Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com PRINTED IN USA FORM NO.
RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • • • • • Read the towing vehicle owners manual and towing vehicle safety rules. Know how to operate your tractor before using the broadcast spreader attachment. Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading.
SHOWN FULL SIZE H F A B C E D G I K L J M N O NOT SHOWN FULL SIZE P KEY A B C D E F G H I J K QTY. 4 5 2 2 1 7 4 2 4 7 4 Q T S R DESCRIPTION Hex Bolt, 5/16" x 1-3/4" Hex Bolt, 1/4" x 1-3/4" Hex Bolt, 3/8" x 3/4" Hex Bolt, 1/4" x 1" Carriage Bolt, 1/4" x 3/4" Hex Lock Nut, 1/4" Hex Lock Nut, 5/16" Hex Lock Nut, 3/8" Nylon Washer Flat Washer, 5/16" Flat Washers, 3/4" KEY QTY.
ASSEMBLY INSTRUCTIONS STACK HITCH BRACES IN PAIRS TOOLS REQUIRED FOR ASSEMBLY (1) (2) (2) (2) Pliers 7/16" Wrenches 1/2" Wrenches 9/16" Wrenches SHAFT SUPPORT PLATE CROSSOVER TUBE MIDDLE BOLT REMOVAL OF PARTS FROM CARTON HITCH TUBE Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on pages 2 and 3. 1. Turn the spreader upside down as shown in figure 1.
9. Assemble a spacer (P), a 3/4" flat washer (K), a wheel (air valve facing out) and another 3/4" flat washer (K) onto the end of the axle that has both the large and small holes. See figure 4. 10. Install a 1/8" x 1-1/2" cotter pin (M) into the small hole in the end of the axle. See figure 4. 11. Open the bail on the drive pin (V) and install it through the wheel and the large hole in the axle. Close the bail to lock the pin in place. See figure 4. 15.
18. Assemble the vinyl grip (T) onto the flow control arm. See figure 7. 19. Insert the flow control arm down through the slot in the flow control bracket. Assemble the small hole of the flow control link (U) to the flow control arm using a 1/4" x 1" hex bolt (D), a nylon washer (I) and a 1/4" hex lock nut (F) as shown in figure 7. Tighten carefully. The flow control link should be snug but should pivot with no more than slight resistance. 21.
(Q) NYLON WING NUT 25. Assemble the hitch bracket to the hitch extension bracket using two 3/8" x 3/4" hex bolts (C) and 3/8" hex lock nuts (H). Insert the bolts from the bottom. See figure 13. 26. Assemble the hitch pin (O) through the hitch bracket and the hitch extension bracket and secure with the hair cotter pin (N). See figure 13.
OPERATION 10. To insure uniform coverage, make each pass so that the broadcast pattern slightly overlaps the pattern from the previous pass as shown in figure 15. The approximate broadcast widths for different materials are shown in the application chart on this page. 11. When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs. 12. Heavy moisture conditions may require a cover over the hopper to keep contents dry.
MAINTENANCE STORAGE CHECK FOR LOOSE FASTENERS 1. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. 1. Rinse inside of hopper and exterior of spreader and dry off before storing. 2. Store in a clean, dry area. CHECK FOR WORN OF DAMAGED PARTS 2. Check for worn or damaged parts before each use. Repair or replace parts if necessary. CHECK TIRE INFLATION 3. Check if tires are adequately inflated before each use.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-0364 47 44 42 34 45 54 54 8 39 ON 1 2 3 4 5 6 7 8 39 9 10 66 64 B C 63 40 11 60 C 37 40 A B 39 4 31 40 58 3 59 26 4 12 9 10 E 62 9 9 40 57 6 46 7 28 67 9 5 29 27 51 54 39 41 2 1 49 15 35 33 9 25 23 24 55 13 7 13 23 21 18 43 20 19 21 22 9 14 17 E 15 67 35 49 16 48 D 50 50 50 50 A D 32 7 52 F 36 29 24 19 F 11 54 61 39 54 9 9 58 58 F OF 65 13 9 67 10 56
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-0364 REF. PART NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 32 33 34 QTY.
the fastest way to purchase parts www.speedepart.com © 2005 Agri-Fab, Inc. REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.
