Agri-Fab ® OWNERS MANUAL Model No. 45-0355 3 PT. HITCH TANG CULTIVATOR CAUTION Read Rules for Safe Operation and Instructions Carefully • • • • • Safety Assembly Operation Maintenance Parts SpeedEPart the fastest PRINTED IN USA way to purchase parts www.speedepart.com FORM NO. 48973 (REV.
SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand operate the equipment. Exercise caution at all times when using power equipment. CAUTION: IMPORTANT SAFETY PRECAUTIONS. IT MEANS - ATTENTION! BECOME ALERT! LOOK FOR THIS SYMBOL TO POINT OUT YOUR SAFETY IS INVOLVED. ,_ 1. 2. 3. 4. 5. 6. Read this owner's manual before using this equipment. Do not allow children to operate the tow vehicle or the tine cultivator.
H I 1 \ B A / \ K L / J N \ \ PARTS PACKAGE KEY QTY. A B C D E F G 2 1 1 2 2 2 1 CONTENTS - PARTS SHOWN ACTUAL DESCRIPTION Category Pivot Pin Haircotter Hex Bolt, Hex Bolt, Hex Bolt, Hex Bolt, 1 Pin Pin, 1/8" 3/8" x 2-1/4" 1/2" x 1-1/2" 1/2" x 2-3/4" 1/2" x 3-1/2" Lg. Lg. Lg. Lg. J SIZE KEY QTY. H I J K L M N 2 26 11 5 1 2 2 DESCRIPTION Hex Bolt, 3/8" x 1" Lg.
ASSEMBLY TOOLS (2) (2) (2) (1) Turn the frame assembly upright. Attach two depth gauge bars to the frame using a 3/8" U-bolt and two 3/8" Nylock hex nuts for each bar. Put each depth gauge bar next to each outside tang on the rear of the frame as shown in figure 2. Use the holes in each bar that will give the desired working depth, if known at this time. Use matching holes in both depth gauge bars to keep the cultivator level.
4. Attach the cross brace and the two mast sides to 6. the ends of the mast extension straps. The cross brace is between the extension straps while the mast sides are on the outside. The cross brace and mast sides are connected to the extension straps using two category 1 pins, two 7/8" lock washers, and two 7/8" hex nuts. Do not tighten yet. See figure 4. Install the pivot pin through the upper hole at the end of the mast sides. Secure the pivot pin with a 1/8" hair cotter pin. See figure 6.
, 9. Attach the front of the weight bracket to the support bracket using two 3/8" x 1" hex bolts and two 3/8" Nylock hex nuts. Attach the sides of the weight bracket to the rear of the frame using two 3/8" x 2-1/4" hex bolts and two 3/8" Nylock hex nuts. See figure 8. Tighten To adjust the depth gauge bars, remove the nuts from the U-bolt securing each bar to the frame. Then reposition the U-bolt in another set of holes for the desired depth of cultivation.
REPAIR PARTS FOR MODEL NO. 45-0355 3 PT. HITCH TANG CULTIVATOR 17 23 v 2 23 REF. NO. PART NO. QTY. 1 2 3 4 5 6 7 8 9 10 11 12 48982 48970 25154 25167 25180 43343 712-3083 25158 48979 25169 46526 48978 2 2 1 1 2 1 5 2 2 2 1 1 DESCRIPTION Lock Washer, 7/8" Hex Nut, 7/8" Cross Brace Spacer, Mast Lift Strap Mast Lift Strap Haircotter Pin, 1/8" x 2-3/8" Hex Nut, Nylock, 1/2" Mast Side Category 1 Pin Mast Extension Strap Hex Bolt, 1/2" x 3-1/2" Pivot Pin, 3-3/4" Lg. Lg. REF. NO. PART NO. QTY.
SpeedEPart_ _ _ to._._e_ REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com www.speedepart.
