Owner`s manual

IMPORTANT:Do not overtightenboltsfasteningto
tank.Tightenuntillockwashersaresnugandflattened.
11.Attachthetanktotheframeusingsix1/2"spacers
withsix 3/8"x 1-1/4"hex bolts,3/8" lockwashers
and3/8"flat washers.Placethespacersbetween
thetankandtheframe.Tighten thesix boltsuntil
the lockwashersareflattened.Seefigure8.
12.Assemblethe hosehooksto the front of the tank
using two #10-24x 1/2" screws,two 3/16" lock
washersand two flanged spacers.Tighten the
screwsuntil the lock washersare flattened.See
figure8.
I
!
3/16" LOCK /
FLANGED WASHER
FIGURE 8
3/8" FLAT
WASHER
3/8" LOCK
WASHER 3/8" x 1-1/4"
HEX BOLT
13. Tighten securely the 12 bolts and nuts fastening
the frame strap and the front and rear angles to
the side angles. (Figures 1 and 2)
Tighten only until snug the 2 bolts and nuts fas-
tening the axle to the frame. (Figure 4)
Tighten securely the 4 nuts fastening the tongue
to the frame. (Figure 3)
14. Assemble the (RH) and (LH) boom mount assem-
blies to the boom mount brackets using two 5/16"
x 3/4" hex bolts, 5/16" lock washers and 5/16" hex
nuts. Fasten through the slotted hole in each
boom mount assembly. Do not tighten yet. See
figure 9.
15. Align the holes in the boom transport bracket with
the holes in the ends of the boom mount assem-
blies as shown in figure 9. Fasten them together
using two 5/16" x 1" hex bolts, 5/16" lock washers
and 5/16" hex nuts. Tighten the bolts assembled
in this step and in step 14.
NOTE: If the holes in the boom mount assemblies
won't line up, temporarily loosen the bolts which
fasten the boom mount brackets to the frame.
s _.....
5116" x 314" 5116" x 1"
i J HEX BOLT HEX BOLT
i i
rf i /
(LH) BOOM / 5/16"
MOUNT LOCK
ASSEMBLY WASHERS
%
4\\\
"BOOM
/TRANSPORT
/ BRACKET
FIGURE 9
.5/16 (RH) BOOM
F -
........ HEX MOUNT
.... NUTS ASSEMBLY
VIEWED FROM REAR
16. Assemble a 3/8" x 3/4" hex bolt, 3/8" lock washer
and 3/8" hex nut to the hole shown in the bottom
of the welded bracket on the (RH) boom arm
assembly. Tighten. See figure 10.
17. Assemble a spring and a 3/8" hex nut onto a 3/8"
x 1-1/4" hex bolt. Fasten the bolt to the hole shown
in the top of the welded bracket using a 3/8" lock
washer and 3/8" hex nut. Tighten, leaving the
spring free to rotate. See figure 10.
18. Repeat steps 16 and 17 for the (LH) boom arm
assembly.
(RH) BOOM
MOUNT ASSEMBLY
318" x 314" HEX BOLT
7_------ 318"x 1-1/4" HEX BOLT
SPRING
_3/8" REX NUT
(RH) BOOM
ARM ASSEMBLY
LOCK WASHER
3/8" HEX NUT
FIGURE 10
(RH) SIDE VIEWED FROM REAR