ORIGINAL INSTRUCTIONS For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Warning: Only tools equipped with over load protection, when motor has been cut off due to over load, always switch on machine with no load for at least 3 minutes to reduce temperature before switch on again to avoid burn out to the motor.
Power input 2200W Voltage See machine nameplate Speed 1 400-850 No load min-1 Speed 2 750-1640 Speed 3 1550-3450 On rig 8in (200mm) Max. core bit By hand 6in (160mm) Available arbor thread Male: 1-1/4" - 7 UNC or Female: 1/2 BSP Neck diameter 60mm Dimensions 552mm x 110mm x 150mm Soft start & Overload protection with Net weight 6.0 kg ( 13.
GENERAL SAFETY INSTRUCTIONS refrigerators. There is an increased risk of electric shock if your body is earthed or WARNING! Read all safety warnings grounded. and all instructions. Failure to follow c) Do not expose power tools to rain or wet the warnings and instructions may result in conditions. electric shock, fire and/or serious injury. Water entering a power tool will increase Save all warnings and instructions for future the risk of electric shock. reference.
personal injuries. c) Disconnect the plug from the power c) Prevent unintentional starting. Ensure the source and/or the battery pack from the switch is in the off-position before power tool before making any adjustments, connecting to power source and/or battery changing accessories, or storing power pack, picking up or carrying the tool. tools.
Symbols used in this manual carry important information. If V…….....volts unreadable or missing, obtain a A…….....amperes replacement . 6. Hz……....hertz WARNING! Some dust created by W…….....watt power sanding, sawing, grinding, ~………...alternating current drilling, and other construction n0……….no load speed activities contains chemicals known to min ……..revolutions or reciprocation cause cancer, birth defects or other -1 per minute reproductive harm. Some examples of ……….
a way that allows you to avoid injury if ELECTRICAL CONNECTION the bit gets stuck. This machine is equipped with a safety clutch to WARNING! To reduce the risk of injury, protect the always use a Ground. Fault Circuit machine and operator but caution should always be used. Interrupter (GFCI) or a Portable Residual 11. W h e n t h e e l e c t r o n i c o v e r l o a d Current Device (PRCD) device with protection kicks in.
terminal. Your tool must be plugged into an Total Extension appropriate outlet, properly installed and Cord Length (feet) Cord Size (AWG) 25 50 100 150 200 grounded in accordance with all codes and ordinances. Intended use This drilling machine is designed exclusively 16 12 10 8 6 for the drilling of masonry, concrete, steel reinforced concrete and similar types of UNPACKING materials.
shank pilot drill into the taper in the release connector. Keep the water extension arbor. control valve closed until drilling begins. NOTE: the pilot drill must be suitable for 4. masonry and be long enough to stand Attach a GFCI or PRCD device (not included) inline with the power source proud of the core bit. and plug in the power supply cord. Spindle 5. Put on all eye and hearing protection before beginning drilling.
screw by crank handle before Variable speed thumbwheel proceeding. Hexagonal Screw Head ● THE OPTIONAL RIG Crank Handle An optional rig stand is available to allow stable drilling with larger bits up to 8” (200mm). Hexagonal Screw Head ● OPTIONAL RIG-ASSEMBLY 1. To attach the motor to the rig, first remove the core bit . 2. Remove the side handle and clamp. 3. Fully loosen the clamping bolt on the Cradle Clamp Bracket to open the 7. clamp.
● OPERATION - DRY DRILLING, Hand-held from wandering until the bit is fully 1. With the pilot bit not yet in contact penetrated into the cut. Hold firmly to with the workpiece, hold the machine keep the bit straight. If it is impossible tightly 2. to resist the substantial start up to hold the bit still enough to begin the torque and turn the motor on by cut, perhaps the concrete is too hard squeezing the trigger switch. . for the bit size and/or rpm.
7. well. ● RESHARPENING A GLAZED BIT When the cut is finished keep the If you find the bit to be glazed, first reduce motor running until the bit is removed the water flow until the water exiting the from the cut to avoid it getting stuck. cut is really muddy.
Wear safety glasses while using compressed air. ● THE CARBON BRUSHES Carbon brushes are a consumable part CAUTION: When drilling in a position with and must be replaced when a specified the motor near to the floor, take measures wear limit has been reached. These are full to prevent debris and slurry from being stop brushes, so if they are worn to their sucked into the motor's cooling slots limit, the motor will not be able to run. Both brushes should be replaced at the same MAINTENANCE time.
SPEED CONTROL UNIT 2 BLACK 1 RED 2 WHITE 1 BLACK BLACK SWITCH MOTOR GEAR PLATE BRUSH CARBON BRUSH CARBON EARTH AC WIRING
13 14 14 17 13 15 16 14 15 16 07 17 01 08 02 23 84 OPTIONAL 05 A1 24 03 07 10 11 NO.01~94 A1~A2 V2.
PARTS LIST NO. Parts Name Q'TY NO. Parts Name Q'TY 1 POWER SUPPLY CORD 1 51 GEAR CASE 1 2 CORD ARMOR 1 52 SELECTOR DISC SET 1 3 SCREW M4 x 16 2 53 N/A - 4 CORD CLIP 1 54 O-RING φ3 x φ20 x φ26 1 5 SWITCH LOCK-ON 1 55 SPRING φ0.5 x φ4 x φ5 x 5L x 4T 1 6 SCREW M4 x 20 5 56 CHECK BALL φ5 1 7 SCREW M5 x 30 4 57 GEAR SELECTOR 1 8 D-HANDLE HALF-RIGHT 1 58 O-RING φ3 x 1.
24 23 22 21 20 03 02 01 16 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 04 05 09 17 06 20 09 07 16 10 08 19 18 15 14 13 44 43 11 12 50 45A 49 48 47 46 20 21 29 45B 34 A3 A1 OPTIONAL 35 33 47 31 32 30 A2 20 01 38 37 27 45C 28 25 42 26 40 41 40 36 25 20 21 39 35 34 RIG
RIG PARTS LIST ( Optional ) Parts Name No. Q'TY (nECK dIA.) 43mm 68mm 60mm 1 SCREW M5 x 10 4 4 4 2 COLUMN CAP PLATE 1 1 1 3 COLUMN 1 1 1 4 MITER SCALE 1 1 1 5 LOCK PLATE 30 x 39.5 x 10 x M8 1 1 1 6 BUTTRESS LOCK 1 1 1 7 FLAT WASHER Ø5/16" x Ø17 x 1.5 1 1 1 8 ANGLE LOCK CLAMP 1 1 1 9 NUT-NYLOCK 3 3 3 10 BUTRESS BAR 2 2 2 11 HANDLE 1 1 1 12 SCREW M8 x 85 1 1 1 13 SCREW M12 x P1.
No. Parts Name Q'TY (nECK dIA.
