SIDEWINDER THERMAL IMAGING MONOCULAR
Thermal Image Scope User Manual Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Thermal Image Scope User Manual LATTER PREVAILS.
Thermal Image Scope User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Thermal Image Scope User Manual Directive 2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
Thermal Image Scope User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Thermal Image Scope User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Laws and Regulations ● Use of the product must be in strict compliance with the local electrical safety regulations. Transportation ● Keep the device in original or similar packaging while transporting it. ● Keep all wrappers after unpacking them for future use.
Thermal Image Scope User Manual We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. ● Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary. ● If the equipment is used in a manner not specified by the manufacturer, the protection provided by the device may be impaired. ● It is recommended to reboot the device every 2 hours when using it to ensure the device performance.
Thermal Image Scope User Manual Table of Contents Chapter 1 Overview.................................................................................................................... 1 1.1 Device Description................................................................................................................. 1 1.2 Main Function ........................................................................................................................ 1 1.3 Appearance ..............................
Thermal Image Scope User Manual Chapter 8 Client Software Connection ...................................................................................... 17 Chapter 9 CVBS Output ............................................................................................................ 18 Chapter 10 Language Settings ................................................................................................... 19 Chapter 11 Unit Settings ..............................................................
Thermal Image Scope User Manual Chapter 1 Overview 1.1 Device Description The thermal telescope is equipped with high-sensitivity IR detector, and adopts advanced thermal imaging technology, to get clear view in poor visibility or dark environment. It helps to view the target and measure the distance. It can view the moving target and meet the outdoor condition. The device can be widely used for searching and rescuing, hunting, etc. 1.
Thermal Image Scope User Manual Figure 1-1 Buttons and Interfaces Table 1-1 Button and Interface Description No. Component Function 1 Lens Cover Protect the lens. 2 Focus Ring Adjust the focal length. 3 Power Key 4 Capture Key 5 Menu Key 6 Zoom Key Press to switch digital zoom. 7 Diopter Adjustment Ring Adjust the dioptric correction. 8 Eyepiece View the target. 9 Battery Compartment Install battery in it. 10 Data Exchange Interface Charge the device and transmit data.
Thermal Image Scope User Manual Chapter 2 Preparation 2.1 Cable Connection Connect the device and power adaptor with a type-C cable to power on the device. Alternatively, connect the device and PC to export files. Figure 2-1 Cable Connection 2.2 Install Battery Insert the battery into the battery compartment. Steps 1. Unlock the battery compartment cover. Figure 2-2 Unlock Battery Compartment Cover 2. Open the battery compartment cover.
Thermal Image Scope User Manual Figure 2-3 Open Battery Compartment Cover 3. Insert the battery into the battery compartment as the positive and negative marks indicate. Figure 2-4 Install Battery 4. Close the battery compartment cover and lock it. Figure 2-5 Complete Installation Take the battery away if the device is not used for a long time. 2.
Thermal Image Scope User Manual Set the auto power off time for your device, and then the device will automatically shut down as the set time. Steps 1. Hold to go to the menu. 2. Rotate the wheel to select , and press to select the auto power off time as required. 3. Hold to save and exit. Note ● See the battery icon for the battery status. means the battery is fully charged, and means that the battery is low. ● When the low power note shows, charge the battery.
Thermal Image Scope User Manual Chapter 3 Image Settings 3.1 Adjust Diopter Steps 1. Power on the device. 2. Hold the device and make sure the eyepiece covers your eye. 3. Adjust the diopter adjustment ring until the OSD text or image is clear. Figure 3-1 Adjust Focus Ring Note When adjusting diopter, DO NOT touch the surface of lens to avoid smearing the lens. 3.2 Adjust Focus Steps 1. Power on the device. 2. Open the lens cover. 3. Hold the device and make sure the eyepiece covers your eye. 4.
Thermal Image Scope User Manual Figure 3-2 Adjust Focus Note When adjusting focus, DO NOT touch the surface of lens to avoid smearing the lens. 3.3 Adjust Brightness In the menu mode, select and press to adjust brightness. In white hot mode, the higher the value of brightness is, the brighter the image is. The image effect in white hot mode is showed as picture below and effect in black hot mode is opposite. Figure 3-3 Adjust Brightness in White Hot Mode 3.
Thermal Image Scope User Manual 3.6 Set Palettes You can select different palettes to display the same scene in different effects. In the live view interface, press to switch palettes. White Hot The hot part is light-colored in view. The higher the temperature is, the lighter the color is. Black Hot The hot part is black-colored in view. The higher the temperature is, the darker the color is. Red Hot The hot part is red-colored in view. The higher the temperature is, the redder the color is.
Thermal Image Scope User Manual Fusion From high temperature to low temperature, the image is colored in from white, yellow, red, pink to purple. 3.7 Correct Defective Pixel The device can correct the defective pixels on the screen which are not performed as expected. Steps 1. Hold to show the menu. 2. Select . 3. Press to select the axis direction. If you select X, the cursor moves left and right; if you select Y, the cursor moves up and down. 4. Press or to move the cursor to the defective pixel. 5.
Thermal Image Scope User Manual Note ● The selected defective pixel can be magnified and displayed at the bottom right of the interface. Figure 3-5 Correct Defective Pixel ● If the screen OSD blocks the dead pixel, the device performs mirror display automatically. Figure 3-6 Mirror Effect 3.8 Image Pro Image pro refers to image detail enhancement. When you enable this function, the details of the image that is in the image pro frame will be enhanced. Steps 1. Hold 2. Select 3. Press 4.
Thermal Image Scope User Manual 3.9 Flat Field Correction This function can correct non-uniformity of display. Steps 1. Hold to go to the menu. 2. Select and press to switch FFC mode. – Manual: Hold in live view to correct the non-uniformity of display. – Auto: The device performs FFC automatically according to the set schedule when switching on the camera. – External: Cover the lens cover, then hold in live view to correct the non-uniformity of display. 3. Hold to save the settings and exit. 3.
Thermal Image Scope User Manual Chapter 4 Burning Prevention This function can prevent the detector of the thermal channel from being burned. When you enable this function, the shield will close if the grey scale of the detector reaches a certain value. Steps 1. Hold 2. Select 3. Hold to show the menu. and press to enable or disable the burn-prevention function. to save settings and exit. Note When the burn-prevention function is disabled, the shield should be opened if it closes.
Thermal Image Scope User Manual Chapter 5 Hot Tracking The device can detect the highest temperature spot in the scene and mark it on display. Steps 1. Hold 2. Select 3. Hold to show the menu. and press to mark the spot of highest temperature. to save settings and exit. Result When the function is enabled, changes, the moves. displays in the spot of highest temperature.
Thermal Image Scope User Manual Chapter 6 Measure Distance The device can detect the distance between the target and the observation position. Before You Start When measuring the distance, keep the hand and the position steady. Otherwise, the accuracy may be affected. Steps 1. Hold to show the menu. 2. Select and press to go to the setting interface. 1) Press to select the target from Deer, Grey Wolf, Brown Bear, and Custom. 2) Press to select height, and press and to set the target height.
Thermal Image Scope User Manual Chapter 7 Picture and Video You can manually record video or capture picture when displaying live view. 7.1 Capture Picture On the main live view page, press to capture picture. Note When capturing succeeds, the image freezes for 1 second and a prompt shows on the display. For exporting captured pictures, refer to Export Files. 7.2 Set Audio If you enable the audio function, the sound will be recorded with the video.
Thermal Image Scope User Manual The left top of image displays the information of recording time. 2. Hold again to stop recording. What to do next For exporting recording files, refer to Export Files. 7.4 Export Files This function is used to export recorded videos and captured pictures. Before You Start ● Turn off hotspot function. ● Turn on the device after connecting it to your PC, and keep the device on for 10 to 15 seconds before other operations.
Thermal Image Scope User Manual Chapter 8 Client Software Connection Connect the device to the T-Vision App via hotspot, then you can capture picture, record video, or configure parameters on your phone. Steps 1. Hold to show the menu of device. 2. Press to enable hotspot function. 3. Turn on the WLAN of your phone and connect to the hotspot. ● Hotspot Name: Wlan-IPTS Serial No. ● Hotspot Password: the last 9 digits of serial No. 4.
Thermal Image Scope User Manual Chapter 9 CVBS Output The CVBS output is used to debug the device. You can also view the device image on the display unit for details. Before You Start Connect the device to the display unit via CVBS interface of the aviation plug. Steps 1. Hold 2. Select to show the menu. , and press to switch on CVBS. Note The CVBS cable is not included in the package, please purchase it by yourself.
Thermal Image Scope User Manual Chapter 10 Language Settings You can select the device language in this function. Steps 1. Hold 2. Select 3. Press to show the menu. , and press to enter the language configuration interface. or to select the language as required, and press to confirm.
Thermal Image Scope User Manual Chapter 11 Unit Settings You can switch the unit for the distance measurement function. Steps 1. Hold to show the menu. 2. Select , and press to switch the unit. m and yard are selectable. 3. Hold the save settings and exit.
Thermal Image Scope User Manual Chapter 12 Maintenance This part introduces the operation of checking device information, upgrading device, and restoring to defaults, etc. 12.1 View Device Information Steps 1. Hold 2. Select to show the menu of device. , and press . You can view the device information such as version, and serial No. 12.2 Upgrade Device Before You Start ● Please get the upgrade package (including Main Firmware and FPGA Firmware) first. ● Make sure the hotspot function is disabled.
Thermal Image Scope User Manual Chapter 13 Frequently Asked Questions 13.1 Why is the monitor off? Check whether the device is off-battery. Check the monitor after charging the device for 5 minutes. 13.2 The image is not clear, how to adjust it? Adjust the diopter adjustment knob until the image is clear. Refer to section Adjust Diopter. 13.3 Capturing or recording fails. What's the problem? Check the following items. ● Whether the device is connected to your PC.
