Digital Night Vision Scope User Manual
Digital Night Vision Scope User Manual Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the company website.
Digital Night Vision Scope User Manual IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.
Digital Night Vision Scope User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Digital Night Vision Scope User Manual This product and - if applicable - the supplied accessories too are marked with "UKCA" and comply therefore with the following directives: Radio Equipment Regulations 2017, Electromagnetic Compatibility Regulations 2016, Electrical Equipment (Safety) Regulations 2016, the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
Digital Night Vision Scope User Manual brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. ce matériel est conforme aux limites de dose d'exposition aux rayonnements, CNR-102 énoncée dans un autre environnement. KC B급 기기: 이 기기는 가정용(B급) 전자파적합기기로써 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다.
Digital Night Vision Scope User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Digital Night Vision Scope User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Laws and Regulations ● Use of the product must be in strict compliance with the local electrical safety regulations. Transportation ● Keep the device in original or similar packaging while transporting it. ● Keep all wrappers after unpacking them for future use.
Digital Night Vision Scope User Manual ● ● ● ● DO NOT swallow the battery to avoid chemical burns. DO NOT place the battery in the reach of children. The battery cannot be charged with external power source directly. The device cannot be charged, please use the supplied charger to charge the battery. Maintenance ● If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Digital Night Vision Scope User Manual Table of Contents Chapter 1 Overview ........................................................................................................................ 1 1.1 Device Description ............................................................................................................ 1 1.2 Main Function ................................................................................................................... 1 1.3 Appearance ...........................
Digital Night Vision Scope User Manual 6.4 Prerecord Video .............................................................................................................. 17 6.5 Export Files ..................................................................................................................... 17 Chapter 7 Client Software Connection ......................................................................................... 19 Chapter 8 Language Settings ...........................................
Digital Night Vision Scope User Manual Chapter 1 Overview 1.1 Device Description The digital night vision scope can perform in all ambient light. It has an advanced HD sensor and a high resolution OLED display, which provides full-color clarity in daytime and classic black & white viewing at night. The device meets the needs of professional hunters who value traditions and seek technological superiority. 1.
Digital Night Vision Scope User Manual Figure 1-1 Device Appearance Table 1-1 Buttons and Components No. Description Function 1 Lens Cover Protect the lens. 2 Focus Ring Adjust the focus to find clear targets. 3 Power Key 4 Laser Key 5 Wheel 6 Fixing Ring 7 Diopter Adjustment Ring 8 Eyepiece 9 Type-C Interface 10 Infrared Light Help to view target clearly in dark environment. 11 Laser Range Finder Measure the distance with laser.
Digital Night Vision Scope User Manual Chapter 2 Preparation 2.1 Cable Connection Connect the device and power adaptor with a type-C cable to power on the device. Alternatively, connect the device and PC to export files. Steps 1. Lift the cable interface cover. 2. Connect the device and power adapter with a Type-C cable to power on the device. Alternatively, connect the device and PC to export files. Figure 2-1 Cable Connection 2.2 Install Battery Insert the batteries into the battery compartment.
Digital Night Vision Scope User Manual Figure 2-3 Install Battery 3. Turn the battery cover clockwise to tighten it. Figure 2-4 Close Battery Cover Note Remove the battery from the battery compartment if the device is not used for a long time. 2.3 Install Rail Insert the batteries into the battery compartment. Before You Start ● Turn off the device first. Use the Non-dust cloth to clean the device base and the rail. Steps 1. Align the installation holes on the device and the rail.
Digital Night Vision Scope User Manual Figure 2-5 Align Installation Holes 2. Insert the screws. Figure 2-6 Install Screws 3. Tighten the screws to secure the device. Figure 2-7 Tighten Screws 2.4 Power On/Off Power On When the battery is sufficiently charged, hold Power Off When the device is turned on, hold for about 2 seconds to power on the device. for 2 seconds to power off the device.
Digital Night Vision Scope User Manual Auto Power Off Set the auto power off time for your device, and then the device will automatically shut down as the set time. Steps 1. Hold the wheel to go to the menu. 2. Rotate the wheel to select , and press the wheel to select the auto power off time as required. 3. Hold the wheel to save and exit. Note ● See the battery icon for the battery status. means the battery is fully charged, and means that the battery is low.
Digital Night Vision Scope User Manual Chapter 3 Image Settings 3.1 Adjust Diopter Steps 1. Power on the device. 2. Open the lens cover. 3. Hold the device and make sure the eyepiece covers your eye. 4. Rotate the adjust ring until the OSD text or image is clear. Figure 3-1 Adjust Diopter Note When adjusting diopter, DO NOT touch the surface of lens to avoid smearing the lens. 3.2 Adjust Focus Steps 1. Power on the device. 2. Hold the device and make sure the eyepiece covers your eye. 3.
Digital Night Vision Scope User Manual Figure 3-2 Adjust Focus Note When focusing, do not touch the surface of lens to avoid smearing the lens. 3.3 Adjust Brightness In menu mode, rotate the wheel to select and press the wheel to adjust brightness. 3.4 Adjust Contrast In menu mode, rotate the wheel to select and press the wheel to adjust image contrast. 3.5 Set Smart IR Image overexposure may occur in too bright environment.
Digital Night Vision Scope User Manual Day Night Auto Defog Figure 3-3 Display Mode 3.7 Adjust Digital Zoom In the live view interface, rotate the wheel to switch the digital zoom of the device. The value of digital zoom can be set to 1×, 2×, 4×, and 8×. 3.8 Set Picture in Picture Mode Steps 1. In the view mode, hold the wheel to show the menu. 2. Select , and press the wheel to enable the PIP function. The details are shown at the upcenter of the image.
Digital Night Vision Scope User Manual Note ● When reticle is enabled, the PIP view is the detail of reticle. When reticle is not enabled, the PIP view is the detail of central part. ● If digital zoom is enabled, the PIP view also zooms. If the digital zoom ratio exceeds 4, the PIP does not zoom. 3.9 Set OSD You can choose whether to display the OSD information on the live view interface in this function. Steps 1. Hold the wheel to show the menu. 2.
Digital Night Vision Scope User Manual Chapter 4 Aiming Point Settings 4.1 Select Reticle Group If different users use the same device, the users can configure and save the reticle settings in their respective reticle group. Steps 1. In the view mode, hold the wheel to show the menu. 2. Rotate the wheel to select . 3. Press the wheel to switch the reticle group. 4. Hold the wheel to save and exit. Result The right top of the image displays the reticle information.
Digital Night Vision Scope User Manual position for the reticle. Before You Start Select a reticle group first. Steps 1. In the view mode, hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the reticle setting interface. 3. Press the wheel to select a reticle No. You can select OFF to disable the reticle. 4. Set reticle type. 1) In the reticle setting interface, rotate the wheel to select Type. 2) Press the wheel to select a reticle type.
Digital Night Vision Scope User Manual Figure 4-2 PIP Effect in Reticle Mode 4.3 Correct Reticle Correcting the reticle can help you aim at the target with high accuracy by marking the offset between the big reticle and small reticle. Before You Start Select a reticle group first. Steps 1. In the view mode, hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the reticle setting interface. 3. Press the wheel to select a reticle No. you want to correct. 4.
Digital Night Vision Scope User Manual indicates the initial position of the reticle. 7. (Optional) Repeat 3 to 6 to set the position for other reticles in this group. Note When you switch the reticle No., a prompt will appear on the interface. Select OK to save the parameters for the current reticle. 7. Hold the wheel to exit the interface according to the prompt. – OK: Save the parameter and exit. – Cancel: Exit but not save the parameters.
Digital Night Vision Scope User Manual Chapter 5 Measure Distance The device can detect the distance between the target and the observation position with laser. Before You Start When measuring the distance, keep the hand and the position steady. Otherwise, the accuracy may be affected. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the laser ranging setting interface. 3. Press the wheel to enable Laser Ranging. 4.
Digital Night Vision Scope User Manual Chapter 6 Picture and Video You can manually record video or capture picture when displaying live view. 6.1 Capture Picture In the main live view interface, press and wheel at the same time to capture images. Note When capturing succeeds, the image freezes for 1 second and a prompt shows on the display. For exporting captured pictures, refer to Export Files. 6.2 Set Audio If you enable the audio function, the sound will be recorded with the video.
Digital Night Vision Scope User Manual Figure 6-1 Start Recording The left top of image displays the information of recording time. 2. Press the wheel again to stop recording. What to do next For exporting recording files, refer to Export Files. 6.4 Prerecord Video After you enable this function and select the prerecording time, the device can automatically start recording the 7, 10 or 15 seconds before the recoil-activation and end recording the 7, 10 or 15 seconds after the recoil-activation. Steps 1.
Digital Night Vision Scope User Manual Before You Start ● Turn off the hotspot function. ● Turn on the device after connecting it to your PC, and keep the device on for 10 to 15 seconds before other operations. Steps 1. Connect the device and PC with a Type-C cable. Note Make sure the device is turned on when connecting the cable. 2. Open computer disk and select the disk of device. Go to the DCIM folder and find the folder named after the capture year and month.
Digital Night Vision Scope User Manual Chapter 7 Client Software Connection Connect the device to the T-Vision App via hotspot, then you can capture picture, record video, or configure parameters on your phone. Steps 1. Hold the wheel to show the menu of device. 2. Press to enable hotspot function. 3. Turn on the WLAN of your phone and connect to the hotspot. ● Hotspot Name: Wlan-IPTS Serial No. ● Hotspot Password: the last 9 digits of serial No. 4. Scan the QR code to download and install the App.
Digital Night Vision Scope User Manual Chapter 8 Language Settings You can select the device language in this function. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the language configuration interface. 3. Rotate the wheel to select the language as required, and press the wheel to confirm.
Digital Night Vision Scope User Manual Chapter 9 Unit Settings You can switch the unit for the distance measurement function and the reticle function. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to switch the unit. Yard and m are selectable. 3. Hold the wheel to save settings and exit.
Digital Night Vision Scope User Manual Chapter 10 Maintenance This part introduces the operation of checking device information, upgrading device, and restoring to defaults, etc. 10.1 View Device Information Steps 1. Hold the wheel to show the menu of device. 2. Select , and press the wheel. You can view the device information such as version, and serial No. 10.2 Upgrade Device Before You Start ● Please get the upgrade package first. ● Make sure the hotspot function is disabled.
Digital Night Vision Scope User Manual Chapter 11 Frequently Asked Questions 11.1 Why is the monitor off? Check whether the device is off-battery. Connect the device to power supply and turn it on to check the monitor. 11.2 The image is not clear, how to adjust it? Adjust the diopter adjustment knob until the image is clear. Refer to section . 11.3 Capturing or recording fails. What's the problem? Check the following items. ● Whether the device is connected to your PC.
UD30125N