AGM Neith DIGITAL RIFLE SCOPE / CLIP-ON
Digital Rifle Scope / Clip-On User Manual Legal Information Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Digital Rifle Scope / Clip-On User Manual CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Digital Rifle Scope / Clip-On User Manual EU Conformity Statement his product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Directive 2014/30/EU (EMCD), Directive 2014/35/EU (LVD), Directive 2011/65/EU (RoHS). Directive 2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Digital Rifle Scope / Clip-On User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Digital Rifle Scope / Clip-On User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Laws and Regulations ● Use of the product must be in strict compliance with the local electrical safety regulations. Transportation ● Keep the device in original or similar packaging while transporting it. ● Keep all wrappers after unpacking them for future use.
Digital Rifle Scope / Clip-On User Manual ● ● ● ● ● DO NOT swallow the battery to avoid chemical burns. DO NOT place the battery in the reach of children. The battery cannot be charged with external power source directly. The device cannot be charged, please use the supplied charger to charge the battery. Please purchase the adapter by yourself. The using environment of the adapter should be consistent with that of the device.
Digital Rifle Scope / Clip-On User Manual COMPLIANCE NOTICE: The thermal series products might be subject to export controls in various countries or regions, including without limitation, the United States, European Union, United Kingdom and/or other member countries of the Wassenaar Arrangement.
Handheld Thermal Monocular Camera User Manual Table of Contents Chapter 1 Overview.................................................................................................................... 1 1.1 Device Description................................................................................................................. 1 1.2 Main Function ........................................................................................................................ 1 1.3 Appearance ................
Handheld Thermal Monocular Camera User Manual 6.2 Set Audio.............................................................................................................................. 14 6.3 Record Video ....................................................................................................................... 14 6.4 Prerecord Video ................................................................................................................... 15 6.5 Export Files ...........................
Handheld Thermal Monocular Camera User Manual Chapter 1 Overview 1.1 Device Description The digital night vision scope can perform in all ambient light. It has an advanced HD sensor and a high resolution OLED display, which provides full-color clarity in daytime and classic black & white viewing at night. The traditional-style tube meets the needs of professional hunters who value traditions and seek technological superiority. 1.
Handheld Thermal Monocular Camera User Manual Figure 1-1 Device Appearance Table 1-1 Buttons and Components No. Description Function 1 Lens Cover Protect the lens. 2 Focus Ring Adjust the focus to find clear targets. 3 Power Key 4 Measure Key 5 Wheel 6 Fixing Ring Fix the eyepiece. 7 Diopter Adjustment Ring Adjust the dioptric correction. 8 Eyepiece View the target. 9 Data Exchange Interface Connect the device to power supply or transmit data with a type-C cable.
Handheld Thermal Monocular Camera User Manual Chapter 2 Preparation 2.1 Cable Connection Connect the device and power adaptor with a type-C cable to power on the device. Alternatively, connect the device and PC to export files. Steps 1. Lift the cable interface cover. 2. Connect the device and power adapter with a Type-C cable to power on the device. Alternatively, connect the device and PC to export files. 2.2 Install Battery Insert the batteries into the battery compartment. Steps 1.
Handheld Thermal Monocular Camera User Manual 2.4 Power On/Off Power On When the battery is sufficiently charged, hold Power Off When the device is turned on, hold for about 2 seconds to power on the device. for 2 seconds to power off the device. Auto Power Off Set the auto power off time for your device, and then the device will automatically shut down as the set time. Steps 1. Hold the wheel to go to the menu. 2.
Handheld Thermal Monocular Camera User Manual Chapter 3 Image Settings 3.1 Adjust Diopter Steps 1. Power on the device. 2. Open the lens cover. 3. Hold the device and make sure the eyepiece covers your eye. 4. Rotate the adjust ring until the OSD text or image is clear. Note When adjusting diopter, DO NOT touch the surface of lens to avoid smearing the lens. 3.2 Adjust Focus Steps 1. Power on the device. 2. Hold the device and make sure the eyepiece covers your eye. 3.
Handheld Thermal Monocular Camera User Manual 3.5 Set Smart IR Image overexposure may occur in too bright environment. The smart IR function helps to adjust the overexposed images, and it can improve the image effect in night mode by adjusting the brightness of the supplement light. In menu mode, rotate the wheel to select and press the wheel to enable this function. 3.6 Set Display Mode You can select different display modes in different scenes. Hold in live view interface to switch display modes.
Handheld Thermal Monocular Camera User Manual Figure 3-3 PIP Effect 4. Hold the wheel to exit. Note ● When reticle is enabled, the PIP view is the detail of reticle. When reticle is not enabled, the PIP view is the detail of central part. ● If digital zoom is enabled, the PIP view also zooms. If the digital zoom ratio exceeds 4, the PIP does not zoom. 3.9 Set OSD You can choose whether to display the OSD information on the live view interface in this function. Steps 1. Hold the wheel to show the menu. 2.
Handheld Thermal Monocular Camera User Manual 5. Hold the wheel to save settings and exit. 3.10 Set Brand Logo You can add brand logo on the live view interface. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select . 3. Press the wheel to enable Brand Logo. 4. Hold the wheel to save the settings and exit. Result The brand logo is displayed at the right bottom of the image and video.
Handheld Thermal Monocular Camera User Manual Chapter 4 Aiming Point Settings 4.1 Select Reticle Group If different users use the same device, the users can configure and save the reticle settings in their respective reticle group. Steps 1. In the view mode, hold the wheel to show the menu. 2. Rotate the wheel to select . 3. Press the wheel to switch the reticle group. 4. Hold the wheel to save and exit. Result The right top of the image displays the reticle information.
Handheld Thermal Monocular Camera User Manual position for the reticle. Before You Start Select a reticle group first. Steps 1. In the view mode, hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the reticle setting interface. 3. Press the wheel to select a reticle No. You can select OFF to disable the reticle. 4. Set reticle type. 1) In the reticle setting interface, rotate the wheel to select Type. 2) Press the wheel to select a reticle type.
Handheld Thermal Monocular Camera User Manual Figure 4-2 PIP Effect in Reticle Mode 4.3 Correct Reticle Correcting the reticle can help you aim at the target with high accuracy by marking the offset between the big reticle and small reticle. Before You Start Select a reticle group first. Steps 1. In the view mode, hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the reticle setting interface. 3. Press the wheel to select a reticle No. you want to correct. 4.
Handheld Thermal Monocular Camera User Manual indicates the initial position of the reticle. 7. (Optional) Repeat 3 to 6 to set the position for other reticles in this group. Note When you switch the reticle No., a prompt will appear on the interface. Select OK to save the parameters for the current reticle. 7. Hold the wheel to exit the interface according to the prompt. – OK: Save the parameter and exit. – Cancel: Exit but not save the parameters.
Handheld Thermal Monocular Camera User Manual Chapter 5 Measure Distance The device can detect the distance between the target and the observation position. Before You Start When measuring the distance, keep the hand and the position steady. Otherwise, the accuracy may be affected. Steps 1. Hold the wheel to show the menu. 2. Select and press the wheel to go to the setting interface. 1) Rotate the wheel to select the target from Deer, Grey Wolf, Brown Bear, and Custom.
Handheld Thermal Monocular Camera User Manual Chapter 6 Picture and Video You can manually record video or capture picture when displaying live view. 6.1 Capture Picture In the main live view interface, press and wheel at the same time to capture images. Note When capturing succeeds, the image freezes for 1 second and a prompt shows on the display. For exporting captured pictures, refer to Export Files. 6.2 Set Audio If you enable the audio function, the sound will be recorded with the video.
Handheld Thermal Monocular Camera User Manual Figure 6-1 Start Recording The left top of image displays the information of recording time. 2. Press the wheel again to stop recording. What to do next For exporting recording files, refer to Export Files. 6.4 Prerecord Video After you enable this function and select the prerecording time, the device can automatically start recording the 7, 10 or 15 seconds before the recoil-activation and end recording the 7, 10 or 15 seconds after the recoil-activation.
Handheld Thermal Monocular Camera User Manual Before You Start ● Turn off the hotspot function. ● Turn on the device after connecting it to your PC, and keep the device on for 10 to 15 seconds before other operations. Steps 1. Connect the device and PC with a Type-C cable. Note Make sure the device is turned on when connecting the cable. 2. Open computer disk and select the disk of device. Go to the DCIM folder and find the folder named after the capture year and month.
Handheld Thermal Monocular Camera User Manual Chapter 7 Client Software Connection Connect the device to the T-Vision App via hotspot, then you can capture picture, record video, or configure parameters on your phone. Steps 1. Hold to show the menu of device. 2. Press to enable hotspot function. 3. Turn on the WLAN of your phone and connect to the hotspot. ● Hotspot Name: Wlan-IPTS Serial No. ● Hotspot Password: the last 9 digits of serial No. 4.
Handheld Thermal Monocular Camera User Manual Chapter 8 Language Settings You can select the device language in this function. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the language configuration interface. 3. Rotate the wheel to select the language as required, and press the wheel to confirm.
Handheld Thermal Monocular Camera User Manual Chapter 9 Unit Settings You can switch the unit for the distance measurement function and the reticle function. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to switch the unit. Yard and m are selectable. 3. Hold the wheel to save settings and exit.
Handheld Thermal Monocular Camera User Manual Chapter 10 Maintenance This part introduces the operation of checking device information, upgrading device, and restoring to defaults, etc. 10.1 View Device Information Steps 1. Hold the wheel to show the menu of device. 2. Select , and press the wheel. You can view the device information such as version, and serial No. 10.2 Upgrade Device Before You Start ● Please get the upgrade package (including Main Firmware and FPGA Firmware) first.
Handheld Thermal Monocular Camera User Manual Chapter 11 Frequently Asked Questions 11.1 Why is the monitor off? Check whether the device is off-battery. Check the monitor after charging the device for 5 minutes. 11.2 The image is not clear, how to adjust it? Adjust the diopter adjustment knob until the image is clear. Refer to section 3.1. 11.3 Capturing or recording fails. What's the problem? Check the following items. ● Whether the device is connected to your PC.
