QUICK HITCH PART # 25-005, CAT 1 QUICK HITCH PART # 25-010, CAT 2 QUICK HITCH PART # 25-019, CAT 2HD QUICK HITCH PART # 25-020, CAT 3 QUICK HITCH PART # 25-021, CAT 3 NARROW QUICK HITCH PART # 25-022, CAT 2/3 QUICK HITCH Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious injury or death.
TABLE OF CONTENTS Intended Use ......................................................................4 Personal Protective Equipment ..........................................4 General Safety ....................................................................5 Assembly Instructions ........................................................6 Operation Instructions ........................................................8 Removal Instructions........................................................
IMPORTANT SAFETY INFORMATION WARNING: Read and thoroughly understand all instructions and safety information before assembling or operating this quick hitch. Failure to do so may cause serious injury or death. Do not allow anyone to operate this quick hitch who has not read this manual. A quick hitch can be dangerous if assembled or used improperly. Do not operate if you have doubts or questions concerning safe operation.
IMPORTANT SAFETY INFORMATION GENERAL SAFETY Failure to follow warnings, cautions, assembly and operation instructions in the Operation Manual may result in serious injury or death. Read the Operation Manual before operation. ● Do not permit children to operate this equipment at any time. Do not permit others that have not read and understood the complete Operation Manual to operate this equipment.
ASSEMBLY INSTRUCTIONS INSTRUCTIONS TO ATTACH THE 3-PT OF THE TRACTOR TO THE QUICK HITCH STEP 1: Lower the tractor lift arms. Place the tractor lift arms within the slot of the quick hitch and align the holes. The model CAT 2/3 has two slots to connect the tractor a-arms. The inside slot is for CAT 2 tractors and the outside slot is for CAT 3 tractors. STEP 2: Connect the a-arm to the quick hitch using the lower a-arm pin B and lynch pin.
ASSEMBLY INSTRUCTIONS STEP 4: Connect the top link B with the top link pin and lynch pin. C INSTRUCTIONS TO ATTACH THE IMPLEMENT TO THE QUICK HITCH STEP 1: Bushings might be required to connect your implement to the quick hitch. Bushings are required if the diameter of the implements lower hitch pin is smaller than the lower hooks of the quick hitch. Attach the bushings to the implements lower hitch pins by sliding on the bushing. Secure the bushing to the implements lower hitch pins with roll pins.
OPERATING INSTRUCTIONS STEP 2: Move the tractor to position the quick hitch's lower hooks below the implements bushings or lower hitch pin. Position the hook of the quick hitch below the mast pin of the implement. STEP 3: Raise the a-arms of the tractor to lift the implement. Verify that the bushings or lower hitch pins set completely within the quick hitch lower hooks and the mast pin captured by the quick hitch upper hook.
OPERATING INSTRUCTIONS Some Non-standard CAT 1 implements may require the use of the CAT 1 quick hitch adapter. Follow the below steps to attach the quick hitch to non-standard implements. STEP 1: Remove the upper hook by removing the hex bolts and nuts. STEP 2: Slide the adapter bracket over the top bracket of the quick hitch and put the top link pin through both the quick hitch adapter and top link. Either hole of the quick hitch adapter can be used.
OPERATING INSTRUCTIONS INSTRUCTIONS TO REMOVE THE IMPLEMENT FROM THE QUICK HITCH STEP 1: Turn off the tractor and remove the PTO driveline if applicable. See the tractor's owner's manual for instructions. Raise the tractor a-arms enough that the implement weight is on the quick hitch hooks. Flip both quick hitch handles vertical. The handles will stay vertical or in the open position.
MAINTENANCE ALWAYS PERFORM MAINTENANCE OPERATIONS WITH THE TRACTOR’S ENGINE POWERED OFF, AND PTO DISENGAGED. Clean dirt and debris off the quick hitch after each use. Store the quick hitch in a clean and dry location. Lubricate all moving parts periodically. Check for damaged or worn parts after each use. Do not attach the quick hitch to a tractor or implement if parts are warn and need to be replaced.
QUICK HITCH PARTS LIST CAT 1 QUICK HITCH P/N: 25-005 ITEM NO. PART NUMBER PAGE 12 DESCRIPTION QTY.
QUICK HITCH PARTS LIST *The photo may not be an accurate representation of the quick hitch or sub parts. CAT 2 P/N: 25-010 CAT 2 HD P/N: 25-019 ITEM NO. CAT 3 P/N: 25-020 CAT 3N P/N: 25-021 CAT 2/3 P/N: 25-022 PART NUMBER DESCRIPTION QTY.
WARRANTY IMPORTANT NOTICE We, the manufacturer, reserve the right to change the product and/ or specifications in this manual without notification. The manual is for information use only and the pictures and drawings depicted herein are for reference only. Warranty Repair and Service Do not return this product to the store for warranty issues or repair. Call our customer service department at 303-278-0664 for the location of the nearest service center. Record the information below for future reference.
REGISTRATION Acceptance of responsibility: I (purchaser) have read the Operation Manual and Limited Warranty or someone has read and explained all instructions to me. I understand this warranty does not cover any labor and that all disputes will be settled by binding arbitration. Warranty void if any attempt to repair or replace defective parts has been made by unauthorized personnel. The mark next to each item below confirms my acceptance of responsibility for the use and maintenance of this quick hitch.
REGISTRATION WARRANTY VOID IF REGISTRATION IS NOT POST MAKED WITHIN 15 DAYS OF PURCHASE.
