U2802A QSG.
U2802A QSG.book Page II Tuesday, January 8, 2008 10:54 AM Safety Information This 31-channel thermocouple input device is safety-certified in compliance with: • IEC 61326:2002 / EN 61326:1997+A1:1998+A2:2001+A3:2003 • CISPR 11: 1990/EN55011:1990 [Radiated emission] • CANADA: ICES-001: 2004 • Australia/New Zealand: AS/NZS CISPR11:2004 WARN IN G A WARNING notice denotes a hazard.
U2802A QSG.book Page III Tuesday, January 8, 2008 10:54 AM CAU T ION • • • • • • • Do not load the input and output terminals above the specified operating limits. Input terminals should not exceed ±10 V with respect to the module ground. Applying excessive voltage or overloading the device will cause irreversible damage to the circuitry. Applying excessive voltage or overloading the input terminal will damage the device permanently.
U2802A QSG.book Page IV Tuesday, January 8, 2008 10:54 AM Regulatory Markings The CE mark is a registered trademark of the European community. This CE mark shows that the product complies with all the relevant European legal directive. ICES/NMB-001 indicates that this ISM device complies with Canadian ICES-001. The CSA mark is a registered trademark of the Canadian Standards Association. A CSA mark with the indicators "C" and "US" means that the product is certified for both the U.S.
U2802A QSG.book Page V Tuesday, January 8, 2008 10:54 AM Safety Symbols Direct current Alternating current Both direct and alternating current Three-phase alternating current Earth (ground) terminal Protective conductor terminal Frame or chassis terminal Equipotentiality On (Supply) Off (Supply) Equipment protected throughout by double insulation or reinforced insulation Caution, risk of electric shock Caution, hot surface Caution, risk of danger (See note.
U2802A QSG.
U2802A QSG.book Page 1 Tuesday, January 8, 2008 10:54 AM Contents Introduction to Agilent U2802A 2 Standard Purchase Items Checklist 3 Product Overview 4 General Specifications 6 Installations and Configurations 7 A. Check Your System Requirements 9 B. Check Your Pre-Installed IO Libraries Suite 10 C. Install the Agilent IO Libraries Suite Version 14.2 or Higher 11 D. Install the DAQ Hardware Driver 12 E. Install the Agilent Measurement Manager 13 F. Connect Your DAQ Device to the PC 17 G.
U2802A QSG.book Page 2 Tuesday, January 8, 2008 10:54 AM Introduction to Agilent U2802A The Agilent U2802A 31- Channel Thermocouple Input is a thermocouple input device that functions to convert low input voltage signal (< ±100 mV) from a thermocouple into an output voltage range suitable for data acquisition (DAQ) device (± 10 V). Agilent U2802A thermocouple is to be used in conjunction with the U2355A and U2356A model DAQ to enable a wide range of sensor input measurements.
U2802A QSG.book Page 3 Tuesday, January 8, 2008 10:54 AM Standard Purchase Items Checklist Inspect and verify that you have all the following items upon standard purchase of U2802A 31- channel thermocouple input device. If there are missing items, contact the nearest Agilent Sales Office.
U2802A QSG.
U2802A QSG.
U2802A QSG.
U2802A QSG.book Page 7 Tuesday, January 8, 2008 10:54 AM Installations and Configurations The U2802A is used in conjunction with the U2355A and U2356A DAQ. If you are using the U2300A Series with the Agilent Measurement Manager, follow the step- by- step instructions as shown in the following flowchart.
U2802A QSG.book Page 8 Tuesday, January 8, 2008 10:54 AM A. Check Your System Requirements B. Check Your Pre-Installed IO Libraries Suite ii. If Agilent IO Libraries Suite 14.2 has been pre-installed i. If Agilent IO Libraries Suite version 14.1 or lower has been pre-installed (requires uninstalling of this version) iii. If Agilent IO Libraries Suite is not installed C. Install the Agilent IO Libraries Suite Version 14.2 or Higher D. Install the DAQ Hardware Driver E.
U2802A QSG.book Page 9 Tuesday, January 8, 2008 10:54 AM A. Check Your System Requirements Before installing the Agilent Measurement Manager software and DAQ hardware driver, make sure your PC meets the following minimum system requirements for installation and data acquisition. Processor 1.
U2802A QSG.book Page 10 Tuesday, January 8, 2008 10:54 AM B. Check Your Pre-Installed IO Libraries Suite To check the version of your pre- installed IO Libraries Suite, follow the instructions below. 1 Right- click IO Control icon on your taskbar notification area and the context menu will appear as shown below. Select About Agilent IO Control. 2 Agilent IO Control window will appear and the version of installed IO Libraries Suite will be displayed as shown below.
U2802A QSG.book Page 11 Tuesday, January 8, 2008 10:54 AM i. If Agilent IO Libraries Suite version 14.1 or lower has been pre-installed If you have Agilent IO Libraries Suite version 14.1 or lower installed on your PC, you are required to uninstall the IO Libraries Suite. 1 To perform uninstallation, go to Start > Control Panel > Add or Remove Programs. The Add or Remove Programs window will appear. Select Agilent IO Libraries Suite 14.1 or lower version.
U2802A QSG.book Page 12 Tuesday, January 8, 2008 10:54 AM 1 Disconnect any USB DAQ device that is connected to your PC and close all other applications on your PC. 2 Insert the Agilent Automation- Ready CD into your CD- ROM drive, and follow the instructions on your screen. 3 If the installation does not start automatically, go to Start > Run (on the Windows start menu) and type :\autorun\auto.exe where drive is your CD- ROM drive.
U2802A QSG.book Page 13 Tuesday, January 8, 2008 10:54 AM E. Install the Agilent Measurement Manager N O TE Make sure Agilent Measurement Manager version 1.4 and above is installed before U2802A is used. 1 Verify that you have the hardware driver installed. If not, close all other applications on your PC and insert the Product Reference CD- ROM into your CD- ROM drive. 2 Click Measurement Manager on the Agilent Modular Products Installation Menu to begin the installation.
U2802A QSG.book Page 14 Tuesday, January 8, 2008 10:54 AM 5 If you do not have the Agilent T&M Toolkit 2.1 Runtime version and/or Microsoft .NET Framework version 1.1 and 2.0 installed, the InstallShield Wizard software pre- requisite will appear as shown below. 6 Click OK to begin installation of the listed missing software.
U2802A QSG.book Page 15 Tuesday, January 8, 2008 10:54 AM 9 Read the License Agreement and select I accept the terms in the License Agreement to proceed. You may click Print to print a hardcopy of the Agilent License Terms for reference. Click Next to proceed. 10 Fill in the Customer Information form, as shown below, accordingly and click Next. 11 Click Next to install to the folder specified or click Change to install to a different folder.
U2802A QSG.book Page 16 Tuesday, January 8, 2008 10:54 AM 12 Click Install to begin the installation of Agilent Measurement Manager. 13 Click Finish when the installation has completed. 14 A shortcut to this software will be created on your desktop. N O TE 16 USING THE LICENSED MATERIALS INDICATES YOUR ACCEPTANCE OF THE LICENSE TERMS. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, YOU MAY RETURN ANY UNOPENED LICENSED MATERIALS FOR A FULL REFUND.
U2802A QSG.book Page 17 Tuesday, January 8, 2008 10:54 AM F. Connect Your DAQ Device to the PC N O TE Refer to Agilent U2300A Series USB Multifunction Data Acquisition Devices User’s Guide for “Connect Your DAQ Device to PC” procedure. The bundled power supply splitter in U2802A is used to allow powering both the U2802 and U2355/56A DAQ with a single DC power adapter which has been supplied with the DAQ. G.
U2802A QSG.book Page 18 Tuesday, January 8, 2008 10:54 AM I. Launch Your Agilent Measurement Manager N O TE • • • The Agilent IO Control will launch automatically when you start your PC. Launching Agilent Measurement Manager without Agilent IO Control running will cause Agilent Measurement Manager to fail from detecting or establishing any connection with the USB DAQ device connected to your PC. To run Agilent IO Control, go to Start > All Programs > Agilent IO Libraries Suite > Utilities > IO Control.
U2802A QSG.book Page 23 Tuesday, January 8, 2008 10:54 AM www.agilent.
