Programming instructions
Table Of Contents
- Programming Guide
- Table of Contents
- 1 Getting Started
- 2 Programming Examples
- Using the Programming Examples
- GPIB Programming Examples
- Before Using the Examples
- Interface Check using Agilent BASIC
- Interface Check Using NI-488.2 and C++
- Interface Check using VISA and C
- Local Lockout Using Agilent BASIC
- Local Lockout Using NI-488.2 and C++
- Queries Using Agilent BASIC
- Queries Using NI-488.2 and C++
- Queries Using VISA and C
- Generating a CW Signal Using VISA and C
- Generating an Externally Applied AC-Coupled FM Signal Using VISA and C
- Generating an Internal AC-Coupled FM Signal Using VISA and C
- Generating a Step-Swept Signal Using VISA and C
- Saving and Recalling States Using VISA and C
- Reading the Data Questionable Status Register Using VISA and C
- Reading the Service Request Interrupt (SRQ) Using VISA and C
- LAN Programming Examples
- RS-232 Programming Examples
- 3 Programming the StatusRegisterSystem
- 4 Command Reference
- Command Reference Information
- SCPI Basics
- IEEE 488.2 Common Commands
- Calibration subsystem
- Communication Subsystem
- Diagnostic Subsystem
- Display Subsystem
- Memory Subsystem
- Mass Memory Subsystem
- Output Subsystem
- Status Subsystem
- :OPERation:CONDition
- :OPERation:ENABle
- :OPERation:NTRansition
- :OPERation:PTRansition
- :OPERation[:EVENt]
- :PRESet
- :QUEStionable:CALibration:CONDition
- :QUEStionable:CALibration:ENABle
- :QUEStionable:CALibration:NTRansition
- :QUEStionable:CALibration:PTRansition
- :QUEStionable:CALibration[:EVENt]
- :QUEStionable:CONDition
- :QUEStionable:ENABle
- :QUEStionable:FREQuency:CONDition
- :QUEStionable:FREQuency:ENABle
- :QUEStionable:FREQuency:NTRansition
- :QUEStionable:FREQuency:PTRansition
- :QUEStionable:FREQuency[:EVENt]
- :QUEStionable:MODulation:CONDition
- :QUEStionable:MODulation:ENABle
- :QUEStionable:MODulation:NTRansition
- :QUEStionable:MODulation:PTRansition
- :QUEStionable:MODulation[:EVENt]
- :QUEStionable:NTRansition
- :QUEStionable:POWer:CONDition
- :QUEStionable:POWer:ENABle
- :QUEStionable:POWer:NTRansition
- :QUEStionable:POWer:PTRansition
- :QUEStionable:POWer[:EVENt]
- :QUEStionable:PTRansition
- :QUEStionable[:EVENt]
- System Subsystem
- Trigger Subsystem
- Unit Subsystem (:UNIT)
- Amplitude Modulation Subsystem
- :AM[1]|2...
- :AM:INTernal:FREQuency:STEP[:INCRement]
- :AM:MODE
- :AM[1]|2:EXTernal[1]|2:COUPling
- :AM[1]|2:EXTernal[1]|2:IMPedance
- :AM[1]|2:INTernal[1]:FREQuency:ALTernate
- :AM[1]|2:INTernal[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :AM[1]|2:INTernal[1]:SWEep:RATE
- :AM[1]|2:INTernal[1]:SWEep:TRIGger
- :AM[1]|2:INTernal[1]|2:FREQuency
- :AM[1]|2:INTernal[1]|2:FUNCtion:NOISe
- :AM[1]|2:INTernal[1]|2:FUNCtion:RAMP
- :AM[1]|2:INTernal[1]|2:FUNCtion:SHAPe
- :AM[1]|2:SOURce
- :AM[1]|2:STATe
- :AM[1]|2:TYPE
- :AM[1]|2[:DEPTh]:EXPonential
- :AM[1]|2[:DEPTh][:LINear]
- :AM[1]|2[:DEPTh][:LINear]:TRACk
- :AM[:DEPTh]:STEP[:INCRement]
- Correction Subsystem ([:SOURce]:CORRection)
- Frequency Subsystem ([:SOURce])
- Frequency Modulation Subsystem ([:SOURce])
- :FM[1]|2...
- :FM:INTernal:FREQuency:STEP
- :FM[1]|2:EXTernal[1]|2:COUPLing
- :FM[1]|2:EXTernal[1]|2:IMPedance
- :FM[1]|2:INTernal[1]:FREQuency:ALTernate
- :FM[1]|2:INTernal[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :FM[1]|2:INTernal[1]:SWEep:RATE
- :FM[1]|2:INTernal[1]:SWEep:TRIGger
- :FM[1]|2:INTernal[1]|2:FREQuency
- :FM[1]|2:INTernal[1]|2:FUNCtion:NOISe
- :FM[1]|2:INTernal[1]|2:FUNCtion:RAMP
- :FM[1]|2:INTernal[1]|2:FUNCtion:SHAPe
- :FM[1]|2:SOURce
- :FM[1]|2:STATe
- :FM[1]|2[:DEViation]
- :FM[1]|2[:DEViation]:TRACk
- List/Sweep subsystem ([:SOURce])
- Low Frequency Output Subsystem ([:SOURce]:LFOutput)
- :AMPLitude
- :FUNCtion[1]:FREQuency:ALTernate
- :FUNCtion[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :FUNCtion[1]:SWEep:RATE
- :FUNCtion[1]:SWEep:TRIGger
- :FUNCtion[1]|2:FREQuency
- :FUNCtion[1]|2:SHAPe
- :FUNCtion:NOISe
- :FUNCtion[1]|2:SHAPe:RAMP
- :SOURce
- LF Out softkeys:LF Out Off On;low frequency output subsystem keys:LF Out Off On
- Phase Modulation subsystem
- :PM[1]|2...
- :PM:INTernal:FREQuency:STEP[:INCRement]
- :PM[1]|2:BANDwidth|BWIDth
- :PM[1]|2:EXTernal[1]|2:COUPling
- :PM[1]|2:EXTernal[1]|2:IMPedance
- :PM[1]|2:INTernal[1]:FREQuency:ALTernate
- :PM[1]|2:INTernal[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :PM[1]|2:INTernal[1]:SWEep:RATE
- :PM[1]|2:INTernal[1]:SWEep:TRIGger
- :PM[1]|2:INTernal[1]|2:FREQuency
- :PM[1]|2:INTernal[1]|2:FUNCtion:NOISe
- :PM[1]|2:INTernal[1]|2:FUNCtion:RAMP
- :PM[1]|2:INTernal[1]|2:FUNCtion:SHAPe
- :PM[1]|2:SOURce
- :PM[1]|2:STATe
- :PM[1]|2[:DEViation]
- :PM[1]|2[:DEViation]:TRACk
- :PM[:DEViation]:STEP[:INCRement]
- Power Subsystem ([:SOURce])
- :POWer:ALC:BANDwidth|BWIDth
- :POWer:ALC:BANDwidth|BWIDth:AUTO
- :POWer:ALC:LEVel
- :POWer:ALC:SEARch
- :POWer:ALC:SOURce
- :POWer:ALC:SOURce:EXTernal:COUPling
- :POWer:ALC[:STATe]
- :POWer:ATTenuation
- :POWer:ATTenuation:AUTO
- :POWer:MODE
- :POWer:REFerence
- :POWer:REFerence:STATe
- :POWer:STARt
- :POWer:STOP
- :POWer[:LEVel][:IMMediate]:OFFSet
- :POWer[:LEVel][:IMMediate][:AMPLitude]
- Pulse Modulation Subsystem ([:SOURce])
- SCPI Command Compatibility
- Index
Index
345
Ext1, 276
Ext2
, 276
FM ΦM Normal High BW
, 270
Free Run
, 273
Gaussian
, 274
Incr Set
, 270, 278
Internal 1
, 276
Internal 2
, 276
Negative
, 275
Noise
, 275
Positive
, 275
Ramp
, 275
Sine
, 275
Square
, 275
Swept-Sine
, 275
Triangle
, 275
Trigger Key
, 273
Uniform
, 274
Phase Ref Set softkey
, 241
ping program
, 15
polling method (status registers)
, 106
ports
, 69
Positive softkey
, 227, 250, 267, 275
positive transition filter, description
, 113
Power Meter softkey
, 165
Power On Last Preset softkey
, 210
Power Search Manual Auto softkey
, 280
power subsystem keys
100 Hz
, 279
1 kHz
, 279
10 kHz
, 279
100 kHz
, 279
ALC Off On
, 282
Ampl
, 283
Ampl Offset
, 286
Ampl Ref Off On
, 284
Ampl Ref Set
, 284
Ampl Start
, 285
Ampl Stop
, 285
Amplitude
, 283, 287
Atten Hold Off On
, 283
Auto
, 279
Do Power Search
, 280
Ext Detector
, 281
Ext Detector Coupling Factor
, 281
Internal
, 281
Power Search Manual Auto
, 280
Set ALC Level
, 280
Set Atten
, 282
Source Module
, 281
precise talking and forgiving listening
, 144
Preset hardkey
, 210
Preset List softkey
, 235, 261
Preset Normal User softkey
, 212
programming languages
, 32
pulse modulation subsystem keys
Ext Pulse
, 292
Incr Set
, 289
Int Doublet
, 292
Int Free-Run
, 292
Int Gated
, 292
Int Triggered
, 292
Internal Square
, 292
Pulse Delay
, 288
Pulse Off On
, 293
Pulse Period
, 290
Pulse Rate
, 289
Pulse Width
, 291
Pulse softkeys
Pulse Delay, 288
Pulse Off On
, 293
Pulse Period
, 290
Pulse Rate
, 289
Pulse Width
, 291
Q
quotes, SCPI command use of, 152
R
Ramp softkey, 227, 250, 266, 275
real response data
, 147
RECALL Reg softkey
, 158
Ref Oscillator Source Auto Off On softkey
, 243
register system overview
, 102
registers
See also status registers
condition, description
, 113
data questionable calibration condition
, 134
data questionable calibration event
, 134
data questionable calibration event enable
, 135
data questionable condition
, 121
data questionable event
, 122
data questionable event enable
, 123
data questionable frequency condition
, 128
data questionable frequency event
, 129
data questionable frequency event enable
, 129
data questionable modulation condition
, 131