Programming instructions
Table Of Contents
- Programming Guide
- Table of Contents
- 1 Getting Started
- 2 Programming Examples
- Using the Programming Examples
- GPIB Programming Examples
- Before Using the Examples
- Interface Check using Agilent BASIC
- Interface Check Using NI-488.2 and C++
- Interface Check using VISA and C
- Local Lockout Using Agilent BASIC
- Local Lockout Using NI-488.2 and C++
- Queries Using Agilent BASIC
- Queries Using NI-488.2 and C++
- Queries Using VISA and C
- Generating a CW Signal Using VISA and C
- Generating an Externally Applied AC-Coupled FM Signal Using VISA and C
- Generating an Internal AC-Coupled FM Signal Using VISA and C
- Generating a Step-Swept Signal Using VISA and C
- Saving and Recalling States Using VISA and C
- Reading the Data Questionable Status Register Using VISA and C
- Reading the Service Request Interrupt (SRQ) Using VISA and C
- LAN Programming Examples
- RS-232 Programming Examples
- 3 Programming the StatusRegisterSystem
- 4 Command Reference
- Command Reference Information
- SCPI Basics
- IEEE 488.2 Common Commands
- Calibration subsystem
- Communication Subsystem
- Diagnostic Subsystem
- Display Subsystem
- Memory Subsystem
- Mass Memory Subsystem
- Output Subsystem
- Status Subsystem
- :OPERation:CONDition
- :OPERation:ENABle
- :OPERation:NTRansition
- :OPERation:PTRansition
- :OPERation[:EVENt]
- :PRESet
- :QUEStionable:CALibration:CONDition
- :QUEStionable:CALibration:ENABle
- :QUEStionable:CALibration:NTRansition
- :QUEStionable:CALibration:PTRansition
- :QUEStionable:CALibration[:EVENt]
- :QUEStionable:CONDition
- :QUEStionable:ENABle
- :QUEStionable:FREQuency:CONDition
- :QUEStionable:FREQuency:ENABle
- :QUEStionable:FREQuency:NTRansition
- :QUEStionable:FREQuency:PTRansition
- :QUEStionable:FREQuency[:EVENt]
- :QUEStionable:MODulation:CONDition
- :QUEStionable:MODulation:ENABle
- :QUEStionable:MODulation:NTRansition
- :QUEStionable:MODulation:PTRansition
- :QUEStionable:MODulation[:EVENt]
- :QUEStionable:NTRansition
- :QUEStionable:POWer:CONDition
- :QUEStionable:POWer:ENABle
- :QUEStionable:POWer:NTRansition
- :QUEStionable:POWer:PTRansition
- :QUEStionable:POWer[:EVENt]
- :QUEStionable:PTRansition
- :QUEStionable[:EVENt]
- System Subsystem
- Trigger Subsystem
- Unit Subsystem (:UNIT)
- Amplitude Modulation Subsystem
- :AM[1]|2...
- :AM:INTernal:FREQuency:STEP[:INCRement]
- :AM:MODE
- :AM[1]|2:EXTernal[1]|2:COUPling
- :AM[1]|2:EXTernal[1]|2:IMPedance
- :AM[1]|2:INTernal[1]:FREQuency:ALTernate
- :AM[1]|2:INTernal[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :AM[1]|2:INTernal[1]:SWEep:RATE
- :AM[1]|2:INTernal[1]:SWEep:TRIGger
- :AM[1]|2:INTernal[1]|2:FREQuency
- :AM[1]|2:INTernal[1]|2:FUNCtion:NOISe
- :AM[1]|2:INTernal[1]|2:FUNCtion:RAMP
- :AM[1]|2:INTernal[1]|2:FUNCtion:SHAPe
- :AM[1]|2:SOURce
- :AM[1]|2:STATe
- :AM[1]|2:TYPE
- :AM[1]|2[:DEPTh]:EXPonential
- :AM[1]|2[:DEPTh][:LINear]
- :AM[1]|2[:DEPTh][:LINear]:TRACk
- :AM[:DEPTh]:STEP[:INCRement]
- Correction Subsystem ([:SOURce]:CORRection)
- Frequency Subsystem ([:SOURce])
- Frequency Modulation Subsystem ([:SOURce])
- :FM[1]|2...
- :FM:INTernal:FREQuency:STEP
- :FM[1]|2:EXTernal[1]|2:COUPLing
- :FM[1]|2:EXTernal[1]|2:IMPedance
- :FM[1]|2:INTernal[1]:FREQuency:ALTernate
- :FM[1]|2:INTernal[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :FM[1]|2:INTernal[1]:SWEep:RATE
- :FM[1]|2:INTernal[1]:SWEep:TRIGger
- :FM[1]|2:INTernal[1]|2:FREQuency
- :FM[1]|2:INTernal[1]|2:FUNCtion:NOISe
- :FM[1]|2:INTernal[1]|2:FUNCtion:RAMP
- :FM[1]|2:INTernal[1]|2:FUNCtion:SHAPe
- :FM[1]|2:SOURce
- :FM[1]|2:STATe
- :FM[1]|2[:DEViation]
- :FM[1]|2[:DEViation]:TRACk
- List/Sweep subsystem ([:SOURce])
- Low Frequency Output Subsystem ([:SOURce]:LFOutput)
- :AMPLitude
- :FUNCtion[1]:FREQuency:ALTernate
- :FUNCtion[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :FUNCtion[1]:SWEep:RATE
- :FUNCtion[1]:SWEep:TRIGger
- :FUNCtion[1]|2:FREQuency
- :FUNCtion[1]|2:SHAPe
- :FUNCtion:NOISe
- :FUNCtion[1]|2:SHAPe:RAMP
- :SOURce
- LF Out softkeys:LF Out Off On;low frequency output subsystem keys:LF Out Off On
- Phase Modulation subsystem
- :PM[1]|2...
- :PM:INTernal:FREQuency:STEP[:INCRement]
- :PM[1]|2:BANDwidth|BWIDth
- :PM[1]|2:EXTernal[1]|2:COUPling
- :PM[1]|2:EXTernal[1]|2:IMPedance
- :PM[1]|2:INTernal[1]:FREQuency:ALTernate
- :PM[1]|2:INTernal[1]:FREQuency:ALTernate:AMPLitude:PERCent
- :PM[1]|2:INTernal[1]:SWEep:RATE
- :PM[1]|2:INTernal[1]:SWEep:TRIGger
- :PM[1]|2:INTernal[1]|2:FREQuency
- :PM[1]|2:INTernal[1]|2:FUNCtion:NOISe
- :PM[1]|2:INTernal[1]|2:FUNCtion:RAMP
- :PM[1]|2:INTernal[1]|2:FUNCtion:SHAPe
- :PM[1]|2:SOURce
- :PM[1]|2:STATe
- :PM[1]|2[:DEViation]
- :PM[1]|2[:DEViation]:TRACk
- :PM[:DEViation]:STEP[:INCRement]
- Power Subsystem ([:SOURce])
- :POWer:ALC:BANDwidth|BWIDth
- :POWer:ALC:BANDwidth|BWIDth:AUTO
- :POWer:ALC:LEVel
- :POWer:ALC:SEARch
- :POWer:ALC:SOURce
- :POWer:ALC:SOURce:EXTernal:COUPling
- :POWer:ALC[:STATe]
- :POWer:ATTenuation
- :POWer:ATTenuation:AUTO
- :POWer:MODE
- :POWer:REFerence
- :POWer:REFerence:STATe
- :POWer:STARt
- :POWer:STOP
- :POWer[:LEVel][:IMMediate]:OFFSet
- :POWer[:LEVel][:IMMediate][:AMPLitude]
- Pulse Modulation Subsystem ([:SOURce])
- SCPI Command Compatibility
- Index
Command Reference
Power Subsystem ([:SOURce])
Chapter 4280
:POWer:ALC:LEVel
Supported All with Option 1E1
[:SOURce]:POWer:ALC:LEVel <value>DB
[:SOURce]:POWer:ALC:LEVel?
This command sets the ALC level when the attenuator hold is active.
*RST
+
1.00000000E
+
000
Range
−
20 to 25
Key Entry
Set ALC Level
Remarks Use this command when the automatic attenuation mode is set to
OFF (0). Refer to “:POWer:ATTenuation:AUTO” on page 283 for
choosing the attenuator mode.
:POWer:ALC:SEARch
Supported All
[:SOURce]:POWer:ALC:SEARch ON|OFF|1|0|ONCE
[:SOURce]:POWer:ALC:SEARch?
This command enables or disables the internal power search calibration.
ON (1) This choice executes the power search automatically with each change in
RF frequency or power.
OFF (0) This choice disables the automatic power search routine.
ONCE This choice executes a single power search of the current RF output signal.
*RST 0
Remarks Use this command when the ALC state is set to OFF (0). Refer to
“:POWer:ALC[:STATe]” on page 282 for setting the ALC state.
If ON was previously selected, executing ONCE will cause OFF to be
the current selection after the power search is completed.
Choices ON OFF 1 0 ONCE
Key Entry
Power Search Manual Auto Do Power Search