User`s guide

SCPI Commands Appendix B
Model N6705 User’s Guide 189
SCPI Command Description
[SOURce:]ARB (continued)
:STAircase
:END
[:LEVel] < NRf+>, (@chanlist)
Sets the end level of the staircase
:TIMe < NRf+>, (@chanlist)
Sets the length of the end time
:NSTeps < NRf+>, (@chanlist)
Sets the number of steps in the staircase
:STARt
[:LEVel] < NRf+>, (@chanlist)
Sets the initial level of the staircase
:TIMe < NRf+>, (@chanlist)
Sets the length of the start time or delay
:TIMe <NRf+>, (@chanlist)
Sets the length of the staircase
:STEP
:END
[:LEVel] < NRf+>, (@chanlist)
Sets the end level of the step
:STARt
[:LEVel] < NRf+>, (@chanlistl)
Sets the initial level of the step
:TIMe < NRf+>, (@chanlist)
Sets the length of the start time or delay
:TRAPezoid
:END
:TIMe < NRf+>, (@chanlist)
Sets the length of the end time
:FTIMe < NRf+>, (@chanlist)
Sets the length of the fall time
:RTIMe < NRf+>, (@chanlist)
Sets the length of the rise time
:STARt
[:LEVel] < NRf+>, (@chanlist)
Sets the initial level of the trapezoid
:TIMe < NRf+>, (@chanlist)
Sets the length of the start time or delay
:TOP
[:LEVel] < NRf+>, (@chanlist)
Sets the top level of the trapezoid
:TIMe < NRf+>, (@chanlist)
Sets the length of the top of the trapezoid
:UDEFined
:BOSTep
[:DATA] <Bool> {,<Bool>}, (@chanlist)
Generate triggers at the Beginning Of STep
:POINts? (@chanlist)
Returns the number of BOST points
:DWELl <NRf> {,<NRf>}, (@chanlist)
Sets the user-defined dwell values
:POINts? (@chanlist)
Returns the number of dwell points
:LEVel <NRf> {,<NRf>}, (@chanlist)
Sets the user-defined level values
:POINts? (@chanlist)
Returns the number of points
:FUNCtion <function>, (@chanlist)
Selects the Arb function (for backward compatibility)
:SHAPe <function>, (@chanlist)
Selects the Arb function (replaces ARB:FUNCtion)
:TYPE CURRent | VOLTage, (@chanlist)
Selects the Arb type (replaces ARB:FUNCtion)
:SEQuence
:COUNt <NRf+> | INFinity, (@chanlist)
Sets the number of times the sequence is repeated
:LENgth? (@chanlist)
Returns the number of steps in the sequence
:QUALity? (@chanlist)
Returns the quality of the waveforms in the sequence
:RESet (@chanlist)
Resets the sequence to its power-on default setting
:STEP
:COUNt <NRf+> | INFinity, <step#>, (@chanlist)
Sets the number of times the sequence step is repeated
:CURRent <ARB_function>, <step#>, (@chanlist)
Programs the waveform steps within a current sequence
:FUNCtion
:SHAPe <function>, <step#>, (@chanlist)
Creates a new sequence step
:PACing DWELl | TRIGger, <step#>, (@chanlist)
Specifies the type of pacing for the step
:VOLTage <ARB_function>, <step#>, (@chanlist)
Programs the waveform steps within a voltage sequence
:TERMinate
:LAST <Bool>, (@chanlist)
Sets the sequence termination mode
:TERMinate:LAST <Bool>, (@chanlist)
Sets the Arb termination mode