Technical data

Notes on USB Electrical Compliance Testing 235
Index
Numerics
100 mA load board schematic, 177
10073C miniature passive probes, 26
1156A probes, 26
500 mA load board schematic, 177
81134A pulse generator, 98
81134A/81130A Instrument Address
configuration option, 66, 98
82357A GPIB-USB converter, 98
82357A USB/GPIB interface, 21
C
cables, 21
calibrate probes, 26
calibration, 26
common ground reference, 26
compensate passive probes, 26
computer, high-speed electrical test bed, 22
configure, 29
connect, 29
D
Data Eye Test Mode configuration option, 175
debug mode, 175
device CHIRP timing, 48
device hi-speed signal quality test, 35
device hi-speed tests, 33
device packet parameters, 41
device receiver sensitivity, 65
device suspend/resume/reset timing, 51
device test J/K, SE0_NAK, 59
differential probe, 25
digital signal generator, 21, 27
driver, USB-OET (OTG Electrical Test)
fixture, 229
droop/drop test, 178
E
E2688A serial data analysis (SDA) and clock
recovery software option, 175
E2697A adapters, 26
E3631A Instrument Address configuration
option, 230
EHCI driver stack, 22
electrical test bed computer, 22
enhanced bandwidth software option, 20, 33,
71, 141
entitlement certificate, 17
equipment required, 20
equipment, setting up, 25
G
ground reference, common, 26
H
high-speed electrical test bed computer, 22
High-Speed Electrical Test Tool Kit software, 22
host CHIRP timing, 159
host controller packet parameters, 148
host disconnect detect, 155
host downstream signal quality test, 200
host hi-speed electrical tests, 141
host hi-speed signal quality, 143
host suspend/resume timing, 164
host test J/K, SE0_NAK, 169
HTML report, 29
hub CHIRP timing - upstream facing port, 117
hub disconnect detect, 86
hub downstream signal quality test, 205
hub hi-speed signal quality test - downstream
facing ports, 78
hub hi-speed signal quality test - upstream
facing ports, 73
hub hi-speed tests, 71
hub jitter test - downstream facing ports, 82
hub packet parameters - upstream facing
port, 90
hub receiver sensitivity - upstream facing
port, 97
hub repeater test - downstream facing
port, 106
hub repeater test - upstream facing port, 111
hub suspend/resume/reset timing - upstream
facing port, 120
hub test J/K, SE0_NAK - downstream facing
port, 134
hub test J/K, SE0_NAK - upstream facing
port, 128
I
identify test environment, 29
in this book, 4
inrush current test, 197
Inrush Current Time Range configuration
option, 176
Inrush Current Trigger Level configuration
option, 176
installing the license key, 17
installing the software, 16
L
license code, 17
license key, installing, 17
load board, 23
M
Marker Placement configuration option, 175
Mask Template configuration option, 176
MATLAB scripts, 175
MATLAB scripts version configuration
option, 176
memory upgrade option, 20, 33, 71, 141
monitor, optional, 25
multimeter, 21
N
N5416A USB 2.0 Compliance Test Option, 3,
20
noise reduction software option, 20, 33, 71,
141
O
On-The-Go electrical tests, 227
optional computer monitor, 25
oscilloscope required, 20
oscilloscope, software, and accessories, 20
P
passive probes, compensating, 26
power supply’s SICL address, 230
probes, calibrating, 26
pulse generator’s SICL address, 66, 98
pulse/pattern generator, 21
R
report, 29
required equipment and software, 20
results, 29
run tests, 29
running tests, 31