Technical data

Index
Service Guide N5230-90025 Index-7
procedure, 7-12
test
, 4-14
troubleshooting, 4-12
kits
calibration, 2-8, 3-6
handle
part numbers
, 6-49
rack mount
part numbers
, 6-49
upgrade
part numbers
, 6-49
verification
, 2-8, 3-6
knob
front panel
illustrated
, 6-9
part number
, 6-8
test
, 4-15
troubleshooting
, 4-12
L
LAN
connector
rear panel, 5-29
cross-over cable
, 4-21
IP address
, 4-19
ping command, 4-19
ping to and from
, 4-19
subnet mask
, 4-19
testing between analyzers, 4-21
troubleshooting
, 4-19
LED board, front panel
illustration, 6-37
part number, 6-36
limiter
illustration, 6-31
part number
, 6-30
removal and replacement, 7-44
linearity
source power
test
, 3-29
test port output power
test
, 3-29
lithium battery
removal and replacement, 7-56
illustrated, 7-57
lithium battery disposal , 1-9
LO power
adjustment, 3-36
load match
cause of failure, 8-11
definition of, 8-11
measurements affected by
, 8-11, 8-12
load, 50-ohm
illustration, 6-21, 6-31
part number, 6-20, 6-30
locating
assembly part numbers, 6-7
hardware part numbers
, 6-7
miscellaneous part numbers
, 6-7
replaceable part numbers
by reference designator
, 6-6
by type of part
, 6-7
M
machine screws
in bottom assemblies
illustration, 6-37
part numbers
, 6-36
in external analyzer
illustration
, 6-41
part numbers
, 6-40
in hard disk drive assembly
part numbers
, 6-44
in rear panel assembly
illustration
, 6-43
part numbers
, 6-42
magnitude check
failure of, 3-16
test port cables
, 3-15
maintenance
cleaning, 2-3
preventive
effect on error terms
, 8-3
MASS 26.5
illustration, 6-16, 6-17, 6-23, 6-27,
6-31
operation
, 5-9, 5-17
part number, 6-16, 6-22, 6-26, 6-30
removal and replacement
, 7-32, 7-34
troubleshooting
, 4-38, 4-39, 4-40
MASSQuad
illustration, 6-16, 6-17, 6-23, 6-27,
6-31
operation
, 5-9, 5-17
part number, 6-16, 6-22, 6-26, 6-30
removal and replacement
, 7-32, 7-34
troubleshooting
, 4-38, 4-39, 4-40
max output power
and frequency range, 5-4
measurement
calibration, 8-3
traceability
, 3-21
path, 3-21
uncertainty
, 3-20
measurement configuration
active
high dynamic range, 5-21
normal
, 5-18
measurement system
troubleshooting, 4-23
measuring
high-dynamic range devices, 2-4
high-power devices
, 2-4
midweb
removal and replacement, 7-53
midweb fans
troubleshooting, 4-11
miscellaneous parts
location of part numbers, 6-7
required for servicing, 2-9
miscellaneous replaceable parts
part numbers, 6-48
mixer brick
illustration, 6-23, 6-27, 6-31
operation, 5-22
part number
, 6-22, 6-26, 6-30
removal and replacement
, 7-36
troubleshooting, 4-41
module
exchange
procedure
, 6-5
motherboard, system
illustration, 6-13, 6-16, 6-17
operation
, 5-27
part number
, 6-12, 6-16
removal and replacement
, 7-22
troubleshooting
, 4-11
motherboard, test set
illustration, 6-23, 6-27, 6-31
part number, 6-22, 6-26, 6-30
multiplier board
illustration, 6-13, 6-16, 6-17
operation
, 5-9
part number, 6-12, 6-16
removal and replacement
, 7-16
troubleshooting
all bands
, 4-33, 4-34, 4-36
multiplier board, second source
illustration, 6-16, 6-17
part number
, 6-16
removal and replacement, 7-20
N
N1966A pulse I/O adapter , 2-6
name plate
front panel
illustrated
, 6-9
part number, 6-8
network analyzer, See analyzer
noise floor, test , 3-32
noise, trace noise test , 3-30
Non-ANSI/NCSL Z540-1-1994
verification, 3-9
O
OCXO (oven-controlled crystal oscillator)
frequency adjustment, 3-35
theory of operation, 5-10
operating environment
specifications, 3-4
verification
, 3-4
operating system