Specifications

23
N2744A T2A Probe Interface Adapter
• Enables Tektronix
®
TekProbe-
BNC
®
level 2 probes to connect
to Agilent’s AutoProbe interface
on InfiniiVision 3000 X-, 4000 X-,
6000 X-, 5000, 6000, and 7000
oscilloscopes
• An easy-to-use plug-on adapter
to the Agilent oscilloscope’s
AutoProbe interface
• Provides necessary probe power,
calibration, and offset control as
needed to the attached TekProbe
probe
The N2744A T2A interface adapter
enables selected TekProbe
®
interface
level 2 probes to be used with
Agilent oscilloscopes with AutoProbe
interface. Existing TekProbe-BNC
probe types can simply be plugged
into the T2A adapter which is then
plugged directly into any AutoProbe
input channel on an InfiniiVision or
Infiniium oscilloscope. Select the
probe model in the scope menu and
the Agilent oscilloscope sets up the
attenuation factor and the probe
type automatically. The T2A interface
adapter supplies the necessary
probe power, calibration (for selected
models only) and offset control as
used by the connected TekProbe
probe. The adapter is targeted for
customers using both Tek active
probes with TekProbe-BNC level 2
interfaces and Agilent oscilloscopes
with the AutoProbe interface.
Tek probe compatibility
The N2744A T2A adapter supports
only the probes listed below with
TekProbe interfaces.
AC/DC current probe
TCP202 50-MHz AC/DC current probe
Single-ended active probes
P6243 Single-ended active probe,
1 GHz, 10:1 without offset
control
P6245 Single-ended active probe,
1.5 GHz, 10:1 with offset
control
P6205 Single-ended active probe,
750 MHz, 10:1 without offset
control
P6241 Single-ended active probe,
4 GHz, 10:1 with offset
control
P6249 Single-ended active probe,
4 GHz, 5:1 with offset control
Differential active probes
P5205
or
P5205A
Differential probe, 100 MHz,
50:1/500:1 with offset control
P5210
or
P5210A
Differential probe, 50 MHz,
100:1/1000:1 with offset
control
P6246 400 MHz, 10:1/1:1 with offset
control
P6247 1 GHz, 10:1/1:1 with offset
control
P6248 1.5 GHz, 10:1/1:1 with offset
control
P6250 500 MHz, 50:1/5:1 with offset
control
P6251 1 GHz, 50:1/5:1 with offset
control
Agilent scope compatibility
• Agilent InfiniiVision 6000 X-Series with
sofware version 6.00 or higher
• Agilent InfiniiVision
3000 X-/4000 X-Series with software
version 1.10 or higher
• Agilent InfiniiVision 5000, 6000, and
7000 Series and future revisions
(except 6000 100-MHz) with software
version 06.16 or higher
Ordering information
N2744A T2A probe interface adapter
Optical-to-Electrical Converters
(works with InfiniiVision 5000, 6000
and 7000 with version 6.16 software
only)
P6701B 1 GHz Optical-to-electrical
converter with FC/PC connector
P6703B 1.2 GHz Optical-to-electrical
converter with FC/PC connector
P6711 250 MHz Optical-to-electrical
converter
P6713 300 MHz Optical-to-electrical
converter