Specifications

30
Specifications
Vertical 92004Q 92504Q 93304Q 95004Q 96204Q
Typical analog bandwidth (3 dB) 20 GHz 25 GHz 33 GHz 50 GHz 63 GHz
Analog bandwidth (3 dB)* 20 GHz 25 GHz 32 GHz 50 GHz 62 GHz
2 channel sample rate 80 80 80 160 160
4 channel sample rate 80 80 80 80 80
Rise time/fall time 92004Q 92504Q 93304Q 95004Q 96204Q
10 - 90%
4
22.5 ps 18 ps 13 ps 9 ps 7 ps
20 - 80% 17.5 ps 14 ps 10.6 ps 7 ps 5 ps
Input impedance
3
50 , +/- 3%
Sensitivity
2
1 mV/div to 1 V/div
Input coupling DC
Vertical resolution
1
8 bits, ≥ 12 bits with averaging
Channel to channel isolation (any two
channels with equal V/div settings)
DC to 3 GHz: 60dB (≥ 1000:1)
3 GHz to 8 GHz: 40 dB (≥ 100:1)
8 GHz to BW: 35dB (≥ 56:1)
DC gain accuracy* ± 2% of full scale at full resolution channel scale
(± 2.5% for 5mV/div)
Maximum input voltage ± 5V for steady state and transient measurements
Offset range Vertical sensitivity
0 mV/div to ≥ 40 mV/div
> 40 mV/div to ≥ 75 mV/div
> 75 mV/div to ≥ 130 mV/div
> 130 mV/div to ≥ 240 mV/div
> 240 mV/div
Available offset
± 0.4V
± 0.9V
± 1.6V
± 3.0V
± 4.0V
Offset accuracy* ≤ 3.5V: ± (2% of channel offset + 1% of full scale) + 1 mV
> 3.5V: ± (2% of channel offset + 1% of full scale)
Dynamic range ± 4 div from center screen
DC voltage measurement accuracy Dual cursor: ± [(DC gain accuracy) + (resolution)]
Single Cursor: ± [(DC gain accuracy) + (offset accuracy) + (resolution/2)]
RMS noise floor (scope only)
Volts / div 92004Q 92504Q 93304Q 95004Q 96204Q
10 mV 0.41 mV(rms) 0.48 mV(rms) 0.60 mV(rms) 0.90 mV(rms) 1.0 mV(rms)
50 mV 1.46 mV(rms) 1.7 mV(rms) 2.00 mV(rms) 2.90 mV(rms) 3.3 mV(rms)
100 mV 2.90 mV(rms) 3.3 mV(rms) 3.90 mV(rms) 5.70 mV(rms) 6.4 mV(rms)
1 V 28.6 mV(rms) 32.5 mV(rms) 38.1 mV(rms) 56.7 mV(rms) 63 mV(rms)
*Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm up period, and ± 5° C from annual calibration temperature
1. Vertical resolution for 8 bits = 0.4% of full scale, for 12 bits = 0.024% of full scale
2. Full scale is defined as 8 vertical divisions. Magnification is used below 7.5 mV/div. Below 7.5 mV/div, full-scale is defined as 60 mV/div. The major scale settings are
5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, and 1V.
3. Input impedance is valid when V/div scaling is adjusted to show all waveform vertical values within scope display.
4. Rise time calculated by using 0.45/BW for (10-90%) rise time