Technical data

930 Agilent InfiniiVision 6000 Series Oscilloscopes Programmer's Guide
Index
SPI trigger frame, 601
SPI triggering, 481
square root math function, 285
SRE (Service Request Enable Register), 145,
771
SRQ (Service Request interrupt), 164, 171, 175
STANdard commands, 688
standard deviation measured on
waveform, 347
Standard Event Status Enable Register
(ESE), 130, 776
Standard Event Status Register (ESR), 132, 775
standard for video, 607
standard, LIN, 575
start acquisition, 148, 162, 186, 188
start and stop edges, 329
STARt commands, 688
start cursor, 731
start measurement, 324
start print job, 303
start time, 536, 731
start time marker, 728
state memory, 143
state of instrument, 135, 464
STATistics commands, 689
statistics increment, 352
statistics reset, 353
statistics results, 343
statistics, type of, 351
status
, 146, 189, 191
Status Byte Register (STB), 144, 146, 147, 769
STATus commands, 689
status data structure clear, 129
status registers, 68
status reporting, 763
STB (Status Byte Register), 144, 146, 147, 769
step size for frequency span, 291
stop, 162, 190
stop acquisition, 190
STOP commands, 689
stop cursor, 732
stop displaying channel, 160
stop displaying math function, 160
stop displaying pod, 160
stop on mask test failure, 393
stop time, 536, 732
storage, 143
store instrument setup, 135, 143
store setup, 143
store waveforms to pixel memory, 170
storing calibration information, 222
string variables, 66
string variables, reading multiple query results
into, 67
string variables, reading query results into
multiple, 67
string, quoted ASCII
, 121
subnet mask, 49
subsource, waveform source, 654
subsystem commands, 124, 818
subtract math function, 278, 285, 650
subtract math function as g(t) source, 281
sweep mode, trigger, 479, 489
sweep speed set to fast to measure fall
time, 334
sweep speed set to fast to measure rise
time, 346
switch disable, 461
switch, calibration protect, 226
sync break, LIN, 576
sync frame count (FlexRay), 442
syntax elements, 120
syntax rules, program data, 802
syntax, optional terms, 120
syntax, program message, 799
SYSTem commands, 457
system commands, 458, 459, 460, 461, 464,
466
system commands introduction, 457
T
tdelta, 727
tedge, 354
telnet ports 5024 and 5025, 638
Telnet sockets, 69
temporary message, 459
TER (Trigger Event Register), 191, 772
termination conditions, mask test, 389
test sigma, mask test run, 394
test, self, 149
text, writing to display, 459
threshold, 255, 407, 707, 753
THReshold commands, 690
threshold voltage (lower) for
measurement, 725
threshold voltage (upper) for
measurement, 735
thresholds, 329, 728
thresholds used to measure period, 339
thresholds, how autoscale affects, 156
TIFF image format, 421
time base, 469, 470, 471, 473, 474, 749
time base commands introduction, 468
time base reset conditions, 140
time base window, 476, 477, 478
time between points, 727
time buckets, 196, 197
TIME commands, 690
time delay, 749
time delta, 727
time difference between data points, 658
time duration, 502, 503, 506, 536
time holdoff for trigger, 484
time interval, 354, 356, 727
time interval between trigger and
occurrence, 733
time marker sets start time, 728
time per division, 471
time record, 292
time specified, 366
time, calibration, 228
time, mask test run, 395
time, start marker, 731
time, stop marker, 732
time, system, 466
time/div, how autoscale affects, 156
time-at-max measurement, 729
time-at-min measurement, 730
TIMebase commands, 467
timebase vernier, 475
TIMebase:MODE, 64
time-ordered label list, 262
timeout, 595
timer, 591
timing measurement, 324
title channels, 237
title, mask test, 403
tolerance, automask, 378
, 379
top of waveform value measured, 367
TOTal commands, 690
total frame count (CAN), 437
total frame count (FlexRay), 443
total waveforms in mask test, 383
trace memories, how autoscale affects, 156
trace memory, 189, 192
trace memory data, 259
track measurements, 348
trademarks, 2
transfer instrument state, 135, 464
transmit, 259
transmit word size, I2S, 554
tree traversal rules, 818
tree, command, 803
TRG (Trigger), 145, 147, 148
TRIG OUT BNC, 223
trigger (external) input impedance, 269, 714
trigger armed event register, 177, 179
trigger burst, UART, 613
TRIGger CAN commands, 490
trigger channel source, 537, 606
TRIGger commands, 479, 690
TRIGger commands, general, 482
trigger data, UART, 614
trigger duration, 502, 503
TRIGger DURation commands, 501
TRIGger EBURst commands, 507
trigger edge, 587
TRIGger EDGE commands, 511
trigger edge coupling, 512
trigger edge slope, 515
trigger event bit, 191
Trigger Event Register (TER), 772
TRIGger FLEXray commands, 517
TRIGger GLITch commands, 529
trigger holdoff, 484
TRIGger I2S commands, 538
trigger idle, UART, 615
TRIGger IIC commands, 556
trigger level constants, 239
trigger level voltage, 513
TRIGger LIN commands, 565
TRIGger M1553 commands, 578
trigger occurred, 147
trigger pattern, 487, 504
trigger qualifier, 505