Technical data

Index
Agilent InfiniiVision 6000 Series Oscilloscopes Programmer's Guide 929
report transition, 354, 356
reporting status, 763
reporting the setup, 481
request service, 147
Request-for-OPC flag clear, 129
reset, 140, 590
RESet commands, 684
reset conditions, 140
reset mask statistics, 381
reset measurements, 161, 258
resolution of printed copy, 722
resource session object, 61
ResourceManager object, 61
restore configurations, 135, 139, 143, 464
restore labels, 261
restore setup, 139
return values, query, 820
returning acquisition type, 208
returning number of data points, 200
right reference, 473
rise time measurement, 324
rise time of positive edge, 346
rising edge, 487, 587
RMODe commands, 684
RMS value measurement, 365
roll time base mode, 469
root (:) commands, 151, 153
root level commands, 124
RQL (Request Control) status bit
, 131, 133
RQS (Request Service), 147
RS-232/UART triggering, 481
RST (Reset), 140
rules, tree traversal, 818
rules, truncation, 800
RUMode commands, 684
run, 148, 186
Run bit, 177, 179
run mode, mask test, 389
running configuration, 143, 464
Rx frame count (UART), 454
Rx source, 619
S
sample rate, 207
sampled data, 711
sampled data points, 638
SAMPlepoint commands, 685
SAV (Save), 143
save, 143, 416
SAVE commands, 415, 685
save filename, 417
save image, 418
save image with inksaver, 422
save mask, 424, 425
save mask test failures, 392
save path information, 426
save setup, 427
SAVE TO INTERN, 170
save waveform data, 428
save waveforms to pixel memory, 170
saved image, area, 419
saving and recalling data, 256
SBUS commands, 432
scale, 288, 474, 478
SCALe commands, 686
scale factors output on hardcopy, 297, 420
scale for channels, 246
scale units for channels, 247
scale units for external trigger, 275
scaling display factors, 239
SCPI commands, 69
scratch measurements, 726
screen area for hardcopy print, 295
screen area for saved image, 419
screen data, 259
SECAM, 603, 607
seconds per division, 474
SEGMented commands, 686
segmented waveform save option, 431
segments, analyze, 202
segments, count of waveform, 648
segments, setting number of memory, 203
segments, setting the index, 204
segments, time tag, 649
select measurement channel, 349
self-test, 149
sensing a channel probe, 710
sensing a external trigger probe, 715
sensitivity of oscilloscope input, 239
sequence, 588, 589, 590
sequence trigger, 592
SEQuence trigger commands, 585
sequence triggering, 481
sequencer edge counter, 586
sequencer timer, 591
sequential commands, 821
serial clock, 560, 599
serial data, 561, 600
serial decode bus, 433
serial decode bus display, 439
serial decode mode, 448
serial frame, 601
serial number, 187
service request, 147
Service Request Enable Register (SRE), 145,
771
set, 140
set center frequency, 279
set conditions, 156
set cursors, 731, 732
set date, 458
set delay, 156
set thresholds, 156
set time, 466
set time/div, 156
set up oscilloscope, 49
setting digital display, 251
setting digital label, 217, 252
setting digital position, 253
setting digital threshold, 255
setting display, 280
setting external trigger level, 266
setting impedance for channels, 235
setting inversion for channels, 236
setting pod display, 405
setting pod size, 406
setting pod threshold, 407
settings, 139, 143
settings, instrument, 294
setup, 194, 211, 231, 249, 256, 278,
294, 464
SETup commands, 686
setup configuration, 139, 143, 464
setup defaults, 140
setup memory, 139
setup reported, 481
setup, recall, 414
setup, save, 427
short form, 4, 800
show channel labels, 261
show measurements, 324, 348
SICL example in C, 903
SICL example in Visual Basic, 912
SICL examples, 903
sigma, mask test run, 394
SIGNal commands, 687
signal type, 243, 272
signed data, 634
simple command headers, 801
single acquisition, 188
single-ended probe heads, 240
single-ended signal type, 243, 272
single-shot DUT, synchronizing with, 792
size, 254, 406
SIZE commands, 687
skew, 242, 708
slope, 515, 594
slope (direction) of waveform
, 733
SLOPe commands, 687
slope not valid in TV trigger mode, 515
slope of edge, 587
slope parameter for delay measurement, 331
slope, Nth edge in burst, 510
smoothing acquisition type, 632
software version, 134
source, 264, 278, 349, 498, 574, 650
SOURce commands, 687
source for function, 289, 290, 716
source for trigger, 516
source for TV trigger, 606
source, automask, 376
source, FLEXray, 527
source, mask test, 402
SOURce1 commands, 688
SOURce2 commands, 688
span, 278
span of frequency on display, 291
specify measurement, 349
SPI, 594, 595, 597
SPI commands, 688
SPI decode bit order, 449
SPI decode word width, 450
SPI trigger, 596, 598
SPI trigger clock, 599
SPI trigger commands, 593
SPI trigger data, 600