Technical data

928 Agilent InfiniiVision 6000 Series Oscilloscopes Programmer's Guide
Index
pattern data, LIN, 568
pattern duration, 502, 503, 531, 532
pattern format, I2S, 545
pattern format, LIN, 571
pattern length, 493, 570
pattern trigger, 487
pattern triggering, 480
pattern width, 598
peak data, 632
peak detect, 208
peak detect acquisition type, 194, 632
peaks, 278
peak-to-peak vertical value measurement, 363
pending operations, 136
percent of waveform overshoot, 337
percent thresholds, 329
period measured to calculate phase, 340
period measurement, 59, 324, 339
persistence, waveform, 256, 263
phase measured between channels, 340
phase measurements, 354
pixel memory, 264
pixel memory, saving display to, 170
PLL Locked bit, 166, 177
pod, 404, 405, 406, 407
, 650, 707
POD commands, 404
POD data format, 635
pod, stop displaying, 160
points, 200, 641, 643
POINts commands, 682
points in waveform data, 631
polarity, 605, 617
POLarity commands, 682
polarity for glitch trigger, 534
polling synchronization with timeout, 790
polling wait, 788
PON (Power On) status bit, 131, 133
portrait layout for hardcopy, 300
position, 253, 312, 470, 476
POSition commands, 682
position cursors, 731, 732
position in zoomed view, 476
position waveforms, 712
positive glitch trigger polarity, 534
positive pulse width, 342
positive pulse width measurement, 59
positive slope, 515, 594
positive slope, Nth edge in burst, 510
positive TV trigger polarity, 605
positive width, 342
preamble data, 645
preamble metadata, 630
precision analysis, 462
precision analysis record, 643
predefined logic threshold, 707
predefined threshold voltages, 753
present working directory, recall
operations, 413
present working directory, save operations, 426
preset conditions, 140
preshoot measured on waveform, 341
previously stored configuration, 139
print command, 185
print job, start, 303
print mask test failures, 391
print query, 747
printer, 719
printer driver for hardcopy, 724
printer hardcopy format, 721
printer, active, 296
printing, 294
printing in grayscale, 722
probe, 513
probe attenuation affects channel voltage
range, 245
probe attenuation factor (external trigger), 270
probe attenuation factor for selected
channel, 239
PROBe commands, 683
probe head type, 240
probe ID, 241, 271
probe sense for oscilloscope, 710, 715
probe skew value, 242, 708
process sigma, mask test run, 394
program data,
800
program data syntax rules, 802
program initialization, 58
program message, 61, 128
program message syntax, 799
program message terminator, 800
program structure, 58
programming examples, 4, 823
protecting against calibration, 226
protection, 181, 183, 244, 273
PROTection commands, 683
protection lock, 463
pulse width, 336, 342
pulse width duration trigger, 531, 532, 536
pulse width measurement, 59, 324
pulse width trigger, 486
pulse width trigger level, 533
pulse width triggering, 480
PWD commands, 683
pwidth, 342
Q
qualifier, 536
QUALifier commands, 683
qualifier, trigger duration, 502, 503, 505
queries, multiple, 67
query error detected in Standard Event
Status, 133
query responses, block data, 66
query responses, reading, 65
query results, reading into numeric
variables, 66
query results, reading into string variables, 66
query return values, 820
query setup, 294, 308, 324, 464
query subsystem, 211, 249, 278
querying setup, 231
querying the subsystem, 481
queues, clearing, 785
quick reference, commands, 71
quoted ASCII string, 121
QYE (Query Error) status bit, 131, 133
R
range, 278, 477
RANGe commands, 683
range for channels, 245
range for duration trigger, 506
range for external trigger, 274
range for full-scale vertical axis, 286
range for glitch trigger, 536
range for time base, 471
range of offset values, 238
range qualifier, 535
range, I2S, 546
ranges, value, 121
rate, 207
ratio of AC RMS values measured between
channels, 364
raw acquisition record, 643
RCL (Recall), 139
read configuration, 135
read trace memory, 259
ReadIEEEBlock method, 61, 65, 67
ReadList method, 61, 65
ReadNumber method, 61, 65
readout, 727
ReadString method, 61, 65
real-time acquisition mode, 194, 199
recall, 139, 409, 464
RECall commands, 409
recall filename, 410
recall image
, 411
recall mask, 412
recall path information, 413
recall setup, 414
recalling and saving data, 256
receiver width, I2S, 548
RECTangular window for transient signals, 292
reference, 278, 473
reference clock, 472
REFerence commands, 684
reference for time base, 749
reference signal (10 MHz), 201
reference signal mode, 472
registers, 132, 139, 143, 155, 164, 166, 168,
171, 173, 175, 177, 179, 181, 183
registers, clearing, 785
reject filter, 514
reject high frequency, 483
reject noise, 486
remote control examples, 823
Remote Terminal Address (RTA), M1553
trigger, 581
remove cursor information, 309
remove labels, 261
remove message from display, 459
reorder channels,
156
repetitive acquisitions, 186
report errors, 460