Technical data

922 Agilent InfiniiVision 6000 Series Oscilloscopes Programmer's Guide
Index
BYTeorder, 636
C
C, SICL library example, 903
C, VISA library example, 857
C#, VISA COM example, 834
C#, VISA example, 876
CAL PROTECT switch, 219, 226
calculating preshoot of waveform, 341
calculating the waveform overshoot, 337
calibrate, 221, 222, 226, 228
CALibrate commands, 219
calibrate date, 221
calibrate introduction, 219
calibrate label, 222
calibrate output, 223
calibrate start, 224
calibrate status, 225
calibrate switch, 226
calibrate temperature, 227
calibrate time, 228
CAN, 492
CAN acknowledge, 496, 750
CAN baud rate, 497
CAN commands, 668
CAN frame counters, reset, 436
CAN id pattern, 494
CAN signal definition, 751
CAN source, 498
CAN trigger, 493, 499
CAN trigger commands, 490
CAN trigger pattern id mode, 495
CAN triggering,
480
capture data, 162
capturing data, 58
CDISplay, 161
center frequency set, 278, 279
center of screen, 663
center reference, 473
center screen, vertical value at, 284, 287
channel, 192, 237, 705, 707
channel coupling, 233
channel display, 234
channel input impedance, 235
channel inversion, 236
channel label, 237, 706
channel labels, 261, 262
channel numbers, 712
channel overload, 244
channel probe ID, 271
channel protection, 244
channel reset conditions, 140
channel selected to produce trigger, 537, 606
channel signal type, 243
channel skew for oscilloscope probe, 242, 708
channel status, 189, 712
channel threshold, 707
channel vernier, 248
channel, stop displaying, 160
CHANnel<n> commands,
229, 230
channels to autoscale, 159
channels, how autoscale affects, 156
characters to display, 459
classes of input signals, 292
classifications, command, 798
clear, 258
clear bus command, 215
CLEar commands, 669
clear cumulative edge variables, 705
clear display, 161
clear markers, 326, 726
clear measurement, 326, 726
clear message queue, 129
Clear method, 61
clear screen, 713
clear status, 129
clear waveform area, 256
clipped high waveform data value, 638
clipped low waveform data value, 638
clock, 560, 594, 595, 599
CLOCk commands, 669
clock slope, I2S, 542
CLOCk source, I2S, 549
CLS (Clear Status), 129
CME (Command Error) status bit, 131, 133
CMOS threshold voltage for digital
channels, 255, 707
CMOS trigger threshold voltage, 753
code, :ACQuire:COMPlete
, 196
code, :ACQuire:SEGMented, 204
code, :ACQuire:TYPE, 209
code, :AUToscale, 157
code, :CHANnel<n>:LABel, 237
code, :CHANnel<n>:PROBe, 239
code, :CHANnel<n>:RANGe, 245
code, :DIGitize, 162
code, :DISPlay:DATA, 260
code, :DISPlay:LABel, 261
code, :DISPlay:ORDer, 712
code, :MEASure:PERiod, 350
code, :MEASure:RESults, 343
code, :MEASure:TEDGe, 355
code, :MTESt, 372
code, :POD<n>:THReshold, 407
code, :RUN/:STOP, 186
code, :SYSTem:SETup, 464
code, :TIMebase:DELay, 749
code, :TIMebase:MODE, 469
code, :TIMebase:RANGe, 471
code, :TIMebase:REFerence, 473
code, :TRIGger:MODE, 485
code, :TRIGger:SLOPe, 515
code, :TRIGger:SOURce, 516
code, :VIEW and :BLANk, 192
code, :WAVeform, 651
code, :WAVeform:DATA, 638
code, :WAVeform:POINts, 642
code, :WAVeform:PREamble, 646
code, :WAVeform:SEGMented, 204
code, *RST, 142
code, SICL library example in C, 903
code, SICL library example in Visual Basic, 912
code, VISA COM library example in C#, 834
code, VISA COM library example in Visual
Basic, 824
code, VISA COM library example in Visual Basic
.NET, 846
code, VISA library example in C, 857
code, VISA library example in C#, 876
code, VISA library example in Visual Basic, 866
code, VISA library example in Visual Basic
.NET, 889
colon, root commands prefixed by, 153
color palette for hardcopy, 301
color palette for image, 423
Comma Separated Values (CSV) hardcopy
format, 721
Comma Separated Values (CSV) waveform data
format, 429
command classifications, 798
command differences from 54620/54640 series
oscilloscopes, 43
command errors detected in Standard Event
Status, 133
command header, 800
command headers, common, 802
command headers, compound, 801
command headers, simple, 801
command strings, valid, 799
command tree, 803
commands by subsystem, 123
commands in alphabetical order, 665
commands quick reference, 71
commands sent over interface, 128
commands, more about, 797
commands, obsolete and discontinued, 699
common (*) commands, 124, 125, 128
common command headers, 802
completion criteria for an acquisition, 196
, 197
compound command headers, 801
compound header, 818
computer control examples, 823
conditions for external trigger, 266
conditions, reset, 140
configurations, oscilloscope, 135, 139, 143,
464
Configure softkey, 50
connect oscilloscope, 49
connect sampled data points, 711
constants for making automatic
measurements, 239
constants for scaling display factors, 239
constants for setting trigger levels, 239
Control softkey, 49, 50
controller initialization, 58
copy display, 185
core commands, 798
count, 586, 637
COUNt commands, 669
count values, 197
count, Nth edge of burst, 508
counter, 327
coupling, 512
COUPling commands, 670
coupling for channels, 233