Technical data

882 Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
Index
TER (Trigger Event Register), 175, 724
termination conditions, mask test, 356
test sigma, mask test run, 361
test, self, 134
text, writing to display, 421
threshold voltage (lower) for
measurement, 679
threshold voltage (upper) for
measurement, 689
thresholds, 295, 682
thresholds used to measure period, 305
thresholds, how autoscale affects, 140
TIFF image format, 383
time base, 431, 432, 433, 434, 435, 703
time base commands introduction, 429
time base reset conditions, 125
time base window, 437, 438, 439
time between points, 681
time buckets, 180, 181
TIME commands, 648
time delay, 703
time delta, 681
time difference between data points, 619
time duration, 465, 466, 469, 498
time holdoff for trigger, 445
time interval, 320
, 322, 681
time interval between trigger and
occurrence, 687
time marker sets start time, 682
time per division, 433
time record, 259
time specified, 332
time, calibration, 202
time, mask test run, 362
time, start marker, 685
time, stop marker, 686
time, system, 428
time/div, how autoscale affects, 140
time-at-max measurement, 683
time-at-min measurement, 684
TIMebase commands, 429
timebase vernier, 436
TIMebase:MODE, 54
time-ordered label list, 229
timeout, 557
timer, 553
timing measurement, 290
title channels, 211
title, mask test, 370
tolerance, automask, 345, 346
top of waveform value measured, 333
total frame count (CAN), 399
total frame count (FlexRay), 405
total waveforms in mask test, 350
trace memories, how autoscale affects, 140
trace memory, 173, 176
trace memory data, 226
track measurements
, 314
trademarks, 2
transfer instrument state, 121, 426
transmit, 226
transmit word size, I2S, 516
tree traversal rules, 769
tree, command, 755
TRG (Trigger), 130, 132, 133
TRIG OUT BNC, 197
trigger (external) input impedance, 236, 668
trigger armed event register, 161, 163
trigger burst, UART, 575
TRIGger CAN commands, 452
trigger channel source, 499, 568
TRIGger commands, 440, 649
TRIGger commands, general, 443
trigger data, UART, 576
trigger duration, 465, 466
TRIGger DURation commands, 464
TRIGger EBURst commands, 470
trigger edge, 549
TRIGger EDGE commands, 474
trigger edge coupling, 475
trigger edge slope, 478
trigger event bit, 175
Trigger Event Register (TER), 724
TRIGger FLEXray commands, 480
TRIGger GLITch commands, 492
trigger holdoff,
445
TRIGger I2S commands, 500
trigger idle, UART, 577
TRIGger IIC commands, 518
trigger level constants, 213
trigger level voltage, 476
trigger level, 50%, 446
TRIGger LIN commands, 527
TRIGger M1553 commands, 540
trigger occurred, 132
trigger pattern, 449, 467
trigger qualifier, 468
trigger qualifier, UART, 580
trigger reset conditions, 125
TRIGger SEQuence commands, 547
trigger SPI clock slope, 556
TRIGger SPI commands, 555
trigger status bit, 175
trigger sweep mode, 440
TRIGger TV commands, 564
trigger type, UART, 583
TRIGger UART commands, 570
TRIGger USB commands, 585
trigger, CAN, 462
trigger, CAN acknowledge, 704
trigger, CAN pattern data, 454
trigger, CAN pattern data length, 455
trigger, CAN pattern ID, 456
trigger, CAN pattern ID mode, 457
trigger, CAN sample point, 458
trigger, CAN signal baudrate, 459
trigger, CAN signal definition, 460
trigger, CAN source, 461
trigger, duration greater than, 465
trigger, duration less than, 466
trigger, duration pattern, 467
trigger, duration qualifier, 468
trigger, duration range, 469
trigger, edge coupling, 475
trigger, edge level, 476
trigger, edge reject, 477
trigger, edge slope, 478
trigger, edge source, 479
trigger, FLEXray, 491
trigger, FLEXray autosetup, 481
trigger, FLEXray error, 484
trigger, FLEXray event, 485
trigger, FLEXray source, 490
trigger, glitch greater than, 493
trigger, glitch less than, 494
trigger, glitch level, 495
trigger, glitch polarity, 496
trigger, glitch qualifier, 497
trigger, glitch range, 498
trigger, glitch source, 499
trigger, high frequency reject filter, 444
trigger, holdoff, 445
trigger, I2S, 514
trigger, I2S alignment, 502
trigger, I2S audio channel, 503
trigger, I2S clock slope, 504
trigger, I2S CLOCksource, 511
trigger, I2S DATA source, 512
trigger, I2S pattern data, 505
trigger, I2S pattern format, 507
trigger, I2S range, 508
trigger, I2S receiver width,
510
trigger, I2S transmit word size, 516
trigger, I2S word select (WS) low, 517
trigger, I2S word select (WS) source, 513
trigger, IIC clock source, 522
trigger, IIC data source, 523
trigger, IIC pattern address, 519
trigger, IIC pattern data, 520
trigger, IIC pattern data 2, 521
trigger, IIC qualifier, 524
trigger, IIC signal baudrate, 535
trigger, IIC type, 525
trigger, LIN, 539
trigger, LIN pattern data, 530
trigger, LIN pattern data length, 532
trigger, LIN pattern format, 533
trigger, LIN sample point, 534
trigger, LIN signal definition, 705
trigger, LIN source, 536
trigger, mode, 447
trigger, noise reject filter, 448
trigger, Nth edge in burst slope, 473
trigger, Nth edge of burst count, 471
trigger, pattern, 449
trigger, sequence, 554
trigger, sequence count, 548
trigger, sequence edge, 549
trigger, sequence find, 550
trigger, sequence pattern, 551
trigger, sequence reset, 552
trigger, sequence timer, 553
trigger, SPI clock slope, 556
trigger, SPI clock source, 561
trigger, SPI clock timeout
, 557
trigger, SPI data source, 562