Technical data
Index
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide 881
SEGMented commands, 645
segmented waveform save option, 393
segments, analyze, 185
segments, count of waveform, 609
segments, setting number of memory, 186
segments, setting the index, 187
segments, time tag, 610
select measurement channel, 315
self-test, 134
sensing a channel probe, 665
sensing a external trigger probe, 669
sensitivity of oscilloscope input, 213
sequence, 550, 551, 552
sequence trigger, 554
SEQuence trigger commands, 547
sequence triggering, 442
sequencer edge counter, 548
sequencer timer, 553
sequential commands, 773
serial clock, 522, 561
serial data, 523, 562
serial decode bus, 395
serial decode bus display, 401
serial decode mode, 410
serial frame, 563
serial number, 171
service request, 132
Service Request Enable Register (SRE), 130,
723
set, 125
set center frequency,
246
set conditions, 140
set cursors, 685, 686
set date, 420
set delay, 140
set thresholds, 140
set time, 428
set time/div, 140
set up oscilloscope, 39
setting display, 247
setting external trigger level, 233
setting impedance for channels, 209
setting inversion for channels, 210
settings, 124, 128
settings, instrument, 261
setup, 178, 205, 223, 245, 261, 426
SETup commands, 645
setup configuration, 124, 128, 426
setup defaults, 125
setup memory, 124
setup reported, 442
setup, recall, 376
setup, save, 389
short form, 3, 752
show channel labels, 228
show measurements, 290, 314
SICL example in C, 855
SICL example in Visual Basic, 864
SICL examples, 855
sigma, mask test run, 361
SIGNal commands, 645
signal type, 217, 239
signed data, 595
simple command headers, 753
single acquisition, 172
single-ended probe heads, 214
single-ended signal type, 217, 239
single-shot DUT, synchronizing with, 744
skew, 216, 663
slope, 478, 556
slope (direction) of waveform, 687
SLOPe commands, 646
slope not valid in TV trigger mode, 478
slope of edge, 549
slope parameter for delay measurement, 297
slope, Nth edge in burst, 473
smoothing acquisition type, 594
software version, 120
source, 231, 245, 315, 461, 536, 611
SOURce commands, 646
source for function, 256, 257, 670
source for trigger, 479
source for TV trigger,
568
source, automask, 343
source, FLEXray, 490
source, mask test, 369
SOURce1 commands, 647
SOURce2 commands, 647
span, 245
span of frequency on display, 258
specify measurement, 315
SPI, 556, 557, 559
SPI commands, 647
SPI decode bit order, 411
SPI decode word width, 412
SPI trigger, 558, 560
SPI trigger clock, 561
SPI trigger commands, 555
SPI trigger data, 562
SPI trigger frame, 563
SPI triggering, 442
square root math function, 252
SRE (Service Request Enable Register), 130,
723
SRQ (Service Request interrupt), 148, 155, 159
STANdard commands, 647
standard deviation measured on
waveform, 313
Standard Event Status Enable Register
(ESE), 116, 728
Standard Event Status Register (ESR), 118, 727
standard for video, 569
standard, LIN, 537
start acquisition
, 133, 146, 170, 172
start and stop edges, 295
STARt commands, 647
start cursor, 685
start measurement, 290
start print job, 270
start time, 498, 685
start time marker, 682
state memory, 128
state of instrument, 121, 426
STATistics commands, 647
statistics increment, 318
statistics reset, 319
statistics results, 309
statistics, type of, 317
status, 131, 173, 175
Status Byte Register (STB), 129, 131, 132, 721
STATus commands, 647
status data structure clear, 115
status registers, 58
status reporting, 715
STB (Status Byte Register), 129, 131, 132, 721
step size for frequency span, 258
stop, 146, 174
stop acquisition,
174
STOP commands, 648
stop cursor, 686
stop displaying channel, 144
stop displaying math function, 144
stop displaying pod, 144
stop on mask test failure, 360
stop time, 498, 686
storage, 128
store instrument setup, 121, 128
store setup, 128
store waveforms to pixel memory, 154
storing calibration information, 196
string variables, 56
string variables, reading multiple query results
into, 57
string variables, reading query results into
multiple, 57
string, quoted ASCII, 107
subnet mask, 39
subsource, waveform source, 615
subsystem commands, 110, 769
subtract math function, 245, 252, 611
subtract math function as g(t) source, 248
sweep mode, trigger, 440, 451
sweep speed set to fast to measure fall
time, 300
sweep speed set to fast to measure rise
time, 312
switch disable, 423
switch, calibration protect, 200
sync break, LIN, 538
sync frame count (FlexRay), 404
syntax elements, 106
syntax rules, program data, 754
syntax, optional terms, 106
syntax, program message, 751
SYSTem commands, 419
system commands, 420, 421, 422, 423, 426,
428
system commands introduction, 419
T
tdelta, 681
tedge, 320
telnet ports 5024 and 5025, 599
Teln et sockets, 59
temporary message, 421