Technical data

880 Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
Index
probe attenuation factor for selected
channel, 213
PROBe commands, 641
probe head type, 214
probe ID, 215, 238
probe sense for oscilloscope, 665, 669
probe skew value, 216, 663
process sigma, mask test run, 361
program data, 752
program data syntax rules, 754
program initialization, 48
program message, 51, 113
program message syntax, 751
program message terminator, 752
program structure, 48
programming examples, 4, 775
protecting against calibration, 200
protection, 165, 167, 218, 240
PROTection commands, 642
protection lock, 425
pulse width, 302, 308
pulse width duration trigger, 493, 494, 498
pulse width measurement, 49, 290
pulse width trigger, 448
pulse width trigger level, 495
pulse width triggering, 441
PWD commands
, 642
pwidth, 308
Q
qualifier, 498
QUALifier commands, 642
qualifier, trigger duration, 465, 466, 468
queries, multiple, 57
query error detected in Standard Event
Status, 119
query responses, block data, 56
query responses, reading, 55
query results, reading into numeric
variables, 56
query results, reading into string variables, 56
query return values, 772
query setup, 261, 275, 290, 426
query subsystem, 245
querying setup, 205
querying the subsystem, 442
queues, clearing, 737
quick reference, commands, 61
quoted ASCII string, 107
QYE (Query Error) status bit, 117, 119
R
range, 245, 438
RANGe commands, 642
range for channels, 219
range for duration trigger, 469
range for external trigger, 241
range for full-scale vertical axis, 253
range for glitch trigger, 498
range for time base, 433
range of offset values, 212
range qualifier, 497
range, I2S, 508
ranges, value, 107
rate, 190
ratio of AC RMS values measured between
channels, 330
raw acquisition record, 604
RCL (Recall), 124
read configuration, 121
read trace memory, 226
ReadIEEEBlock method, 51, 55, 57
ReadList method, 51, 55
ReadNumber method, 51, 55
readout, 681
ReadString method, 51, 55
real-time acquisition mode, 178, 183
recall, 124, 371, 426
RECall commands, 371
recall filename, 372
recall image, 373
recall mask, 374
recall path information, 375
recall setup, 376
recalling and saving data, 223
receiver width, I2S, 510
RECTangular window for transient signals, 259
reference, 245, 434
REFerence commands, 642
reference for time base, 703
registers, 118, 124, 128, 139, 148, 150, 152,
155, 157, 159, 161, 163, 165, 167
registers, clearing, 737
reject filter, 477
reject high frequency, 444
reject noise, 448
remote control examples, 775
Remote Terminal Address (RTA), M1553
trigger, 543
remove cursor information, 276
remove labels, 228
remove message from display, 421
reorder channels, 140
repetitive acquisitions, 170
report errors, 422
report transition
, 320, 322
reporting status, 715
reporting the setup, 442
request service, 132
Request-for-OPC flag clear, 115
reset, 125, 552
RESet commands, 643
reset conditions, 125
reset mask statistics, 348
reset measurements, 145, 225
resolution of printed copy, 676
resource session object, 51
ResourceManager object, 51
restore configurations, 121, 124, 128, 426
restore labels, 228
restore setup, 124
return values, query, 772
returning acquisition type, 191
returning number of data points, 184
right reference, 434
rise time measurement, 290
rise time of positive edge, 312
rising edge, 449, 549
RMODe commands, 643
RMS value measurement, 331
roll time base mode, 431
root (:) commands, 136, 138
root level commands, 110
RQL (Request Control) status bit,
117, 119
RQS (Request Service), 132
RS-232/UART triggering, 442
RST (Reset), 125
rules, tree traversal, 769
rules, truncation, 752
RUMode commands, 643
run, 133, 170
Run bit, 161, 163
run mode, mask test, 356
running configuration, 128, 426
Rx frame count (UART), 416
Rx source, 581
S
sample rate, 190
sampled data, 666
sampled data points, 599
SAMPlepoint commands, 643
SAV (Save), 128
save, 128, 378
SAVE commands, 377, 643
save filename, 379
save image, 380
save image with inksaver, 384
save mask, 386, 387
save mask test failures, 359
save path information, 388
save setup, 389
SAVE TO INTERN, 154
save waveform data, 390
save waveforms to pixel memory, 154
saved image, area, 381
saving and recalling data, 223
SBUS commands, 394
scale, 255, 435, 439
SCALe commands, 645
scale factors output on hardcopy, 264, 382
scale for channels, 220
scale units for channels, 221
scale units for external trigger, 242
scaling display factors, 213
SCPI commands, 59
scratch measurements, 680
screen area for hardcopy print
, 262
screen area for saved image, 381
screen data, 226
SECAM, 565, 569
seconds per division, 435