Technical data

Index
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide 875
DATA commands, 629
data conversion, 594
data displayed, 226
data format for transfer, 595
data output order, 597
data pattern length, 455, 532
data pattern width, 560
data point index, 621
data points, 184
data record, deep analysis, 424
data record, measurement, 424, 604
data record, precision analysis, 604
data record, raw acquisition, 604
data required to fill time buckets, 180
DATA source, I2S, 512
data structures, status reporting, 718
data transfer, 226
data, erasing, 145
data, saving and recalling, 223
DATE commands, 630
date, calibration, 195
date, system, 420
dB versus frequency, 245
DC coupling for edge trigger, 475
DC input coupling for specified channel, 207
dc RMS measured on waveform, 331
DDE (Device Dependent Error) status bit, 117,
119
decision chart, status reporting, 738
deep analysis record, 424
default conditions, 125
define channel labels, 211
define glitch trigger,
497
define measurement, 295
define measurement source, 315
define trigger, 449, 465, 466, 467, 469, 498,
549
defined as, 106
definite-length block query response, 56
definite-length block response data, 107
DELay commands, 630
delay measured to calculate phase, 306
delay measurement, 295
delay measurements, 320
delay parameters for measurement, 297
delay, how autoscale affects, 140
delayed time base, 431
delayed time base mode, how autoscale
affects, 140
delayed window horizontal scale, 439
delete mask, 352
delta time, 681
delta voltage measurement, 690
delta X cursor, 275
delta Y cursor, 275
DeskJet, 673
destination, 231
detecting probe types, 665, 669
device for hardcopy, 673
device-defined error queue clear, 115
differential probe heads, 214
differential signal type, 217, 239
differentiate math function,
182, 245, 252, 611
DIFFerentiate source for function, 257, 670
digitize channels, 146
DIGitize command, 49, 53, 593
digits, 107
disable anti-alias mode, 182
disable front panel, 423
disable function, 671
disabling calibration, 200
disabling channel display, 208
disabling status register bits, 116, 129
discontinued and obsolete commands, 657
display clear, 225
DISPlay commands, 223, 630
display commands introduction, 223
display connect, 666
display data, 226
display date, 420
display factors scaling, 213
display for channels, 208
display frequency span, 258
display measurements, 290, 314
display persistence, 230
display reference, 432, 434
display reset conditions, 125
display serial number, 171
display source, 231
display vectors
, 232
display, clearing, 145
display, lister, 273
display, oscilloscope, 230, 231, 232, 247, 421
display, serial decode bus, 401
displaying a baseline, 451
displaying unsynchronized signal, 451
DNS IP, 39
domain, 39
Domain softkey, 40
driver, printer, 678
duplicate mnemonics, 769
duration, 465, 466, 469
duration for glitch trigger, 493, 494, 498
duration pattern, 467
duration qualifier, trigger, 465, 466, 468
DURation trigger commands, 464
duration triggering, 441
duty cycle measurement, 49, 290, 299
E
EBURst trigger commands, 470
edge, 549
EDGE commands, 631
edge counter, 548
edge counter, Nth edge of burst, 471
edge coupling, 475
edge define, 449, 549
edge fall time, 300
edge parameter for delay measurement, 297
edge preshoot measured, 307
edge rise time, 312
edge slope, 478
edge source, 479
EDGE trigger commands, 474
edge triggering, 441
edges in measurement, 295
elapsed time in mask test, 349
ellipsis, 107
enable channel labels, 228
enabling calibration, 200
enabling channel display, 208
enabling status register bits, 116, 129
end of string (EOS) terminator, 752
end of text (EOT) terminator, 752
end or identify (EOI), 752
enter pattern, 449
EOI (end or identify), 752
EOS (end of string) terminator, 752
EOT (end of text) terminator, 752
Epson, 673
equivalent-time acquisition mode, 178, 183
erase data, 145, 225
erase functions, 145
erase measurements, 680
erase screen, 667
ERRor commands, 631
error frame count (CAN), 396
error frame count (UART), 414
error messages, 422, 707
error number, 422
error queue, 422, 729
error, measurement, 290
ESB (Event Status Bit), 130, 132
ESE (Standard Event Status Enable
Register), 116, 728
ESR (Standard Event Status Register), 118, 727
EVENt commands, 631
event status conditions occurred, 132
Event Status Enable Register (ESE), 116, 728
Event Status Register (ESR), 118, 175, 727
example code, :ACQuire:COMPlete, 180
example code, :ACQuire:SEGMented, 187
example code, :ACQuire:TYPE, 192
example code, :AUToscale, 141
example code, :CHANnel<n>:LABel, 211
example code, :CHANnel<n>:PROBe, 213
example code, :CHANnel<n>:RANGe, 219
example code, :DIGitize, 146
example code, :DISPlay:DATA, 227
example code, :DISPlay:LABel, 228
example code, :MEASure:PERiod, 315
example code, :MEASure:RESults, 309
example code, :MEASure:TEDGe, 321
example code, :MTESt, 339
example code, :RUN/:STOP, 170
example code, :SYSTem:SETup, 426
example code, :TIMebase:DELay, 703
example code, :TIMebase:MODE, 431
example code, :TIMebase:RANGe, 433
example code, :TIMebase:REFerence, 434
example code, :TRIGger:MODE, 447
example code, :TRIGger:SLOPe, 478
example code, :TRIGger:SOURce, 479
example code, :VIEW and :BLANk, 176
example code, :WAVeform, 611