Technical data

Index
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide 961
cursor mode, 311
cursor position, 312, 314, 316, 317, 319
cursor readout, 793, 797, 798
cursor reset conditions, 140, 621
cursor source, 313, 315
cursor time, 793, 797, 798
cursors track measurements, 361
cursors, how autoscale affects, 157
cursors, X1, X2, Y1, Y2, 310
cycle measured, 342
cycle time, 351
D
D- source, 703
D+ source, 704
data, 497, 499, 717
data 2, 500
data acquisition types, 710
data conversion, 712
data format for transfer, 712
data output order, 715
data pattern length, 472, 516
data pattern, CAN trigger, 471
data point index, 739
data points, 192
data record, measurement, 722
data record, raw acquisition, 722
data required to fill time buckets, 189
DATA source, I2S, 482
data structures, status reporting, 831
data, saving and recalling, 255
date, calibration, 213
date, system, 617
dB versus frequency, 271
DC coupling for edge trigger, 657
DC input coupling for specified channel, 225
DC RMS measured on waveform, 378
DC waveform generator output, 747
DDE (Device Dependent Error) status bit, 130,
132
decision chart, status reporting, 848
default conditions, 140, 621
define channel labels, 229
define glitch trigger, 668
define logic thresholds
, 776
define measurement, 338
define measurement source, 362
define trigger, 669, 675, 676, 679
defined as, 121
definite-length block query response, 52
definite-length block response data, 122
delay measured to calculate phase, 352
delay measurement, 338
delay measurements, 367
delay parameters for measurement, 340
delay, how autoscale affects, 157
delayed time base, 631
delayed window horizontal scale, 639
delete mask, 401
delta time, 793
delta voltage measurement, 802
delta X cursor, 310
delta Y cursor, 310
demo, 241
DEMO commands, 241
demo signal, 243
demo signal function, 242
demo signal phase angle, 245
demo signals output control, 246
detecting probe types, 779, 783
device-defined error queue clear, 129
DIFF source for function, 784
differences from 7000B Series oscilloscope
commands, 28
differential probe heads, 232
differential signal type, 235
differentiate math function, 271, 278, 729
DIFFerentiate source for function, 283
digital channel commands, 248, 249, 250, 251,
253
digital channel data, 714
digital channel labels, 260
digital channel order, 781
digital channel source for glitch trigger, 670
digital channels, 6
digital channels, activity and logic levels
on, 155
digital channels, groups of, 419, 421, 423
digital pod, stop displaying, 162
digital reset conditions, 141, 622
DIGital<d> commands, 247
digitize channels, 163
DIGitize command, 44, 49, 710
digits, 122
disable front panel, 620
disable function, 785
disabling calibration, 216
disabling channel display, 226
disabling status register bits, 130, 144
discontinued and obsolete commands, 769
display channel labels, 259
display clear, 257
DISPlay commands, 255
display commands introduction, 255
display connect, 780
display date, 617
display factors scaling, 231
display for channels, 226
display frequency span, 284
display measurements, 330, 361
display order, 781
display persistence, 261
display reference, 632, 634
display reference waveforms, 762
display reset conditions, 141, 622
display serial number, 181
display vectors, 262
display wave position, 781
display, lister, 307
display, oscilloscope, 249, 261, 273, 421, 618
display, serial decode bus, 456
displaying a baseline, 650
displaying unsynchronized signal, 650
DNS IP, 36
domain, 36
domain, network printer, 297
driver, printer, 790
DSO models, 6
duplicate mnemonics, 865
duration, 675, 676,
679
duration for glitch trigger, 664, 665, 669
duration qualifier, trigger, 675, 676
duration triggering, 642
duty cycle measurement, 45, 330, 342
E
EBURst trigger commands, 651
ECL channel threshold, 776
ECL threshold voltage for digital channels, 253
ECL trigger threshold voltage, 818
edge activity, 774
edge counter, Nth edge of burst, 652
edge coupling, 657
edge fall time, 343
edge parameter for delay measurement, 340
edge preshoot measured, 354
edge rise time, 359
EDGE SEARch commands, 562
edge search slope, 563
edge search source, 564
edge slope, 660
edge source, 661
EDGE trigger commands, 656
edge triggering, 642
edges (activity) on digital channels, 155
edges in measurement, 338
elapsed time in mask test, 398
ellipsis, 122
enable channel labels, 259
enabling calibration, 216
enabling channel display, 226
enabling status register bits, 130, 144
end of string (EOS) terminator, 862
end of text (EOT) terminator, 862
end or identify (EOI), 862
EOI (end or identify), 862
EOS (end of string) terminator, 862
EOT (end of text) terminator, 862
erase data, 257
erase measurements, 792
erase screen, 782
error frame count (CAN), 460
error frame count (UART), 541
error messages, 619, 821
error number, 619
error queue, 619, 841
error, measurement, 330
ESB (Event Status Bit), 145, 147
ESE (Standard Event Status Enable
Register), 130, 840
ESR (Standard Event Status Register), 132, 839
event status conditions occurred, 147
Event Status Enable Register (ESE), 130, 840
Event Status Register (ESR), 132, 185, 839