Specifications

$JLOHQW0$996HULHV6HUYLFH*XLGH
7HVWLQJ0DLQWDLQLQJWKH$JLOHQW996HULHV
Testing & Maintaining
the Agilent V24/V26
Series
3HUIRUPDQFH
7HVW&DUGLDF
2XWSXW
6WHS Connect the patient simulator to the C.O.
Module using the patient cable.
6WHS Configure the Patient simulator as
follows:
Injection temperature: 2 °C
Computation Const: 0.543
(Edward's Catheter)
Flow 5 l/min
6WHS Check displayed value against the
simulator configuration.
C.O. = 5 +/– 1 l/min.
7KHVHUHVXOWV
GRQRWKDYHWR
EHUHSRUWHG
3HUIRUPDQFH
7HVW&DUGLDF
2XWSXW
FRQWG
6HUYLFH7RRO
SURFHGXUH
1RWHThis procedure applies for both Service Tools
M1012-14232C and M1012-61601.
6WHS Make sure to be in Monitoring Mode.
Connect C.O. Interface Cable to module.
6WHS Connect one side of the Service Tool to
Injectate receptacle of C.O. Interface
Cable and the other side to Catheter
Cable receptacle.
6WHS Enter Measure C.O. Task Window and
check results.
Tblood = 37.0
o
C +/- 0.1
o
C
Tinj
= 0.0
o
C +/- 0.1
o
C
7KHVHUHVXOWV
GRQRWKDYHWR
EHUHSRUWHG
3HUIRUPDQFH
7HVW,QYDVLYH
3UHVVXUH
6WHS
Connect the patient simulator to the
Pressure module.
6WHS Set patient simulator to 0 pressure.
6WHS Make a Zero Calibration with the module.
6WHS Configure the patient simulator for
P(static) = 200 mmHg.
6WHS Wait for the display.
6WHS Check displayed value against the
simulator configuration. If there is a
difference, calibrate the module.
Note: If the Module was calibrated with a dedi-
cated reusable catheter, check the calibration
together with this catheter.
P = 200 +/– 5 mmHg
7KHVHUHVXOWV
GRQRWKDYHWR
EHUHSRUWHG
3HUIRUPDQFH
7HVW
7HPSHUDWXUH
6WHS
Connect the patient simulator to the
temperature input.
6WHS Configure the patient simulator to 40 °C
or alternatively 100 °F.
6WHS Check displayed value against the
simulator configuration.
+/– 0.2 °C
or +/– 0.4 °F
7KHVHUHVXOWV
GRQRWKDYHWR
EHUHSRUWHG
3HUIRUPDQFH
7HVW6S2
6WHS Connect the sensor to the SpO
2
module.
6WHS Measure the SpO
2
value on your own
finger (this assumes that you are healthy).
6WHS Check displayed value against the
simulator configuration.
Between 95 and 100%
7KHVHUHVXOWV
GRQRWKDYHWR
EHUHSRUWHG
7DEOH7HVWDQG,QVSHFWLRQ5HTXLUHPHQWV
7HVW%ORFN
1DPH
7HVWRU³,QVSHFWLRQ´WR3HUIRUP ([SHFWHG7HVW5HVXOWV :KDWWR5HFRUG
RQ6HUYLFH
5HFRUG