Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
80 Chapter 3
Programming Command Reference
TESTs Subsystem for AUTOMATIC TEST
Command Reference for Stand-by/Measuring Screens
The following commands are used to set the controls and parameters associated
with the initial test condition for the Stand-by/Measuring screens. The query
commands return the settings of those controls and parameters.
Send the "DISPlay:AUTO:STBY" command to display the AUTOMATIC TEST:
Stand-by screen before sending the following commands.
6 Measurement DCP Variable
TESTs:AUTO:VARiable:DCP:VOLT1 <real> [V]
TESTs:AUTO:VARiable:DCP:VOLT1?
TESTs:AUTO:VARiable:DCP:VOLT2 <real> [V]
TESTs:AUTO:VARiable:DCP:VOLT2?
TESTs:AUTO:VARiable:DCP:VOLT3 <real> [V]
TESTs:AUTO:VARiable:DCP:VOLT3?
TESTs:AUTO:VARiable:DCP:VOLT4 <real> [V]
TESTs:AUTO:VARiable:DCP:VOLT4?
TESTs:AUTO:VARiable:DCP:VOLT5 <real> [V]
TESTs:AUTO:VARiable:DCP:VOLT5?
TESTs:AUTO:VARiable:DCP:VOLT6 <real> [V]
TESTs:AUTO:VARiable:DCP:VOLT6?
These commands set the Variable field to DC Power and specify the six voltage
values at which the six measurements are to be made. These measurements are
made at one fixed traffic channel. The allowable range is from 3.0 to 11.0 (V) in
0.1 steps. The value 99.9 causes the DCP test to be skipped (---- shown in the table
cell). At preset, these are set to 3.0 (V).
6 Measurement TCH Variable
TESTs:AUTO:VARiable:TCH:CHANnel1 <int>
TESTs:AUTO:VARiable:TCH:CHANnel1?
TESTs:AUTO:VARiable:TCH:CHANnel2 <int>
TESTs:AUTO:VARiable:TCH:CHANnel2?
TESTs:AUTO:VARiable:TCH:CHANnel3 <int>
TESTs:AUTO:VARiable:TCH:CHANnel3?
TESTs:AUTO:VARiable:TCH:CHANnel4 <int>
TESTs:AUTO:VARiable:TCH:CHANnel4?
TESTs:AUTO:VARiable:TCH:CHANnel5 <int>
TESTs:AUTO:VARiable:TCH:CHANnel5?
TESTs:AUTO:VARiable:TCH:CHANnel6 <int>
TESTs:AUTO:VARiable:TCH:CHANnel6?