Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
72 Chapter 3
Programming Command Reference
TESTs Subsystem for AUTOMATIC TEST
bit 7 (128): RX Level
bit 8 (256): DC Current
bit 9 (512): Test aborted
The choices for each bit are 1 for Fail and 0 for Pass or Skip.
If there are no test results nor pass/fail results, all bits are set to 1, resulting to
return the value 1023.
Command Reference for Burst Timing/Power Ramp Measurement Screen
Send the "DISPlay:AUTO:BTIMing" command to display the Burst
Timing/Power Ramp measurement screen for AUTOMATIC TEST before sending
the following commands.
Burst Timing Measurement
TESTs:AUTO:RESults:BTIMing1?
TESTs:AUTO:RESults:BTIMing2?
TESTs:AUTO:RESults:BTIMing3?
TESTs:AUTO:RESults:BTIMing4?
TESTs:AUTO:RESults:BTIMing5?
TESTs:AUTO:RESults:BTIMing6?
This query command returns a set of test result values, <string 1>,
<string
2>
and <string 3>, for each of the six measurements of Burst Timing.
• <string 1> (1 digit) is 0 when all values are within the normal range, or 1 if any
measurement is overranged, underranged or not made.
• <string 2> (1 digit) is the binary data, 0 or 1, for the pass (0) or fail (1) result.
• <string 3> (4 digits) is the measured data ranging from −9.9 to +9.9 bits. If any
measurement is overranged, underranged or not made, the value −9.9 is
returned.
Power Ramp Graph Zoom
TESTs:AUTO:RESults:RAMP1:ZOOM ON|OFF|1|0
TESTs:AUTO:RESults:RAMP1:ZOOM?
TESTs:AUTO:RESults:RAMP2:ZOOM ON|OFF|1|0
TESTs:AUTO:RESults:RAMP2:ZOOM?
TESTs:AUTO:RESults:RAMP3:ZOOM ON|OFF|1|0
TESTs:AUTO:RESults:RAMP3:ZOOM?
TESTs:AUTO:RESults:RAMP4:ZOOM ON|OFF|1|0
TESTs:AUTO:RESults:RAMP4:ZOOM?
TESTs:AUTO:RESults:RAMP5:ZOOM ON|OFF|1|0
TESTs:AUTO:RESults:RAMP5:ZOOM?