Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
Chapter 3 65
Programming Command Reference
SMONitor Subsystem
3. Programming Command
Reference
Marker Measurement
SMONitor:RESults:MARKer?
This query command returns a set of values, <string 1>, <string 2>,
<string 3>, <string 4>, and <string 5>, for the marker position.
• <string 1> (1 digit) is 0 when all values are within the normal range, or 1 if any
measurement is overranged, underranged or not made.
• The definitions and effective ranges of <string 2> (10 digits), <string 3> (5
digits), <string 4> (7 digits), and <string 5> (5 digits) are shown in the table
below. If any measurement is overranged, underranged or not made, the values
9999999999 for <string 2>, −99.9 for <string 3> and <string 5>, and +999999
for <string 4>, are returned.
Marker Position Control
SMONitor:RESults:MARKer:POINt UP|DOWN
SMONitor:RESults:MARKer:POINt <real> [HZ|KHZ|MHZ|MAHZ]
SMONitor:RESults:MARKer:POINt?
This command allows you to move the marker UP or DOWN, or by a numeric
value <real>. The allowable range is from 0 to 400000 (Hz) for the 0 to 400 kHz
span, or from −100000 to +100000 (Hz) for the ±100 kHz span. At preset, this is
set to 1000 (Hz) if Span is set to 0 to 400 kHz, or 100 (Hz) if Span is set to ±100
kHz.
Measurement Range
SMONitor:RANGe −3DBM|+9DBM|+19DBM|+29DBM|+39DBM
SMONitor:RANGe?
This command specifies an absolute power level of Measurement Range. At
preset, this is set to +39DBM. The choices are as follows:
• −3DBM: The maximum input level is −3 dBm.
• +9DBM: The maximum input level is +9 dBm.
• +19DBM: The maximum input level is +19 dBm.
• +29DBM: The maximum input level is +29 dBm.
Value Definition Range: Span 0 to 400 kHz Range: Span ±100 kHz
<string 2> Absolute RF frequency
[Hz]
0880200000 to 0915200000,
1710200000 to 1785200000,
1850200000 to 1909800000
0880100000 to 0914900000,
1710100000 to 1784900000,
1850100000 to 1909500000
<string 3> Absolute RF level [dBm] −99.9 to +99.9 −99.9 to +99.9
<string 4> Relative RF frequency [Hz] +000000 to +400000 −100000 to +100000
<string 5> Relative RF level [dB] −99.9 to +0.00 −99.9 to +0.00