Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
Chapter 3 51
Programming Command Reference
CONFigure Subsystem
3. Programming Command
Reference
LOC. Update
CONFigure:SEQuence:SIGNaling:LOCUpdate ON|OFF|1|0
CONFigure:SEQuence:SIGNaling:LOCUpdate?
This command defines whether or not to include LOC. Update tests in the test flow
step. The choices are ON (1) for Run and OFF (0) for --- (skip). At preset, this is
set to ON.
Multi Band
CONFigure:SEQuence:MBANd DCS1800|OFF
CONFigure:SEQuence:MBANd?
This command specifies whether or not to include Multi Band tests for DCS1800
when GSM900 or E-GSM is specified by the Radio Format command.
CONFigure:SEQuence:MBANd GSM900|E-GSM|OFF
CONFigure:SEQuence:MBANd?
This command specifies whether or not to include Multi Band tests for GSM900 or
E-GSM when DCS1800 is specified by the Radio Format command.
If PCS1900 is specified by the Radio Format command, the Multi Band command
is automatically set to OFF.
Peak TX Power Test
CONFigure:SEQuence:TPOWer:HIGH <int>
CONFigure:SEQuence:TPOWer:HIGH?
CONFigure:SEQuence:TPOWer:MEDium <int>
CONFigure:SEQuence:TPOWer:MEDium?
CONFigure:SEQuence:TPOWer:LOW <int>
CONFigure:SEQuence:TPOWer:LOW?
This command defines whether or not to include Peak TX Power tests at the High,
Medium or Low range in the test sequence for the six measurements. <int> is a
binary coded decimal ranging from 0 to 63 as follows:
bit 0 (1): For testing TCH1 or DCP1
bit 1 (2): For testing TCH2 or DCP2
bit 2 (4): For testing TCH3 or DCP3
bit 3 (8): For testing TCH4 or DCP4
bit 4 (16): For testing TCH5 or DCP5
bit 5 (32): For testing TCH6 or DCP6
The choices for each bit are 1 for Run and 0 for --- (skip). At preset, this is set to
63.