Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
42 Chapter 3
Programming Command Reference
CONFigure Subsystem
FER Limit
CONFigure:CONDition:LIMit:FER <real h> [PCT]
CONFigure:CONDition:LIMit:FER?
This command specifies the high limit for FER (frame erasure rate) tests. The
allowable range is from 0.00 to 99.99 (%) in 0.01 steps. At preset, this is set to 0.12
(%).
NOTE If Option 040 is installed and the mode is set to GPRS in
MANUAL TEST, FER can not be measured.
Frequency Error Limit
CONFigure:CONDition:LIMit:FREQuency
<int l>,<int h> [HZ]
CONFigure:CONDition:LIMit:FREQuency?
This command specifies the low and high limits for Frequency Error tests for each
radio standard set by the Radio Format command. The allowable range is from
−999 to +999 (Hz) in 1 steps. At preset, these are set to −90 and +90 (Hz) for
GSM900 and E-GSM, −171 and +171 (Hz) for DCS1800, and −185 and +185 (Hz)
for PCS1900, respectively.
Loopback Delay
CONFigure:CONDition:LDELay SHORT|MID|LONG
CONFigure:CONDition:LDELay?
This command defines a time value of Loopback Delay. The choices are SHORT,
MID, and LONG (2 seconds). At preset, this is set to MID.
MS Power Class
CONFigure:CONDition:PCLass <int>
CONFigure:CONDition:PCLass?
This command specifies a value of MS Power Class for each radio standard set by
the Radio Format command. The allowable range and preset values are as follows:
RFORmat Allowable Range Preset Value
GSM900 2 (+39 dBm) to 5 (+29 dBm) 4 (+33 dBm)
E-GSM 2 (+39 dBm) to 5 (+29 dBm) 4 (+33 dBm)
DCS1800 1 (+30 dBm), 2 (+24 dBm), 3 (+36 dBm) 1 (+30 dBm)
PCS1900 1 (+30 dBm), 2 (+24 dBm), 3 (+33 dBm) 1 (+30 dBm)