Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
Chapter 3 37
Programming Command Reference
CONFigure Subsystem
3. Programming Command
Reference
Beeper Control
CONFigure:BEEPer ON|OFF|1|0
CONFigure:BEEPer?
This command toggles the beeper function between ON (1) and OFF (0). If set to
ON, there is a beep for each step of operation. If set to OFF, beeps excepting for
some errors and warnings are suppressed. At preset, this is set to ON.
Date
CONFigure:DATE <int y>,<int m>,<int d>
CONFigure:DATE?
This command defines the test date of the Test Set. <int y> is the year from 1990 to
2089, <int m> is the month from 01 to 12, and <int d> is the day from 01 to 31.
Network Configuration
CONFigure:NETWork:BSPa <int>
CONFigure:NETWork:BSPa?
This command defines the number of multiframes (BS_PA_MFRMS) between
two transmissions. The allowable range is from 2 to 9. At preset, this is set to 2.
CONFigure:NETWork:LAC <int>
CONFigure:NETWork:LAC?
This command defines the Location Area Code (LAC). The allowable range is
from 0 to 65535. At preset, this is set to 1.
CONFigure:NETWork:MCC <int>
CONFigure:NETWork:MCC?
This command defines the Mobile Country Code (MCC). The allowable range is
from 0 to 999. At preset, this is set to 1.
CONFigure:NETWork:MNC <int>
CONFigure:NETWork:MNC?
This command defines the Mobile Network Code (MNC). The allowable range is
from 0 to 99. At preset, this is set to 1.
CONFigure:NETWork:NCC <int>
CONFigure:NETWork:NCC?
This command defines the Network Color Code (NCC). The allowable range is
from 0 to 7. At preset, this is set to 1.
Panel Key Control
CONFigure:PKEY UNLOCK|LOCK
CONFigure:PKEY?
This command toggles the panel key control between UNLOCK and LOCK. At
preset, this is set to UNLOCK.