Specifications
Table Of Contents
- E6392-90042.pdf
- E6392-90042_manual
- Front Matter
- Contents
- 1 Preparing for Use
- 2 Programming Command Guidelines
- 3 Programming Command Reference
- IEEE Common Command
- CONFigure Subsystem
- DISPlay Subsystem
- HCOPy Subsystem
- RFGenerator Subsystem
- SMONitor Subsystem
- SYSTem Subsystem
- TESTs Subsystem for AUTOMATIC TEST
- All Tests Results
- All Tests Results
- Command Reference for Burst Timing/Power Ramp Measurement Screen
- Command Reference for DC Current Measurement Screen
- Command Reference for MS Information
- Command Reference for Peak TX Power Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Stand-by/Measuring Screens
- TESTs Subsystem for MANUAL TEST
- Command Reference for DC Current Measurement Screen
- Command Reference for Measuring Screens
- Command Reference for MS Information
- Command Reference for Peak TX Power /Burst Timing/Power Ramp Measurement Screen
- Command Reference for Phase/Frequency Error Measurement Screen
- Command Reference for Sensitivity/RX Quality/RX Level Measurement Screen
- Command Reference for Spectrum Monitor Measurement Screen
- Command Reference for Stand-by Screens
- TRIGger Subsystem
- 4 Programming Command Cross Reference
- 5 Example Programs
- A Syntax Diagram
- B Command Difference between E6392A & E6392B
- Index
Chapter 4 137
Programming Command Cross Reference
MANUAL TEST Screens
4. Programming Command
Cross Reference
MANUAL TEST Screens
Stand-by Screens
The following commands are used to set the controls and parameters associated
with the Stand-by screen.
Table 4-9 Command Cross Reference for Stand-by Screen
Item Command
BCCH Channel TESTs:MANual:BCCH:CHANnel <int>
TESTs:MANual:BCCH:CHANnel?
BCCH Frequency TESTs:MANual:BCCH:FREQuency <real>
TESTs:MANual:BCCH:FREQuency?
BS Level TESTs:MANual:AMPLitude <real>
TESTs:MANual:AMPLitude?
DC Power Mode TESTs:MANual:DCPower:MODE ON|OFF|1|0
TESTs:MANual:DCPower:MODE?
DC Power Voltage
TESTs:MANual:DCPower:VOLT <real>
TESTs:MANual:DCPower:VOLT?
Measurement Mode
[Option 002]
TESTs:MANual:MODE SYNC|ASYNC
TESTs:MANual:MODE?
Measurement Mode
[Option 040]
TESTs:MANual:MODE SYNC|GPRS
TESTs:MANual:MODE?
Measurement Mode
[Option 002, 040]
TESTs:MANual:MODE SYNC|ASYNC|GPRS
TESTs:MANual:MODE?
MS Signal
[Option 002 Async mode]
TESTs:MANual:SIGNal BURST|CW
TESTs:MANual:SIGNal?
Multi Band TESTs:MANual:MBANd OFF|DCS1800 [RFOR=GSM900/E-GSM]
TESTs:MANual:MBANd OFF|GSM900|E-GSM [RFOR=DCS1800]
TESTs:MANual:MBANd?
Power Control Level TESTs:MANual:PLEVel <int>
TESTs:MANual:PLEVel?
Radio Standard
TESTs:MANual:RFORmat GSM900|E-GSM|DCS1800|PCS1900
TESTs:MANual:RFORmat?
Slot Configuration
[Option 040]
TESTs:MANual:SCONfigure 1×1|2×1