User`s manual

Contents
Agilent E1346A 48 Channel Relay Multiplexer
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
User’s Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1. Getting Started with the Agilent E1346A . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Instrument Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Multiplexer Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Multiplexer Channel Descriptions and Connections . . . . . . . . . . . . . . . . . 12
Programming the Multiplexer Module . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Selecting Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SCPI Command Format Used in This Manual . . . . . . . . . . . . . . . . . . . 16
Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2. Configuring the Agilent E1346A Multiplexer Module . . . . . . . . . . . . . . . . . . . . . 17
Using This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Wiring a Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting User Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting the Analog Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting the Address Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Removing the Low-to-Guard Isolation Jumper . . . . . . . . . . . . . . . . . . . . . . 21
Selecting the Interrupt Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3. Using the Agilent E1346A Multiplexer Module . . . . . . . . . . . . . . . . . . . . . . . . 25
Using This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Multiplexer Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting Channels to Common for Making Measurements . . . . . . . . . . . . . . 26
Example: Connect Channel 02 to Common for Voltage Measurement . . . . . . 26
Example: Connect Channel 02 to the DT Tree Switch Terminals for an Ohms
Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Scanning a Range of Switchbox Channels . . . . . . . . . . . . . . . . . . . . . . . . 29
Example: Making Voltage Measurements by Scanning . . . . . . . . . . . . . . . 29
Example: Making 2-Wire Ohms Measurements by Scanning . . . . . . . . . . . . 31
Example: Making Multiple Scans . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Example: Making Continuous Scans . . . . . . . . . . . . . . . . . . . . . . . . . 31
Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Agilent E1346A 48 Channel Relay Multiplexer Contents 1