Service manual

Reference*
Designator
Agilent Part
Number
Qty Description Mfr**
Code
Mfr Part Number
A2
A2J101
A2J102
A2J103
A2K104-K105
A2K106
A2XU104
E1326-66502
44702-61603
1252-3712
1252-3416
0490-1556
0490-1555
1200-0817
1
1
1
1
2
1
1
INGUARD PRINTED CIRCUIT ASSY [a]
Cable Assembly - Ribbon 10 Conductor
Connector - Right Angle 2X6 12 Pin
Connector - Right Angle 4 Pin
Relay - Reed 2A 250MA 400VDC 5VDC-Coil
Relay - Reed 2A 250MA 400VDC 5VDC-Coil
Socket - 40 Pin Integrated Circuit
28480
28480
18873
27264
71707
71707
00779
E1326-66502
44702-61603
68668-004
705-53-0108
3500-0050
3500-0051
2-640379-1
CBL1
CBL2
CBL3
E1326-61605
E1326-61601
E1326-61606
1
1
1
CABLE ASSEMBLIES
Cable Assembly - 4 Conductor
Cable Assembly - 6 Conductor
Cable Assembly - 4 Conductor Ribbon
28480
28480
28480
E1326-61605
E1326-61601
E1326-61606
LBL1
MP1
MP2
MP3-MP6
MP9-MP10
PNL1
SHD1
E1326-84302
E1300-45101†
E1300-45102†
1510-0091
1400-1567
E1326-00208†
E1300-80601
1
2
4
2
1
1
MECHANICAL PARTS
Label - Serial Number
HNDL-KIT TOP, Agilent†
HNDL-KIT BTM, VXI †
Binding Post - Red
Wire Saddle - Nylon
PNL-EXTERNAL VM†
Shield - Safety
28480
28480
28480
28480
28480
28480
28480
E1326-84302
E1300-45101†
E1300-45102†
1510-0091
1400-1567
E1326-00208†
E1300-80601
SCR1-SCR2
SCR3-SCR4
SCR9-SCR10
0515-0372
0515-2140
0515-1968
0515-2743
2950-0001
3050-0593
1
2
2
2
4
4
COMMON HARDWARE
SCR Pan-Head M3.0 X .5 Torx T10
SCR-THD-RLG M2.5 X0.45 14mm
SCR Pan-Head M2.5 X 11 Pozidriv
SCR-FH M2.5 X 8 THREAD ROLLING
Nut-Hex-DBL Chamfer 3/8-32 THD
Washer-Spring NO. 3/8
28480
28480
28480
28480
28480
28480
0515-0372
0515-2140
0515-1968
0515-2743
2950-0001
3050-0593
* See Table 6-2 for Reference Designator definitions
** See Table 6-3 for Code List of Manufacturers
[a] Repair limited to replacement of parts listed - see Introduction for ordering information
† These parts are not compatible with older version fixed handles or their corresponding front panels. To replace one or more
of these old parts, you must order all three new parts (Top and Bottom Handle Kits AND External Panel).
Table 6-2. Agilent E1326B Reference Designators
Agilent E1326B Reference Designators
A .......................................... assembly
CBL ............................................ cable
F ................................................... fuse
J ................ electrical connector (jack)
JM ........ electrical connector (header)
K ...................................................relay
LBL ............................................. label
MP .................. misc. mechanical part
P ............... electrical connector (plug)
PNL ............................................ panel
SCR ............................................ screw
SHD .......................................... shield
SW ............................................ switch
XU ............... socket, integrated circuit
6-2 Replaceable Parts