User`s manual

Contents
C-Size VXIbus Configuration Guide
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
User Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the C-Size Configuration Guide and Agilent VIC . . . . . . . . . . . . . . . . . 9
For More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Terms Used In This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Procedure 1:
Configure the VXI Mainframe
Step-1 : Connect Mainframe Safety Ground (if necessary) . . . . . . . . . . . . . . 1-2
Grounding Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Step-2 : Connect the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Step-3 : Where To Go Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Procedure 2:
Set Up the VXI System Controller
Setting Up the Agilent E1406A Command Module . . . . . . . . . . . . . . . . . . . 2-2
E1406-1 : Set the Command Module as Resource Manager . . . . . . . . . . . . . 2-3
E1406-2 : Set the Command Module as Slot 0 Device . . . . . . . . . . . . . . . . 2-4
E1406-3 : Set the Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
E1406-4 : Set the Bus Request Level . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
E1406-5 : Configure the Command Module’s Shared RAM . . . . . . . . . . . . . 2-7
E1406-6 : Set the Command Module’s Servant Area . . . . . . . . . . . . . . . . . 2-8
E1406-7 : Set Command Module’s Primary GPIB Address . . . . . . . . . . . . . . 2-9
E1406-8 : Install the Command Module into the Mainframe . . . . . . . . . . . . . 2-10
E1406-9 : Connect Interface Cables . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
E1406-10 : Apply Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Alternate Command Module Configurations . . . . . . . . . . . . . . . . . . . . . 2-15
E1406-11 : Where To Go Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Setting Up a Series 700 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Series 700-1 : Set up the Agilent E1482B VXIbus Extender Module . . . . . . . . . 2-20
Series 700-2 : Set Up the Agilent E1406A Command Module . . . . . . . . . . . . 2-23
Series 700-2A : Setting the Command Module Logical Address . . . . . . . . . . . 2-24
Series 700-2B : Setting the Command Module Servant Area . . . . . . . . . . . . . 2-24
Series 700-2C : Setting the Command Module Primary GPIB Address . . . . . . . 2-25
Series 700-2D : Disabling the Command Module’s Slot 0 Capability . . . . . . . . 2-26
Series 700-2E : Disabling the Command Module’s VMEbus Time Out
Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Series 700-3 : Install the Agilent E1482B Extender Module in the Mainframe . . . . 2-28
Installing the E1406A Command Module . . . . . . . . . . . . . . . . . . . . . . . 2-28
Series 700-4 : Connect the MXIbus and INTX Cables . . . . . . . . . . . . . . . . 2-29
Series 700-5 : Apply Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Assigning Interrupt Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Series 700-6 : Where To Go Next . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
C-Size VXIbus Configuration Guide Contents 1