User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-76 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
N907 CMU failed Rr/Rf 1kohm test.
N908 CMU failed Rr/Rf 10kohm test.
N909 CMU failed Rr/Rf 100kohm test.
N910 CMU failed TRD IVAmp test.
N911 CMU failed N_HPF1/N_LPF1 10kHz test.
N912 CMU failed N_HPF1/N_LPF1 200kHz test.
N913 CMU failed N_HPF1/N_LPF1 1MHz test.
N914 CMU failed N_HPF1/N_LPF1 2MHz test.
N915 CMU failed N_HPF1/N_LPF1 5MHz test.
N916 CMU failed NA1 test.
N917 CMU failed NA2 test.
N918 CMU failed NA3 test.
N919 CMU failed IV saturation detector test.
N920 CMU failed normal status test.
N921 CMU failed normal status test.
N922 CMU failed IV saturation status test.
N923 CMU failed IV saturation status test.
N924 CMU failed unbalance detector test.
N925 CMU failed normal status test.
N926 CMU failed normal status test.
N927 CMU failed unbalance status test.
N928 CMU failed unbalance status test.
N929 CMU failed over current detector test.
N930 CMU failed normal status test.
N931 CMU failed normal status test.
N932 CMU failed over current status test.
N933 CMU failed over current status test.