User`s guide
Table Of Contents
- User’s Guide
- 1 Getting Started
- 2 Introduction
- 3 Installation
- 4 Using EasyEXPERT
- 5 Classic Test Definition
- I/V Sweep
- Multi Channel I/V Sweep
- I/V List Sweep
- I/V-t Sampling
- C-V Sweep
- Direct Control
- Function Setup
- Auto Analysis Setup
- Display Setup
- SMU Range Setup Window
- ADC and Integration Time Setup Window
- Advanced Setup Window
- CMU Range Setup Window
- Advanced Setup Window for C-V Sweep
- Switching Matrix Control
- SPGU Control
- SPGU Pulse Setup Window
- Load Z Setup Window
- Pulse Switch Setup Window
- SPGU ALWG Setup Window
- Define ALWG Waveform Window
- 6 Application Test Definition
- 7 Function Details
- I/V Sweep Measurement
- Multi Channel I/V Sweep Measurement
- I/V-t Sampling Measurement
- C-V Sweep Measurement
- SPGU Module
- Sweep Abort Function
- Standby Function
- Bias Hold Function
- Current Offset Cancel
- SMU CMU Unify Unit
- Atto Sense and Switch Unit
- SMU/PG Selector
- SMU Ranging Mode
- SMU Compliance
- SMU Pulse
- SMU Measurement Time
- SMU Filter
- SMU Series Resistor
- Interlock Function
- Auto Power Off Function
- Initial Settings
- 8 Built-in Programming Tool
- 9 If You Have a Problem
- When You Operate B1500A
- When You Perform Measurement
- Measurement Takes More Time than Specified
- Noise Affects the Measured Values
- Voltage Measurement Error is Large
- SMU Oscillates for High-Frequency Device Measurements
- SMU Oscillates for Negative Resistance Measurements
- Large Current Causes High Temperature (Thermal Drift)
- Measurement Damages the Device under Test
- Leaving Connections Damages Devices after Measurement
- Unexpected Sampling Measurement Data is Returned
- MFCMU Causes Unbalance Condition
- Before Shipping to Service Center
- Data Backup and Recovery
- B1500A System Recovery
- Updating EasyEXPERT
- Error Codes
- 10 Application Library and Utilities
9-70 Agilent B1500 User’s Guide, Edition 7
If You Have a Problem
Error Codes
3426 WGFMU EEPROM CRC data is invalid.
3427 WGFMU EEPROM CRC data of format revision data is invalid.
3428 WGFMU EEPROM CRC data of serial number data is invalid.
3429 WGFMU EEPROM CRC data of system timing data is invalid.
3430 WGFMU EEPROM CRC data of DAC DCM PS data is invalid.
3431 WGFMU EEPROM CRC data of ADC DCM PS data is invalid.
3432 WGFMU EEPROM CRC data of DAC clock edge data is invalid.
3433 WGFMU EEPROM CRC data of ADC clock edge data is invalid.
3434 WGFMU EEPROM CRC data of DAC level calibration data is invalid.
3435 WGFMU EEPROM CRC data of ADC level calibration data is invalid.
3436 WGFMU EEPROM CRC data of DAC skew calibration data is invalid.
3437 WGFMU EEPROM CRC data of ADC skew calibration data is invalid.
3438 RSU EEPROM CRC data of format revision data is invalid.
3439 RSU EEPROM CRC data of serial number data is invalid.
3440 RSU EEPROM CRC data of type id data is invalid.
3441 RSU EEPROM CRC data of calibration data is invalid.
3450 WGFMU EEPROM data is invalid.
3451 WGFMU EEPROM data of RSU type is invalid.
3452 WGFMU EEPROM data of RSU cable type is invalid.
3460 Main DAC, Main ADC test failed.
3461 Bias DAC, Main ADC test failed.
3462 Main DAC, Reference ADC test failed.
3463 VM function test failed.
3464 IM offset test failed.
3465 IM short test failed.
3480 Invalid frame configuration.
3481 Invalid frame configuration.
3482 Frame has no modules.